American Society for Testing and Materials (ASTM). Current edition 2000, 6 p. This specification deals with carbon steel tee rails for use in railway track, including export and industrial applications. Rails shall be furnished by as-rolling, head hardening, or fully heat treatment processes. Hydrogen content shall be measured either during the continuous casting process or...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published January 2005. Originally approved in 1999. Last previous edition approved in 1999 as A 1000 – 99. 5 p. This specification covers a quality of round and shaped plain carbon and alloy steel spring wire, uniform in quality and temper, intended for the manufacture of mechanical springs...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published September 2007. Originally approved in 2000. Last previous edition approved in 2007 asA 1008/A 1008M – 07. 9 p. This specification covers cold-rolled, carbon, structural, high-strength low-alloy, high-strength low-alloy with improved formability, solution hardened, and bake...
ASTM, 2004 (Re approved 2009), 3p - A101 Standard Specification for Ferrochromium
Brief Summary
This specification covers two types of ferrochromium designated as high carbon and low carbon, the latter including nitrogen-bearing and vacuum grades. The grades which are available in different sizes shall conform to the required chemical composition for chromium, carbon, silicon,...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published September 2007. 8p. This specification covers hot-rolled, carbon, structural, high-strength low-alloy, high-strength low-alloy with improved formability, and ultra-high strength steel sheet and strip, in coils and cut lengths
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2007. Published April 2007. Originally approved in 2000. Last previous edition approved in 2002 as A 1012-02. 4 p. This specification describes seamless and welded ferritic, austenitic and duplex alloy steel tubing on which the external or internal surface, or both, has been modified by a cold...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published April 2006. Originally approved in 2000. Last previous edition approved in 2003 as A 1014 – 03. 3 p. This specification covers a precipitation hardening bolting material (UNS N07718) for high temperature service. This specification is expressed in both inch-pound and in SI...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published October 2005. Originally approved in 2001. Last previous edition approved in 2001 as A 1015 – 01. 3 p. This standard covers guidelines for ordering and examining tubular products for sanitary applications by videoborescoping. This method uses movable camera probe at the end of a...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2008. Published November 2008. Originally approved in 2001. Last previous edition approved in 2004 as A1016/A1016M - 04a. 11 p. This specification covers a group of requirements that, unless otherwise specified in an individual specification, shall apply to the ASTM product specifications noted...
ASTM International, 16 с.
Утверждено: 1 март 2014 г.
Настоящие технические условия содержат ряд требований, которые, если в отдельных технических условиях не указано иное, распространяются на технические условия к изделиям ASTM.
American Society for Testing and Materials (ASTM). Current edition approved Jan. 15, 2007. Published January 2007. Originally approved in 2001. Last previous edition approved in 2006 as A 1018/A 1018M – 06c. 9 p. This specification covers hot-rolled, heavy-thickness coils beyond the size limits of Specification A 1011/A 1011M. The product is available in six designations:...
ASTM, 2004 (Re approved 2009), 3p - A102 Standard Specification for Ferrovanadium
Brief Summary
This specification covers different sizes of one grade of ferrovanadium. The material shall undergo chemical analysis and shall conform to the requirements as to composition of the following chemical elements: vanadium, carbon, silicon, aluminum, sulfur, and phosphorus.
Scope...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 2001. Last previous edition approved in 2002 as A 1021 – 02. 4 p. This specification covers martensitic chromium stainless steel forgings, forged bar, and forging stock for high temperature service. The mechanical properties are developed by...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published October 2007. Originally approved in 2002. Last previous edition approved in 2002 asA 1023/A 1023M – 02. 37 p. This specification covers the general requirements for the more common types of stranded steel wire ropes. Included in this specification are wire ropes in various grades...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. 6 p. This practice covers the determination of comparative hardness values by applying the Ultrasonic Contact Impedance Method (UCI Method).
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2009. Published January 2010. Originally approved in 2004. Last previous edition approved in 2004 as A1042/A1042M - 04. 8 p. This specification covers composite corrugated steel pipe, intended for uses such as storm water drainage, sanitary sewers, underdrains, construction of culverts, and similar...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2005. Published June 2005. Originally approved in 1926. Last previous edition approved in 2003 as A 105/A 105M – 03. 5 p. This specification covers forged carbon steel piping components for ambient- and higher-temperature service in pressure systems
ASTM, 2014, 5p. A 105/ 105M, Standard Specification for Carbon Steel Forgings for Piping Applications This specification covers standards for forged carbon steel piping components, that is, flanges, fittings, valves, and similar parts, for use in pressure systems at ambient and higher-temperature service conditions. Materials shall be subjected to heat treatment (annealing,...
American Society for Testing and Materials (ASTM). 2001. 4p. This specification covers forged carbon steel piping components for ambient- and higher-temperature service in pressure systems. Included are flanges, fittings, valves, and similar parts ordered either to dimensions specified by the purchaser or to dimensional standards such as the ASME and API specifications referenced...
ASTM, 2012, 4p. A 1053 Standard Specification for Welded Ferritic-Martensitic Stainless Steel Pipe
Brief Summary
This specification covers seam welded ferritic-martensitic stainless steel pipe intended for abrasive and general corrosion service. The pipes are classified according to sizes, from NPS 2 to NPS
36. The pipe shall be made using Electric Resistance Welding (ERW) or...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2008. Published November 2008. 5 р. This specification covers the general requirements for protective zinc coatings (hereinafter referred to as the coatings) to be applied by the thermo-diffusion coating (TDC) method, to various products made of carbon steel, including low and high tensile parts...
American Society for Testing and Materials (ASTM). 2004. 10p. This specification covers seamless carbon steel pipe for high-temperature service in NPS Vs to NPS 48 [DN 6 to DN 1200] inclusive, with nominal (average) wall thickness as given in ASME B
36.lOM. It shall be permissible to furnish pipe having other dimensions provided such pipe complies with all other requirements of...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2011. Published December 2011. 9 p. This specification covers seamless carbon steel pipe for high-temperature service in NPS Vs to NPS 48 [DN 6 to DN 1200] inclusive, with nominal (average) wall thickness as given in ASME B
36.lOM. It shall be permissible to furnish pipe having other dimensions...
ASTM, 2014, 9p. A 106/ 106M, Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service Applications This specification covers carbon steel pipe for high-temperature service. These pipes are suitable for welding, bending, flanging, and similar forming operations. Mechanical testing of the specimens shall include tensile, bending, flattening, hydrostatic...
1.1.Данная спецификация2 распространяется на трубы из бесшовной углеродной стали для эксплуатации в условиях высокой температуры (Примечание 1) размером NPS (номинальный размер трубы) от 1/8 до NPS 48 [DN 6 по DN 1200] (прим. 2) включительно, с номинальной (средней) толщиной стенки, согласно ANSI B
36.10. Допускается поставлять трубы, имеющие другие размеры, при условии, что...
American Society for Testing and Materials (ASTM). 2007. 8p. This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as...
American Society for Testing and Materials (ASTM). Current edition approved June 10, 2000. Published September 2000. 6 р. This specification covers metallic-coated steel fence fabric having a series of horizontal (line) wires, with vertical (stay) wires woven or wrapped around the line wires, forming rectangular openings. The fence fabric is suitable for use in fences for farm...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2004. Published June 2004. 4 р. This specification covers metallic-coated steel barbed wire, consisting of a strand of two wires. The barbed wire is available with aluminum, zinc, and zinc-5 % aluminum-mischmetal alloy coatings, with a number of coating weights, in a number of different...
American Society for Testing and Materials (ASTM). Current edition approved October 10, 2002. Published December 2002. 8 р. This specification covers the requirements for zinc coating (galvanizing) by the hot-dip process on iron and steel products made from rolled pressed and forged shapes, castings, plates, bars, and strips
ASTM, 1996 (Re approved 2007), 6p - A125 Standard Specification for Steel Springs, Helical, Heat-Treated.
Brief Summary
This specification covers the standard for hot-coiled, heat-treated helical compression springs with tapered, closed, squared and ground ends made of hot-wrought round steel bars. Cross sections for hot-wrought round, square, and round-cornered square bars of...
ASTM, 1993 (Re approved 2012), 3p - A128 Standard Specification for Steel Castings, Austenitic Manganese.
Brief Summary
This specification covers Hadfield austenitic manganese steel castings and alloy modifications. The castings shall be suitably heat treated to achieve toughness and ductility. This heat treatment shall consist of uniformly heating the castings to a...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published October 2005. Originally approved in 1931. Last previous edition approved in 2001 as A 134 – 96 (2001). 4 p. This specification covers electric-fusion (arc)-welded straight seam or spiral seam steel pipe NPS 16 and over in diameter (inside or outside as specified by purchaser), with...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2009. Published November 2009. Originally approved in 1931. Last previous edition approved in 2006 as A135/A135M – 06. 9 p. This specification covers two grades of electric-resistance-welded steel pipe in NPS 2 to NPS 30 [DN 50 to DN 750] inclusive, with nominal (average) wall thickness up to 0.500...
Publisher: ASTM
Publish Date: 2014
Pages: 9
Language: English
Format: PDF
Document Scope
1.1 This specification covers two grades of electricresistance-
welded steel pipe in NPS 2 to NPS 30 [DN 50 to DN
750] inclusive, with nominal (average) wall thickness up to
0.500 in. [12.70 mm], inclusive, and in nominal sizes NPS 3⁄4
to NPS 5 [DN 20 to DN 125] inclusive with...
Publisher: ASTM Publish Date: 2015 Pages: 6 Language: English Book of Standards Volume: 01.01 Abstract This specification covers five grades of electric-fusion(arc)-welded straight-seam or helical steel pipe including pipe of NPS 4 and over. The required chemical composition, tensile requirements of the steel, and the tensile requirements of the production welds are presented....
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2008. Published March 2008. Originally approved in 1955. Last previous edition approved in 2005 as A148/A148M – 05. 4 p. This specification covers carbon steel, alloy steel, and martensitic stainless steel castings that are to be subjected to higher mechanical stresses than those covered in...
American Society for Testing and Materials (ASTM). Current edition approved September 10, 2002. Published November 2002. 4 р. This specification2 covers minimum-wall-thickness, electric-resistance-welded tubes made of carbon steel and carbon-manganese steel intended for use as boiler tubes, boiler flues, superheater flues, and safe ends.
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published October 2005. 2 p. This specification covers minimum-wall-thickness, seamless cold-drawn low-carbon steel tubes for tubular heat exchangers, condensers, and similar heat transfer apparatus. This specification covers tubes 1⁄8 to 3 in. [3.2 to 76.2 mm], inclusive, in outside diameter.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2006. Published September 2006. Originally approved in 1935. Last previous edition approved in 2001 as A 181/A 181M – 01. 3 p. This specification covers nonstandard as-forged fittings, valve components, and parts for general service. Forgings made to this specification are limited to a maximum...
This standard is issued under the fixed designation A182/A182M; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This...
ASTM International, 25 с. Утверждено: 1 мая 2014 г. Настоящая спецификация включает кованые компоненты труб из низколегированных и нержавеющих сталей, предназначенные для использования в напорных системах. Сюда входят фланцы, фитинги, клапаны и подобные детали, изготовленные по заданным размерам или по стандартам на размеры, таким как спецификации ASME.
Настоящие технические условия охватывают элементы трубопроводов из кованой низколегированной и нержавеющей стали для использования их в системах под давлением. Элементы включают в себя фланцы, фитинги, клапаны и аналогичные детали по заданным размерам или размерным стандартам, таким как технические условия ASME, которые указаны в качестве ссылочного документа
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2009. Published May 2009. 5p. This specification covers carbon steel track bolts and carbon steel nuts for use in conjunction with joint bars to connect rails in railroad track. Two grades of track bolts are defined: - Grade 1, Low-Carbon, Untreated, primarily for industrial and mine track use....
American Society for Testing and Materials (ASTM). Current edition approved September 10, 2002. Published November 2002. 3 р. This specification covers minimum-wall-thickness, seamless carbon steel boiler and superheater tubes for highpressure.
Стандартная спецификация для болтовых материалов из нержавеющей и легированной стали, используемых при высоких температурах. Год издания 2010. Язык - английский
Published: 01.06.2014
Number of Pages: 12
This specification covers alloy steel and stainless steel bolting material for pressure vessels, valves, flanges, and fittings for high temperature or high pressure service, or other special purpose applications. Ferritic steels shall be properly heat treated as best suits the high temperature characteristics of each grade. Immediately...
Стандарт распространяется на болтовые крепления из легированных и нержавеющих сталей, используемые в сосудах, работающих под давлением, арматуре, фланцах и фитингах для условий эксплуатации при высоких температурах и давлениях или других специальных условий эксплуатации.
ASTM 2001, 11p. A 194/A 194M Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both. Abstract This specification covers a variety of carbon, alloy, and martensitic and austenitic stainless steel nuts. These nuts are intended for high-pressure or high-temperature service, or both. Bars from which the nuts are made...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2013. Published October 2013. Originally approved in 1936. Last previous edition approved in 2012 as A194/A194M–12a. 12 p. This specification covers a variety of carbon, alloy, and martensitic stainless steel nuts in the size range 1⁄4 through 4 in. and metric M6 through M100 nominal. It also...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2009. Published November 2009. 35 р. This general requirements specification covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled steel plates for pressure vessels. These materials are intended to be suitable for fusion...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published October 2007. Originally approved in 1938. Last previous edition approved in 2003 as A 209/A 209M – 03. 3 p. This specification covers several grades of minimum-wall-thickness, seamless, carbon-molybdenum alloy-steel, boiler and superheater tubes. This specification covers tubes...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2011. Published November 2011. 14 p. This specification covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes, designated Grades T5, TP304, etc. These steels are listed in Tables 1 and 2. Grades containing the letter, H, in their designation, have...
Publisher: ASTM
Publish Date: 2015
Pages: 14
Language: English
ISBN: N/A
Abstract
This specification covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes. Grades containing the letter H in their designation have requirements different from those of similar grades not containing the letter H. These different requirements provide...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published October 2005. 2 p. This specification covers minimum-wall-thickness, electric-resistance-welded, carbon steel tubes to be used for heat exchangers, condensers, and similar heat-transfer apparatus. The tubing sizes usually furnished to this specification are to 3 in. [76.2 mm] in...
This specification covers carbon steel castings for valves, flanges, fittings, or other pressure-containing parts for high-temperature service and of quality suitable for assembly with other castings or wrought-steel parts by fusion welding
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. Originally approved in 1939. Last previous edition approved in 2005 as A 227/A 227M – 99 (2005). 4 p. This specification covers two classes of round colddrawn steel spring wire having properties and quality for the manufacture of mechanical springs that are not subject...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 1939. Last previous edition approved in 1999 A 229/A 229M – 99. 4 p. This specification covers two classes of oil-tempered steel spring wire intended especially for the manufacture of mechanical springs and wire forms.
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1939. Last previous edition approved in 1999 as A 230/A 230M – 99. 4 p. This specification covers the highest quality of round carbon steel spring wire, uniform in quality and temper, intended especially for the manufacture of valve springs and...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2004. Published September 2004. Originally approved in 1939. Last previous edition approved in 2002 as A 231/A 231M – 96 (2002). 4 p. This specification covers round chromium-vanadium alloy steel spring wire having properties and quality intended for the manufacture of springs used at moderately...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1939. Last previous edition approved in 1999 as A 232/A 232M – 99. 4 p. This specification covers the highest quality of round chromium-vanadium alloy steel valve spring wire, uniform in quality and temper, intended for the manufacture of valve...
This specification covers wrought carbon steel and alloy steel fittings of seamless and welded construction covered by the latest revision of ANSI B16.9, ANSI B16.11, ANSI B16.28, MSS SP-79, and MSS SP-
95. These fittings are for use in pressure piping and in pressure vessel fabrication for service at moderate and elevated temperatures. Fittings differing from these ANSI and MSS...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2007. Published April 2007. Originally approved in 1940. Last previous edition approved in 2006 as A 234/A 234M – 06a. 8 p. This specification covers wrought carbon steel and alloy steel fittings of seamless and welded construction covered by the latest revision of ASME B16.9, B16.11, MSS-SP-79,...
ASTM, 2014, 9p. A 234/A 234M, Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service This specification covers wrought carbon steel and alloy steel fittings of seamless and welded construction. These fittings are for use in pressure piping and in pressure vessel fabrication for service at moderate and...
American Society for Testing and Materials (ASTM). Current edition approved March 15, 2006. Published March 2006. 12p. This specification covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications.
Publisher: ASTM
Publish Date: 2015
Pages: 14
Language: English
ISBN: N/A
Abstract
This specification covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications. The steel shall conform to the requirements as to chemical composition specified. The material shall conform to the...
American Society for Testing and Materials (ASTM). 2004, 3p. A 242/A 242M-04 Brief summary This specification covers high-strength low-alloy structural steel shapes, plates, and bars for welded, riveted, or bolted construction intended primarily for use as structural members where savings in weight (mass) or added durability are important. Steel specimens shall be semi-killed...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2010. Published November 2010. 9 p. This specification covers nominal-wall-thickness welded tubes and heavily cold worked welded tubes made from the austenitic steels listed in Table 1, with various grades intended for such use as boiler, superheater, heat exchanger, or condenser tubes
Publisher: ASTM
Publish Date: 2015
Pages: 10
Language: English
Format: PDF
Document Scope
1.1 This specification covers nominal-wall-thickness
welded tubes and heavily cold worked welded tubes made from
the austenitic steels listed in Table 1, with various grades
intended for such use as boiler, superheater, heat exchanger, or
condenser tubes.
1.2 Grades TP304H,...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1941. Last previous edition approved in 2004 as A 250/A 250M – 04. 4 p. This specification covers several grades, designated T1, T1a, T1b, T2, T11, T12 and T22, of minimum-wall-thickness, electric-resistance-welded, carbon-molybdenum and...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 10, 2002. Published September 1998. Reapproved 2002. 7 p. This specification covers nominal (average) wall steel pipe piles of cylindrical shape and applies to pipe piles in which the steel cylinder acts as a permanent load-carrying member, or as a shell to form cast-in-place concrete piles.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published October 2007. Originally approved in 1942. Last previous edition approved in 2002 as A 255 – 02. 26 p. These test methods cover the identification and description of test methods for determining the hardenability of steels. The two test methods include the quantitative end-quench...
ASTM, 2010. — 16 p, A262 Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels Abstract This specification covers the standard practices for detecting susceptibility to intergranular attack in austenitic stainless steels. These practices include five intergranular corrosion tests, namely: (1) oxalic acid etch test for...
ASTM, 2013. — 17 p, A262 Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels Brief Summary This specification covers the standard practices for detecting susceptibility to intergranular attack in austenitic stainless steels. These practices include five intergranular corrosion tests, namely: (1) oxalic acid etch test for...
ASTM, 2015. — 20 p, A262 Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels Brief Summary This specification covers the standard practices for detecting susceptibility to intergranular attack in austenitic stainless steels. These practices include five intergranular corrosion tests, namely: (1) oxalic acid etch test for...
1. Scope* 1.1 This specification covers grades of nominal-wallthickness, stainless steel tubing for general corrosion-resisting and low- or high-temperature service, as designated in Table 1. 1.2 The tubing sizes and thicknesses usually furnished to this specification are 1⁄4 in. (6.4 mm) in inside diameter and larger and 0.020 in. (0.51 mm) in nominal wall-thickness and...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2010. Published May 2010. 6 р. This specification covers grades of nominal-wallthickness, stainless steel tubing for general corrosion-resisting and low- or high-temperature service, as designated in Table 1. The tubing sizes and thicknesses usually furnished to this specification are 1⁄4 in....
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2008. Published November 2008. Originally approved in 1901. Last previous edition approved in 2005 as A27/A27M – 05. 4 p. This specification covers carbon steel castings for general applications that require up to 70 ksi (485 MPa) minimum tensile strength.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published September 2007. Originally approved in 1944. Last previous edition approved in 2006 as A 275/A 275M – 06. 7 p. This practice covers a procedure for magnetic particle examination of steel forgings. The procedure will produce consistent results upon which acceptance standards can be...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2008. Published October 2008. 7 р. This specification covers hot-finished or cold-finished bars except bars for reforging . It includes rounds, squares, and hexagons, and hot-rolled or extruded shapes, such as angles, tees, and channels in the more commonly used types of stainless steels. The...
American Society for Testing and Materials (ASTM). 2003, 2p. A 283/A 283M-03
Brief summary
This specification covers four grades of carbon steel plates of structural quality for general application. Steel samples shall be melt processed by either open-hearth, basic-oxygen, or electric furnace. Heat and product analysis shall be performed wherein steel materials shall conform to...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2013. Published November 2013. Originally approved in 1946. Last previous edition approved in 2012 as A283/A283M – 12a. 3 p. This specification covers two grades (C and D) of carbon steel plates of structural quality for general application. When the steel is to be welded, a welding procedure...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2004. Published April 2004. 17 р. This specification covers a group of common requirements which, unless otherwise specified in the purchase order or in an individual specification, shall apply to carbon and alloy steel bars under each of the ASTM specification which invokes this specification or...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. 16 р. This specification covers a group of common requirements which, unless otherwise specified in the purchase order or in an individual specification, shall apply to carbon and alloy steel bars under each of the ASTM specification which invokes this specification or...
Publisher: ASTM Publish Date: 2015 Pages: 4 Language: English Book of Standards Volume: 01.05 Abstract This specification deals with normalized and tempered, and quenched and tempered, carbon and alloy steel forged or rolled rings for reduction gears. The grades and classes of steels covered here are: Grade 1, Classes A and B, and Grade 2, Classes C and D, which are carbon...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 10, 1998. Published February 1999. 4 p. This specification covers high-carbon bearing-quality steel to be used in the manufacture of anti-friction bearings. Supplementary requirements of an optional nature are provided and when desired shall be so stated in the order
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2008. Published December 2008. Originally approved in 1946. Last previous edition approved in 2008 as A297/A297M – 08. 4 p. This specification covers iron-chromium and iron-chromium-nickel alloy castings for heat-resistant service. The grades covered by this specification are general purpose alloys...
ASTM, 2012, 3p - A302 Standard Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Molybdenum and Manganese-Molybdenum-Nickel. Brief Summary. This specification covers manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates intended particularly for welded boilers and other pressure vessels. According to their strength levels, the plates are...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1947. Last previous edition approved in 2004 as A 304 – 04. 50 p. This specification covers hot-worked alloy, carbon, and carbon-boron steels in a variety of compositions and sizes, which may attain specified depth of hardening in the end quench...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published August 2007. Originally approved in 1947. Last previous edition approved in 2007 as A 307 – 07. 5 p. This specification2 covers the chemical and mechanical requirements of three grades of carbon steel bolts and studs in sizes 1⁄4 in. through 4 in.
American Society for Testing and Materials (ASTM). 2008. 12p. This specification covers seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipe intended for high-temperature and general corrosive service.
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2012. Published May 2012. 12 p. This specification covers seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipe intended for high-temperature and general corrosive service.
Publisher: ASTM Publish Date: 2015 Pages: 13 Language: English Format: PDF Document Scope 1.1 This specification2 covers seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipe intended for high-temperature and general corrosive service. NOTE 1 —When the impact test criterion for a low-temperature service would be 15 ft·lbf [20 J] energy...
[/URL][/img]
Publisher: ASTM
Publish Date: 2015
Pages: 12
Language: English
ISBN: N/A
This specification covers seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipe intended for high-temperature and general corrosive service.
This specification covers alloy steel bolting materials for pressure vessels, valves, flanges, and fittings for low-temperature service. The term bolting material as used in this specification covers rolled, forged, or strain hardened bars, bolts, screws, studs, and stud bolts. The bars shall be hot-wrought. The material may be further processed by centerless grinding or by cold...
Current edition approved May 1, 2017. Published May 2017. This specification covers alloy steel bolting materials and bolting components for pressure vessels, valves, flanges, and fittings for low-temperature service. See Specification A962/A962M for the definition of bolting. The bars shall be hot-wrought and may be further processed by centerless grinding or by cold drawing....
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2011. Published December 2011. Originally approved in 1948. Last previous edition approved in 2011 as A320/A320M–11. 8 p. This specification covers alloy steel bolting for pressure vessels, valves, flanges, and fittings for low-temperature service. See Specification A962/A962M for the definition of...
Publisher: ASTM.
Publish Date: 2015.
Pages: 8.
Language: English.
Format: PDF.
Document Scope .
1.1 This specification covers alloy steel bolting materials.
and bolting components for pressure vessels, valves, flanges,
and fittings for low-temperature service. See Specification.
A962/A962M for the definition of bolting. The bars shall be.
hot-wrought and may be further...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. Published May 2007. Originally approved in 1947. Last previous edition approved in 2006 as A 322 – 06. 4 p. This specification covers hot-wrought alloy steel bars. Bar applications include forging, heat treating, cold drawing, machining and many structural components. The bars shall be...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 15, 1991. Published October 1991. 4 р. This specification covers hot-wrought alloy steel bars. Bar applications include forging, heat treating, cold drawing, machining and many structural components. The bars shall be furnished in the grades specified in Table 1. Sections and sizes of bar steel...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 15, 2007. Published September 2007. Originally approved in 1964. Last previous edition approved in 2006 as A 325 – 06. 8 p. This specification covers two types of quenched and tempered steel heavy hex structural bolts having a minimum tensile strength of 120 ksi for sizes 1.0 in. and less and 105 ksi...
American Society for Testing and Materials (ASTM). 2003, 2p. A 328/A 328M-03
Brief summary
This specification covers carbon steel sheet piling of structural quality for use in the construction of dock walls, sea walls, cofferdams, excavations, and similar applications. When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2011. Published April 2011. 7 p. This specification covers nominal (average) wall seamless and welded carbon and alloy steel pipe intended for use at low temperatures. Several grades of ferritic steel are included as listed in Table
1. Some product sizes may not be available under this...
Issued: 2001
Language: English
Pages: 10
Scope: This specification covers several grades of minimum-wall-thickness, seamless and welded, carbon and alloy-steel tubes intended for use at low temperatures. Some product sizes may not be available under this specification because heavier wall thicknesses have an adverse affect on low-temperature impact properties.
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2004. Published June 2004. Originally approved in 1951. Last previous edition approved in 2004 as A 334/A 334 6M – 04. 6 p. This specification covers several grades of minimum-wall-thickness, seamless and welded, carbon and alloy-steel tubes intended for use at low temperatures. Some product sizes...
American Society for Testing and Materials (ASTM), 2011. — 10 p. This specification covers nominal wall and minimum wall seamless ferritic alloy-steel pipe intended for hightemperature service. Pipe ordered to this specification shall be suitable for bending, flanging (vanstoning), and similar forming operations, and for fusion welding. Selection will depend upon design,...
Publisher: ASTM
Publish Date: 2015
Pages: 10
Language: English
Format: PDF
Document Scope
1.1 This specification2 covers nominal wall and minimum
wall seamless ferritic alloy-steel pipe intended for hightemperature
service. Pipe ordered to this specification shall be
suitable for bending, flanging (vanstoning), and similar forming
operations, and for fusion welding....
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2007. Published May 2007. Originally approved in 1955. Last previous edition approved in 2006 as A 336/A 336M – 06a. 8 p. This specification covers ferritic steel forgings for boilers, pressure vessels, high-temperature parts, and associated equipment. Forgings made of steel grades listed in...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 10, 1999. Published January 2000. 5p. These test methods cover three procedures for determination of the permeability [relative permeability] of materials having a permeability not exceeding 4.0. The test methods covered are as follows: - Test Method 1 is suitable for materials with permeabilities...
This standard is issued under the fixed designation A 350/A 350M; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval. This...
American Society for Testing and Materials (ASTM). 2007. 9 p. This specification covers several grades of carbon and low-alloy steel forged or ring- rolled flanges, forged fittings and valves intended primarily for low-temperature service and requiring notch toughness testing. They are made to specified dimensions, or to dimensional standards, such as the ASME and API...
Стандартные технические условия на стальные поковки из углеродистой и низколегированной стали, подлежащие испытанию на статическую вязкость, для использования в качестве компонентов трубопроводов1 Настоящий стандарт выпущен под постоянным обозначением А 350/А 350М. Номер, следующий непосредственно за обозначением стандарта, указывает на год первоначального принятия стандарта...
This specification2 covers steel castings for valves, flanges, fittings, and other pressure-containing parts intended primarily for low-temperature service
This specification covers steel castings for valves, flanges, fittings, and other pressure-containing parts intended primarily for low-temperature service. Several grades of ferritic steels and one grade of martensitic steel are covered. All castings shall receive a heat treatment proper to their design and chemical composition. It should be recognized that liquid quenching of the...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2009. Published November 2009. 3 р. This specification covers double-normalized and tempered 9 % nickel steel plates intended particularly for welded pressure vessels for cryogenic service. Plates produced under this specification are subject to impact testing at −320°F [−195°C] or at such other...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published August 2007. Originally approved in 1952. Last previous edition approved in 2004 as A 354 – 04. 6 p. This specification covers the chemical and mechanical requirements of quenched and tempered alloy steel bolts, studs, and other externally threaded fasteners 4 in. and under in...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. Originally approved in 1952. Last previous edition approved in 2000 as A 355 – 89 (2000). 3 p. This specification covers alloy steel bars, suitable for surface hardening by nitriding, designated as Classes A, B, C, and D. Class A and Class D bars are general-purpose...
ASTM, 2011, 6p - A356 Standard Specification for Steel Castings, Carbon, Low Alloy, and Stainless Steel, Heavy-Walled for Steam Turbines
Brief Summary
This specification covers one grade of martensitic stainless steel and several grades of ferritic steel castings for cylindrical (shells), valve chests, throttle valves, and other heavy-walled castings for steam turbine...
ASTM, 2012, 8p - A358 Standard Specification for Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless Steel Pipe for High-Temperature Service and General Applications
Brief Summary
This specification covers electric-fusion-welded austenitic chromium-nickel stainless steel pipe suitable for corrosive or high-temperature service, or both, or for general applications. The...
This specification covers carbon steel shapes, plates, and bars of structural quality for use in riveted, bolted, or welded construction of bridges and buildings, and for general structural purposes.
Supplementary requirements are provided for use where additional testing or additional restrictions are required by the purchaser. Such requirements apply only when specified in the...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. 4 р. This specification covers carbon steel shapes, plates,and bars of structural quality for use in riveted, bolted, or welded construction of bridges and buildings, and for general structural purposes.
American Society for Testing and Materials (ASTM). Current edition approved October 1, 2003. Published December 2003. 3 р. This specification covers high-strength, extra-highstrength, and utilities grades of concentric lay steel wire strand composed of three wires or seven wires with Class A, Class B, or Class C zinc coatings specifically intended for use as overhead ground wires...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2006. Published September 2006. Originally approved in 1953. Last previous edition approved in 2002 as A 369/A 369M – 02. 4 p. This specification covers heavy-wall carbon and alloy steel pipe made from turned and bored forgings and is intended for high-temperature service. Pipe ordered under this...
ASTM, 2014, 50p A. 370. Standard Test Methods and Definitions for Mechanical Testing of Steel Products. Scope. These test methods2 cover procedures and definitions for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing...
Американское общество по испытанию материалов - American Society for Testing and Materials (ASTM). 20007. 85 стр. Представленные в данном документе методы испытания содержат процедуры и определения для механических испытаний деформированных и литых изделий из стали, нержавеющей стали и родственных сплавов. Данные механические испытания используются для определения свойств,...
American Society for Testing and Materials (ASTM). Current edition approved June 15, 2010. Published July 2010. 47 р. These test methods cover procedures and definitions for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in...
ASTM A 370-15 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
Publisher: ASTM
Publish Date: 2015
Pages: 50
Language: English
Format: PDF
Document Scope
These test methods cover procedures and definitions
for the mechanical testing of steels, stainless steels, and related
alloys. The various mechanical tests herein described are used...
В настоящем стандарте "Стандартные методы испытаний и определения, применяемые для механических испытаний стальных изделий " приведены процедуры и определения для механических испытаний кованых и литых стальных изделий
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published April 2006. Originally approved in 1954. Last previous edition approved in 2004 as A376/A376M – 04. 7 p. This specification covers seamless austenitic steel pipe intended for high-temperature central-station service. Among the grades covered are five H grades and two nitrogen...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2006. Published May 2006. Originally approved in 1954. Last previous edition approved in 2005 as A 380 – 99 (2005). 13 p. This practice covers recommendations and precautions for cleaning, descaling, and passivating of new stainless stee parts, assemblies, equipment, and installed systems. These...
American Society for Testing and Materials (ASTM). Current edition approved Feb.15, 2013. Published April 2013. Originally approved in 1954. Last previous edition approved in 2006 as A 380 – 06. 13 p. This practice covers recommendations and precautions for cleaning, descaling, and passivating of new stainless stee parts, assemblies, equipment, and installed systems. These...
American Society for Testing and Materials (ASTM). 2001. 7p. This specification covers straight seam, double submerged-are-welded steel pipe suitable for high pressure service, 16 in. (406 mm) and larger in outside diameter, with wall thicknesses from 5/16 to 1 V2 in. (7.9 to 38 mm). The pipe is intended for fabrication of fittings and accessories for compressor or pump-station...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published October 2005. Originally approved in 1954. Last previous edition approved in 2001 as A 381 – 96 (2001). 5 p. This specification covers straight seam, double submerged-are-welded steel pipe suitable for high pressure service, 16 in. (406 mm) and larger in outside diameter, with wall...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1955. Last previous edition approved in 2005 as A 387/A 387M – 05a. 6 p. This specification covers chromium-molybdenum alloy steel plates intended primarily for welded boilers and pressure vessels designed for elevated temperature service.
Approved: April 1, 2011
Published: May 2011
Number of Pages: 9
This practice covers the examination procedures for the contact, pulse-echo ultrasonic examination of heavy steel forgings by the straight and angle-beam techniques. An ultrasonic, pulsed, reflection type of instrument shall be used and shall provide linear presentation for at least 75% of the screen height. The...
American Society for Testing and Materials (ASTM). Current edition approved August 10, 2003. Published September 2003. This specification covers zinc-coated steel chain-link fence fabric, zinc coated either before or after weaving. The values stated in inch-pound units are to be regarded as the standard.
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published August 2007. Originally approved in 1955. Last previous edition approved in 2005 as A 394 – 05. 6 p. This specification covers the chemical and mechanical requirements of hexagon and square-head zinc-coated steel bolts and atmospheric corrosion-resistant bolts, in nominal thread...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published April 2006. Originally approved in 1956. Last previous edition approved in 2000 as A 400 – 69 (2000). 9 p. This practice covers the selection of steel bars according to section and to the mechanical properties desired in the part to be produced. This is not a specification for the...
This specification covers wrought stainless steel fittings for pressure piping applications.
Several grades of austenitic stainless steel alloys are included in this specification, Grades are designated with a prefix, WP or CR, based on the applicable ANSI or MSS dimensional and rating standards, respectively.
For each of the WP stainless grades, several classes of fittings are...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2013. Published October 2013. Originally approved in 1956. Last previous edition approved in 2013 as A403/A403M–13. 9 p. This specification covers wrought stainless steel fittings for pressure piping applications. Several grades of austenitic stainless steel alloys are included in this...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. Published June 2007. Originally approved in 1957. Last previous edition approved in 2004 as A 407 – 93 (2004). 3 p. This specification covers round, cold-drawn, steel spring wire having properties and quality intended for the manufacture of upholstery springs.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published October 2005. Originally approved in 1957 . Last previous edition approved in 2001 as A 409/A 409M – 01. 6 p. This specification covers straight seam or spiral seam electric-fusion-welded, light-wall, austenitic chromium-nickel alloy steel pipe for corrosive or high-temperature...
American Society for Testing and Materials (ASTM). Current edition approved Sept 10, 2002. Published June 2003. 5p. This specification covers two types and two grades of seven-wire, uncoated steel strand for use in pretensioned and post-tensioned prestressed concrete construction. The two types of strand are low-relaxation and stress-relieved (normalrelaxation). Low-relaxation...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2007. Published April 2007. Originally approved in 1958. Last previous edition approved in 2006 as A 420/A 420M – 06. 6 p. This specification covers wrought carbon steel and alloy steel fittings of seamless and welded construction, covered by the latest revision of ASME B 16.9, ASME B 16.11,...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2010. Published December 2010. Originally approved in 1958. Last previous edition approved in 2010 as A420/A420M–10. 6 p. This specification covers wrought carbon steel and alloy steel fittings of seamless and welded construction, covered by the latest revision of ASME B 16.9, ASME B 16.11,...
Обозначение: А 420 / А 420М - 95 Стандартные технические условия на трубопроводные фитинги из кованной углеродистой и легированной стали, используемые в условиях низких рабочих температур1 Настоящий стандарт выпущен под постоянным обозначением А 420/А 420М; номер, следующий непосредственно за обозначением стандарта, указывает на год первоначального принятия стандарта или, в...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. Originally approved in 1958. Last previous edition approved in 2000 as A 424 – 00. 3 p. This specification covers sheet steel in coils and cut lengths for porcelain enameling. The compositions and processing of these steels are such that articles for porcelain enameling...
This specification covers rolled nickel-iron-chromium-molybdenum-copper alloy (UNS N08825 and UNS N08221) plate, sheet, and strip.
The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. Published May 2007. Originally approved in 1958. Last previous edition approved in 2005 as A 426/A 426M - 05. 5 p. This specification covers centrifugally cast alloy steel pipe intended for use in high-temperature, high-pressure service. Several grades of ferritic stee are covered. Their...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2006. Published December 2006. 5 р. This test method covers procedures for determining the weight [mass] of coating on aluminum-coated iron or steel sheets and wire, and on other aluminum-coated iron and steel articles.
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2006. Published May 2006. Originally approved in 1959. Last previous edition approved in 2004 as A 434 – 04. 3 p. This specification covers hot-wrought and cold-finished quenched and tempered alloy steel bars. Hot-wrought bars are available in three strength level classes designated BB, BC, and...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published August 2007. Originally approved in 1963. Last previous edition approved in 2007 as A 449 – 07a. 8 p. This specification covers quenched and tempered steel hex cap screws, bolts, and studs having a minimum tensile strength of 120 ksi for diameters 1.0 in. and smaller; 105 ksi for...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 10, 2003. Published October 2003. Originally approved in 1961. Last previous edition approved in 2002 as A 450/A 450M – 02. 10 p. This specification covers a group of requirements which, with the exceptions of 5.3 and Sections 6, 7, 18, 19, 20, 21, 22, 23, and 24, are mandatory requirements to the...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2006. Published September 2006. Originally approved in 1961. Last previous edition approved in 2002 as A 451/A 451M – 02. 4 p. This specification2 covers austenitic alloy steel pipe for use in high-temperature, corrosive, or nuclear pressure service. Several grades of austenitic stainless steel...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2006. Published May 2006. Originally approved in 1964. Last previous edition approved in 2001 as A 467/A 467M – 01. 4 p. This specification covers welded carbon steel machine chain and coil chain. Although these chains are not intended for pocket wheel use, they can be used for pocket and sprocket...
American Society for Testing and Materials (ASTM). Current edition approved June 15, 2006. Published June 2006. Originally approved in 1962. Last previous edition approved in 2005 as A 471 – 05. 6 p. This specification covers vacuum-treated alloy steel forgings intended for use as turbine rotor disks and wheels. The values stated in inch-pound units are to be regarded as standard.
American Society for Testing and Materials (ASTM). Current edition approved Mar. 10, 2001. Published April 2001. 24p. This specification covers austenitic, austenitic-ferritic, ferritic, and martensitic stainless steel forgings for general use, and for low- or high-temperature service.
This specification covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels for use in boiler and pressure vessel construction.
American Society for Testing and Materials (ASTM). Published 2001. 12 p. This specification covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels for use in boiler and pressure vessel construction.
American Society for Testing and Materials (ASTM). Current edition approved June 15, 2006. Published July 2006. Originally approved in 1962. Last previous edition approved in 2006 as A 479/A 479M – 06. 7 p. This specification covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2008. Published November 2008. 6 р. This specification covers gray iron castings intended for general engineering use where tensile strength is a major consideration. Castings are classified on the basis of the tensile strength of the iron in separately cast test bars. This specification...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2008. Published October 2008. 25p. This specification2 covers a group of general requirements that, unless otherwise specified in the purchase order or in an individual specification, shall apply to rolled steel plate, sheet, and strip, under each of the following specifications issued by ASTM:...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2008. Published October 2008. 25p. This specification covers a group of general requirements that, unless otherwise specified in the purchase order or in an individual specification, shall apply to rolled steel plate, sheet, and strip, under each of the following specifications issued by ASTM:...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1963. Last previous edition approved in 2006 as A 484/A 484M – 06a. 13 p. This specification covers general requirements that shall apply to wrought stainless steel bars, shapes, forgings, and billets or other semi-finished material (except wire)...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2006. Published August 2006. Originally approved in 1964. Last previous edition approved in 2004 as A 490 – 04a. 6 p. This specification covers two types of quenched and tempered, alloy steel, heavy hex structural bolts having a tensile strength of 150 to 173 ksi.
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1963. Last previous edition approved in 2004 as A 498 – 04. 3 p. This specification covers external helical, integral
finned, seamless or welded low-carbon steel tubes for use in tubular heat exchangers, surface condensers, evaporators,...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2010. Published November 2010. 6 p. This specification covers cold-formed welded and seamless carbon steel round, square, rectangular, or special shape structural tubing for welded, riveted, or bolted construction of bridges and buildings, and for general structural purposes. This tubing is...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published April 2006. Originally approved in 1964. Last previous edition approved in 2001 as A 503/A 503M – 01 (2001). 3 p. This is an acceptance specification for the ultrasonic inspection of forged steel crankshafts having main bearing journals or crankpins 4 in. [100 mm] or larger in...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 15, 1993. Published February 1994. Originally published as A 504 – 64 to replace A 57 and A
186. Combined with A 25 in this dition. Last previous edition A 504 –
89. Reapproved 1999. 8 p. This specification covers one-wear, two-wear, and multiple-wear wrought carbon steel wheels for locomotives and...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1964. Last previous edition approved in 2000 as A 505 – 00. 11 p. This specification covers a group of common requirements that, unless otherwise specified in the material specification, apply to hot-rolled and cold-rolled alloy steel sheet and...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2005. Published December 2005. Originally approved in 1964. Last previous edition approved in 2004 as A 506 – 04. 4 p. This specification covers hot-rolled and cold-rolled
alloy and structural alloy-steel sheet and strip. Alloy steel is furnished to chemical composition requirements and is...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. Originally approved in 1964. Last previous edition approved in 2005 as A 507 – 05. 4 p. This specification covers hot-rolled and cold-rolled drawing alloy-steel sheet and strip. Material of this quality is produced principally for applications involving severe cold...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published October 2005. Originally approved in 1964. Last previous edition approved in 2005 as A 508/A 508M – 05a. 9 p. This specification covers quenched and tempered vacuum-treated carbon and alloy steel forgings for pressure vessels such as those used in reactor systems. Specifically, it...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published September 2007. Originally approved in 1964. Last previous edition approved in 2006 as A 510 – 06.7 p. This specification covers general requirements for carbon steel wire rods and uncoated coarse round wire in coils or straightened and cut lengths.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2006. Published September 2006. Originally approved in 1977. Last previous edition approved in 2003 as A 510M – 03. 7 p. This specification covers general requirements for carbon steel wire rods and uncoated coarse round wire in coils or straightened and cut lengths.
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2012. Published April 2012. 11 p. This specification covers seamless stainless tubing for use in mechanical applications where corrosion-resistant or high-temperature strength is needed. The grades covered are listed in Table 1, Table 2, and Table 3. This specification covers seamless...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1964. Last previous edition approved in 2005 as A 512 – 96 (2005). 7 p. This specification covers cold-drawn buttweld carbon steel tubes for use as mechanical tubing. This specification covers round, square, rectangular, and special shape...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2012. Published July 2012. 20 p. This specification covers electric-resistance-welded carbon and alloy steel tubing for use as mechanical tubing. This specification covers mechanical tubing made from hot- or cold-rolled steel. This specification covers round, square, rectangular, and special...
American Society for Testing and Materials (ASTM). 2000, 3p. A 514/A 514M-00a
Brief summary
This specification covers high-yield, quenched, and tempered alloy steel plates for use in welded bridges and other structures. Plates shall be subjected to heat treatment to conform to the tensile and hardness requirements for thickness, tensile strength, yield strength, elongation,...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published October 2005. Originally approved in 1964. Last previous edition approved in 2000 as A 514/A 514M – 00a. 3 p. This specification covers quenched and tempered alloy steel plates of structural quality in thicknesses of 6 in. [150 mm] and under intended primarily for use in welded...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2010. Published November 2010. Originally approved in 1964. Last previous edition approved in 2007 as A515/A515M – 03 (2007). 4 p. This specification covers carbon-silicon steel plates primarily for intermediate- and higher-temperature service in welded boilers and other pressure vessels.
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. Originally approved in 1964. Last previous edition approved in 2005 as A 516/A 516M – 05. 4 p. This specification covers carbon steel plates intended primarily for service in welded pressure vessels where improved notch toughness is important.
American Society for Testing and Materials (ASTM). 2004, 3p. A 516/A 516M
Brief Summary
This specification covers carbon steel plates intended primarily for service in welded pressure vessels where improved notch toughness is important. According to different strength levels, the plates are available in four grades: Grades 55, 60, 65, and
70. The maximum thickness of plates is...
Publisher: ASTM Publish Date: 2015 Pages: 3 Language: English Format: PDF Document Scope 1.1 This specification2 covers high-strength quenched and tempered alloy steel plates intended for use in fusion welded boilers and other pressure vessels. 1.2 This specification includes a number of grades as manufactured by different producers, but all having the same mechanical...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. 13 p. This specification covers several grades of carbon and alloy steel seamless mechanical tubing. The grades are listed in Tables 1-
3. When welding is used for joining the weldable mechanical tube grades, the welding procedure shall be suitable for the grade, the...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2007. Published April 2007. Originally approved in 1964. Last previous edition approved in 2006 as A 522/A 522M – 06. 4 p. This specification covers 8 and 9 % nickel-alloy steel forged or rolled flanges, fittings, valves, and parts intended for use in welded pressure vessels for low-temperature...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published November 2005. Originally approved in 1964. Last previous edition approved in 2001 as A 523 – 96 (2001). 5 p. This specification covers seamless and electricresistance-welded steel pipe used as conduit for the installation of high-pressure pipe-type electrical cables in NPS 4 to NPS...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published November 2005. Originally approved in 1965. Last previous edition approved in 2001 as A 524 – 96 (2001). 8 p. This specification covers seamless carbon steel pipe intended primarily for service at atmospheric and lower temperatures, NPS 1⁄8 to 26 inclusive, with nominal (average)...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1964. Last previous edition approved in 2004 as A 529/A 529M – 04. 3 p. This specification covers carbon-manganese steel shapes, plates, and bars of structural quality for use in riveted, bolted, or welded construction of buildings and for general...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2010. Published November 2010. 22 р. This specification covers seamless and welded black and hot-dipped galvanized steel pipe in NPS 1⁄8 to NPS 26 [DN 6 to DN 650], inclusive, with nominal wall thickness as given in Table X2.2 and Table X
2.3. It shall be permissible to furnish pipe having other...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2012. Published April 2012. Originally approved in 1915. Last previous edition approved in 2010 as A53/A53M–10. 23 p. This specification covers seamless and welded black and hot-dipped galvanized steel pipe in NPS 1⁄8 to NPS 26 [DN 6 to DN 650], inclusive, with nominal wall thickness as given in...
Настоящая спецификация распространяется на бесшовные и сварные черные и оцинкованные горячим погружением стальные трубы размерами от NPS 1/8 до NPS 26 [от DN 6 до DN 650] (Примечание 1), включительно, с номинальной толщиной стенки (Примечание 2), приведенной в таблице X2.2 и таблице X2.3.
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published April 2006. Originally approved in 1965. Last previous edition approved in 2001 as A 531/A 531M – 91 (2001).5 p. This practice covers the procedures to be followed when performing ultrasonic shear and longitudinal wave tests on -generator retaining rings with an inside diameter...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2008. Published November 2008. Originally approved in 1965. Last previous edition approved in 2003 as A532/A532M – 93a. 4 p. This specification covers a group of white cast irons that have been alloyed to secure high resistance to abrasive wear in the applications of the mining, milling,...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2009. Published August 2009. 5 p. This specification covers castings made of ductile iron, also known as spheroidal or nodular iron, that is described as cast iron with the graphite substantially spheroidal in shape and essentially free of other forms of graphite, as defined in Terminology A644.
American Society for Testing and Materials (ASTM). Current edition approved June 15, 1995. Published August 1995. Reapproved 2000. 4 р. This specification covers heat-treated carbonmanganese-silicon steel plates intended for fusion welded pressure vessels and structures. The maximum thickness of plates furnished under this specification is 4 in. [100 mm] for Class 1 and 6 in....
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. Originally approved in 1965. Last previous edition approved in 2005 as A 540/A 540M – 05. 8 p. This specification covers regular and special-quality alloy steel bolting materials which may be used for nuclear and other special applications. Bolting materials as used in...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1965. Last previous edition approved in 2004 as A 541/A 541M – 04. 6 p. This specification covers requirements for quenched and tempered carbon and alloy steel forgings for pressure vessel components. All grades are considered weldable under...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2008. Published October 2008. Originally approved in 1965. Last previous edition approved in 2008 as A 554 – 08. 6 p. This specification covers welded stainless steel tubing for mechanical applications where appearance, mechanical properties, or corrosion resistance is needed. The grades covered...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 10, 2003. Published October 2003. Originally approved in 1965. Last previous edition approved in 1998 as A 554 – 98. 6 p. This specification covers welded stainless steel tubing for mechanical applications where appearance, mechanical properties, or corrosion resistance is needed.
American Society for Testing and Materials (ASTM). Current edition approved October 1, 2005. Published November 2005. Originally approved in 1965. Last previous edition approved in 2001 as A 556/A 556M – 96 (2001). 5 p. This specification covers minimum-wall-thickness, seamless cold-drawn carbon steel tubes including bending into the form of U-tubes, if specified, for use in...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published August 2007. Originally approved in 1966. Last previous edition approved in 2004 as A 563 – 04a. 8 p. This specification covers chemical and mechanical requirements for eight grades of carbon and alloy steel nuts for general structural and mechanical uses on bolts, studs, and other...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2004. Published March 2004. 8 р. This specification covers bars and shapes of agehardening stainless steels. Hot-finished or cold-finished rounds, squares, hexagons, bar shapes, angles, tees, and channels are included; these shapes may be produced by hot rolling, extruding, or forging. Billets or...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1966. Last previous edition approved in 2005 as A 565 – 05. 4 p. This specification covers hot-finished and cold-finished martensitic chromium steel bars for high-temperature service. The mechanical properties are developed by suitable heat...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published September 2007. Originally approved in 1966. Last previous edition approved in 2006 as A 568/A 568M – 06a. 29 p. This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel,...
American Society for Testing and Materials (ASTM). 2004, 4p. A 572/A 572M-04
Brief summary
This specifiation covers the standard requirements for Grades 42 [290], 50 [345], 55 [380], 60 [415], and 65 [450] of high-strength low-alloy columbium-vanadium structural steel shapes, plates, sheet piling, and bars for applications in bolted, welded, and riveted structures in bridges and...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2007. Published March 2007. Originally approved in 1966. Last previous edition approved in 2006 as A 572/A 572M – 06. 4 p. This specification covers five grades of high-strength low-alloy structural steel shapes, plates, sheet piling, and bars. Grades 42 [290], 50 [345], and 55 [380] are intended...
American Society for Testing and Materials (ASTM). 2000, 2p. A 573/A 573M-00a
Brief summary
This specification covers structural quality carbon-manganese-silicon steel plates in three tensile strength ranges intended primarily for service at atmospheric temperatures where improved notch toughness is important. If the steel is to be welded, a welding procedure suitable for the...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. Originally approved in 1967. Last previous edition approved in 2000 as A 576 – 90b (2000). 5 p. This specification covers hot-wrought special quality carbon steel bars. Special quality bar applications include forging, heat treating, cold drawing, machining, and many...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. 4 р. This specification covers Stainless steel wire, excert the free-machining types. It includes round, square, octagon, hexagon, and shape wire in coils only for the more commonly used types of stainless steels for general corrosion resistance and high-temperature...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. 3 р. This specification covers hot-finished or cold-finished bars, except bars for forging, suitable for machining processes. It includes rounds, squares, and hexagons in the more commonly used types of stainless free-machining steels designed especially for optimum...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published November 2005. Originally approved in 1968. Last previous edition approved in 2001 as A 587 – 96 (2001). 6 p. This specification covers electric-resistance-welded low-carbon steel pipe intended for use as process lines. Pipe ordered under this specification shall be suitable for...
American Society for Testing and Materials (ASTM). 2004, 3p. A 588/A 588M-04 Brief summary This specification covers high-strength, low-alloy structural steel shapes, plates, and bars for welded, riveted, or bolted construction with atmospheric corrosion resistance. Heat analysis shall be performed wherein the low-alloy structural steel materials shall conform to the required...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2005. Published April 2005. Originally approved in 1968. Last previous edition approved in 2004 as A 588/A 588M – 04. 3 p. This specification covers high-strength low-alloy structural steel shapes, plates, and bars for welded, riveted, or bolted construction but intended primarily for use in...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published April 2006. Originally approved in 1968. Last previous edition approved in 2001 as A 589 – 96(2001). 12 p. This specification covers four specific types of plain end or threaded and coupled carbon steel pipe for use in water wells.
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. Originally approved in 1969. Last previous edition approved in 2004 as A 595 – 04a. 5 p. This specification covers three grades of seam-welded, round, tapered steel tubes for structural use. GradesAand B are of low-carbon steel or high-strength low-alloy steel...
American Society for Testing and Materials (ASTM). 2004, 64p. A 6/A 6M-04a
Brief summary
This specification deals with the general requirements that apply to rolled structural steel bars, plates, shapes, and sheet piling. The steel shall be made in an open-hearth, basic-oxygen, or electric-arc furnace followed by additional refining in a ladle metallurgy furnace, or secondary...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2007. Published March 2007. Originally approved in 1949. Last previous edition approved in 2006 as A 6/A 6M – 06. 59 p. This general requirements specification covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled structural...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2004. Published Jan. 2005. 14 р. This specification covers tungsten-type and molybdenum-type high-speed steels available as annealed, hot-rolled bars, forgings, plate, sheet, or strip, and annealed, cold-finished bars or forgings used primarily in the fabrication of tools
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. Published June 2007. Originally approved in 1970. Last previous edition approved in 2003 as A 604 – 93 (2003). 15 p. This practice covers testing and inspection and is applicable to bars, billets, and blooms of carbon, alloy, and stainless steel which have been consumable electrode remelted.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2006. Published September 2006. Originally approved in 1970. Last previous edition approved in 2002 as A 608/A 608M – 02. 6 p. This specification covers iron-chromium-nickel, high-alloy tubes made by the centrifugal casting process intended for use under pressure at high temperatures.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2009. Published December 2009. 6 p. This specification covers deformed and plain carbonsteel bars for concrete reinforcement in cut lengths and coils. Steel bars containing alloy additions, such as with the American Iron and Steel Institute and the Society of Automotive Engineers series of alloy...
American Society for Testing and Materials (ASTM). 2001, 5p. A 633/A 633M-01
This specification covers normalized high-strength low-alloy structural steel plates for welded, riveted, or bolted construction. This material is suited for low ambient temperatures where the desired notch toughness is better than that expected in as-rolled materials of comparable strength level. The...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published September 2007. Originally approved in 1970. Last previous edition approved in 2006 as A 635/A 635M – 06a. 11 p. This specification covers the general requirements for hot-rolled, heavy-thickness sheet and strip in coils. It applies to Specification A 1018/A 1018M.
American Society for Testing and Materials (ASTM). Current edition approved October 1, 2003. Published December 2003. 5 р. This specification covers soft, medium, and hard temper zinc-coated (galvanized) carbon steel wire in coils for general use. The supplementary requirements of this specification cover zinc-coated weights [masses] for nails, staples, and wire from which...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2005. Published June 2005. 12p. This specification covers steel sheet, zinc-coated (galvanized) or zinc-iron alloy-coated (galvannealed) by the hotdip process in coils and cut lengths. The product is available in a number of designations, grades and classes in four general categories that are...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2006. Published January 2007. 13 р. This specification covers steel sheet, zinc-coated (galvanized) or zinc-iron alloy-coated (galvannealed) by the hotdip process in coils and cut lengths. Product furnished under this specification shall conform to the applicable requirements of the latest issue...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2009. Published June 2009. 15 p. This specification covers steel sheet, zinc-coated (galvanized) or zinc-iron alloy-coated (galvannealed) by the hot-dip process in coils and cut lengths. Product furnished under this specification shall conform to the applicable requirements of the latest issue of...
American Society for Testing and Materials (ASTM). 2003, 2p. A 656/A 656M-03
This specification covers the three types and four strength grades of high strength low-alloy, hot rolled structural steel plate with improved formability. These steels are normally furnished in the as-rolled condition. For plates produced from coil, and furnished without heat treatment or with stress...
American Society for Testing and Materials (ASTM). Current edition approved April 10, 2003. Published June 2003. Originally published in 1972. Last previous edition approved in 2000 as A 656/A 656M – 00a. 2 p. This specification covers two types and four strength grades of high-strength low-alloy, hot rolled structural steel plate for use in truck frames, brackets, crane booms,...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1972. Last previous edition approved in 2001 as A 659/A 659M – 97 (2001). 3 p. This specification covers hot-rolled carbon steel (CS) sheet and strip, in coils and cut lengths, in which the maximum of the specified carbon range is over 0.15 and...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published April 2006. Originally approved in 1972. Last previous edition approved in 2000 as A 663/A 663M – 89 (2000). 3 p. This specification covers hot-wrought merchant quality carbon steel bars and bar size shapes produced to mechanical property requirements and intended for noncritical...
ASTM, 2014, 7p. A 671/ 671M, Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures Brief Summary This specification covers standard requirements for electric-fusion-welded steel pipe with filler metal added, for atmospheric and lower temperatures. The steel pipe shall be fabricated from a pressure vessel quality plate of several...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2004. Published May 2004. 9 р. This specification covers electric-fusion-welded steel pipe with filler metal added, fabricated from pressure vessel quality plate of several analyses and strength levels and suitable for high-pressure service at atmospheric and lower temperatures. Heat treatment mayor...
ASTM, 2014, 7p. A 672/ 672M, Standard Specification for Electric-Fusion-Welded Steel Pipe for High-Pressure Service at Moderate Temperatures This specification covers electrical-fusion-welded steel pipe for high-pressure service at moderate temperatures. Heat treatment may or may not be required to attain the desired properties or to comply with applicable code requirements. An...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2006. Published May 2006. Originally approved in 1973. Last previous edition approved in 2000 as A 679/A 679M – 00. 4 p. This specification covers round, uncoated, high tensile strength, cold-drawn steel spring wire, having properties and quality suitable for the manufacture of mechanical springs...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2008. Published October 2008. 14 р. This specification covers the chemical, mechanical, and physical requirements for available wrought alloy tool steel products. These products, which include hot or cold finished bar, plate, sheet, strip, rod, wire, or forgings, are normally fabricated into...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2005. Published December 2005. Originally approved in 1973. Last previous edition approved in 2002 as A 682/A 682M – 02. 8 p. This specification covers the general requirements for cold-rolled carbon spring steel strip in coils or cut lengths. Strip is classified as product that is 0.3000 in. (7.6...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1973. Last previous edition approved in 2002 as A 684/A 684M – 86 (2002). 4 p. This specification covers cold-rolled, high-carbon strip. It is furnished in the following types as specified. Soft spheroidized annealed high-carbon steel is...
1. Scope 1.1 This specification2 covers welded austenitic stainless steel feedwater heater tubes including those bent, if specified, into the form of U-tubes for application in tubular feed-water heaters. 1.2 The tubing sizes covered shall be 5⁄8 to 1 in. [15.9 to 25.4 mm] inclusive outside diameter, and average or minimum wall thicknesses of 0.028 in. [0.7 mm] and heavier. 1.3...
1. Scope 1.1 This specification2 covers welded austenitic stainless steel feedwater heater tubes including those bent, if specified, into the form of U-tubes for application in tubular feed-water heaters. 1.2 The tubing sizes covered shall be 5⁄8 to 1 in. [15.9 to 25.4 mm] inclusive outside diameter, and average or minimum wall thicknesses of 0.028 in. [0.7 mm] and heavier. 1.3...
1. Scope * 1.1 This specification2 covers welded austenitic stainless steel feedwater heater tubes including those bent, if specified, into the form of U-tubes for application in tubular feed-water heaters. 1.2 The tubing sizes covered shall be 5⁄8 to 1 in. [15.9 to 25.4 mm] inclusive outside diameter, and average or minimum wall thicknesses of 0.028 in. [0.7 mm] and heavier....
1. Scope* 1.1 This specification2 covers welded austenitic stainless steel feedwater heater tubes including those bent, if specified, into the form of U-tubes for application in tubular feed-water heaters. 1.2 The tubing sizes covered shall be 5⁄8 to 1 in. [15.9 to 25.4 mm] inclusive outside diameter, and average or minimum wall thicknesses of 0.028 in. [0.7 mm] and heavier....
1. Scope* 1.1 This specification2 covers welded austenitic stainless steel feedwater heater tubes including those bent, if specified, into the form of U-tubes for application in tubular feed-water heaters. 1.2 The tubing sizes covered shall be 5⁄8 to 1 in. [15.9 to 25.4 mm] inclusive outside diameter, and average or minimum wall thicknesses of 0.028 in. [0.7 mm] and heavier....
American Society for Testing and Materials (ASTM). 2000, 2p. A 690/A 690M-00a
This specification deals with the standard structural quality of high-strength low-alloy nickel, copper, phosphorus steel H-piles and sheet piling for use in the construction of dock walls, bulkheads, excavations, and like applications in marine environments. The steel shall be semi-killed or killed and...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. Originally approved in 1974. Last previous edition approved in 2003 as A 693 – 03. 9 p. This specification covers precipitation-hardening stainless steel plate, sheet, and strip. The mechanical properties of these steels are developed by suitable low-temperature heat...
Issue: 1999
Language: English
Pages: 3
Scope:
This specification covers forged or rolled steel pipe flanges, forged fittings, valves, and parts suitable for use with high-strength transmission-service pipe. They are made to specified dimensions, or to dimensional standards, such as the ASME and MSS specifications referenced in Section 1.2.
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2008. Published November 2008. Originally approved in 1974. Last previous edition approved in 2003 as A 694/A 694M – 03. 4 p. This specification covers forged or rolled steel pipe flange, forged fittings, valves, and parts suitable for use with high-strength transmission-service pipe. Included are...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. Originally approved in 1974. Last previous edition approved in 2000 as A 696 – 90a (2000). 3 p. This specification covers hot-wrought and cold-finished special quality carbon steel bars, in straight lengths only, subject to mechanical property requirements and intended...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 7, 1989. Published February 1990. 4 р. This specification covers steel fence posts and assemblies manufactured from hot-wrought sections and intended for use in field and line fencing. The posts are available in tee, channel, or U and Y-bar shapes or angle shapes and are furnished painted or...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. Originally approved in 1974. Last previous edition approved in 2000 as A 702 – 89 (2000). 4 p. This specification covers steel fence posts and assemblies manufactured from hot-wrought sections and intended for use in field and line fencing. The posts are available in...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 10, 2002. Published November 2002. Originally published as A 707 –
74. Last previous edition A 707/A 707M – 00a. 5 p. This specification covers forged carbon and alloy steel flanges intended primarily for petroleum and gas pipelines in areas subject to low ambient temperatures. Included are flanges...
American Society for Testing and Materials (ASTM). Current edition approved March 15, 2006. Published March 2006. Originally approved in 1974. Last previous edition approved in 2005 as A 709/A 709M– 05. 8 p. This specification covers carbon and high-strength lowalloy steel structural shapes, plates, and bars and quenched and tempered alloy steel for structural plates intended for...
Publisher: ASTM Publish Date: 2015 Pages: 5 Language: English Format: PDF Document Scope 1.1 This specification covers the requirements for welded and seamless carbon steel pipe nipples, black and zinc-coated (hot-dip galvanized), and welded and seamless austenitic stainless steel pipe nipples in standard steel pipe sizes from 1⁄8 to 12 in. inclusive, in standard or special...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. Originally approved in 1976. Last previous edition approved in 2000 as A 739 – 90a (2000). 2 p. This specification covers hot-wrought, ferritic alloy steel bars for elevated temperature or pressure-containing parts suitable for fusion welding or both.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2008. Published December 2008. Originally approved in 1977. Last previous edition approved in 2003 as A 742/A 742M – 03. 4 p. This specification covers polymer precoated steel sheet for corrugated steel pipe (CSP) which is coated after metallic coating on continuous lines by coil coating (roller...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. Originally approved in 1977. Last previous edition approved in 2003 as A743/A743M – 03. 7 p. This specification covers iron-chromium and ironchromium-nickel alloy castings for general corrosion-resistant application. The grades covered by this specification represent...
ASTM, 2013, 8p. A743 / A743M. Standard Specification for Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion Resistant, for General Application
Brief Summary
This specification covers iron-chromium and iron-chromium-nickel alloy castings for general corrosion-resistant application. The grades of these castings represent types of alloy castings suitable for broad ranges of...
ASTM, 2013, 4p. ASTM A744 / A744M. Standard Specification for Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Severe Service
Brief Summary
This specification covers standard requirements for iron-chromium-nickel alloy, stainless steel castings intended for particularly severe corrosive applications. Alloys shall be melted by the electric furnace process with or without...
ASTM 1999, 4p. A 747/A747M Standard Specification for Steel Castings, Stainless, Precipitation Hardening Brief Summary This specification covers iron-chromium-nickel-copper corrosion resistance steel castings capable of being strengthened by precipitation hardening heat treatment. The steel shall be made by electric furnace process with or without separate refining such as...
Американский стандарт определяет нормированные методы химического анализа стальной продукции (обычные углеродистые и нержавеющие марки сталей и сплавы на их основе), определяет методологию, ссылочные материалы и технику проведения анализов. This standard covers definitions, reference methods, practices, and guides relating to the chemical analysis of steel, stainless steel, and...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2007. Published June 2007. Originally approved in 1977. Last previous edition approved in 2007 as A 751 – 07. 6 p. These test methods, practices, and terminology cover definitions, reference methods, practices, and guides relating to the chemical analysis of steel, stainless steel, and related...
Настоящий стандарт рассматривает определения, образцовые методы и процедуры, имеющие отношение к химическому анализу стали, нержавеющей стали и соответствующих сплавов. Сюда относятся как мокрые "методы" химического анализа, так и методы с применением инструментальных средств.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 10, 2000. Published December 2000. Originally approved in 1978. Last previous edition approved in 1998 as A 758/A 758M – 98. 5 p. This specification covers wrought-carbon steel buttwelding seamless or welded fittings specially processed to ensure better notch toughness than that to be expected in...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2010. Published October 2010. Originally approved in 1979. Last previous edition approved in 2009 as A760/A760M - 09. 15 p. This specification covers corrugated steel pipe intended for use for storm water drainage, underdrains, the construction of culverts, and similar uses. Pipe covered by this...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2009. Published January 2010. Originally approved in 1979. Last previous edition approved in 2004 as A761 – 04. 8 p. This specification covers corrugated steel structural plate, zinc-coated, used in the construction of pipe, pipearches, arches, underpasses, and special shapes for field assembly....
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2008. Published June 2008. Originally approved in 1979. Last previous edition approved in 2000 as A 762/A 762M – 00. 10 p. This specification covers polymer precoated corrugated steel pipe intended for use for storm water drainage, underdrains, the construction of culverts, and similar uses. Pipe...
ASTM 1993 (Reapprived 2004), 11p. A 763 Standard Practices for Detecting Susceptibility to Intergranular Attack in Ferritic Stainless Steels This practices covers the detecting susceptibility to intergranular attack in ferritic stainless steel. Different method of preparing steel test specimens are presented. Four practices, including Practice W, X, Y, and Z, are used for...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2007. Published March 2007. Originally approved in 1979. Last previous edition approved in 2001 as A 764 – 95 (2001). 5 p. This specification covers two finishes of round, metallic coated, hard-drawn, carbon steel spring wire having properties and quality for the manufacture of mechanical springs...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published October 2007. Originally approved in 1979. Last previous edition approved in 2004 as A 765/A 765M – 04. 5 p. This specification covers heat-treated carbon steel and alloy steel forgings with mandatory toughness requirements. These forgings are intended for pressure vessels,...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. Originally approved in 1980. Last previous edition approved in 2002 as A 774/A 774M – 02. 4 p. This specification covers five grades of as-welded, wrought austenitic stainless steel fittings for low-pressure piping and intended for low and moderate temperatures and...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1981. Last previous edition approved in 2001 as A 787 – 01. 7 p. This specification covers round, square, rectangular, and special shape, electric-resistance-welded mechanical tubing, either zinc-coated (galvanized) after welding or produced from...
American Society for Testing and Materials (ASTM). 2001. 4p. This specification covers grades of nominal wall thickness, stainless steel tubing for services requiring general corrosion resistance, with particular emphasis on resistance to stress corrosion cracking. These steels are susceptible to embrittlement if used for prolonged periods at elevated temperatures
American Society for Testing and Materials (ASTM). Current edition approved September 1, 2005. Published September 2005. Originally approved in 1981. Last previous edition approved in 2005 as A 789/A 789M–05a. 5 p. This specification covers grades of nominal wall thickness, stainless steel tubing for services requiring general corrosion resistance, with particular emphasis on...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2005. Published June 2005. Originally approved in 1981. Last previous edition approved in 2005 as A 790/A 790M–05. 8 p. This specification covers seamless and straight-seam welded ferritic/austenitic steel pipe intended for general corrosive service, with particular emphasis on resistance to stress...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published October 2007. Originally approved in 1981. Last previous edition approved in 2005 as A 790/A 790M – 05b. 8 p. This specification2 covers seamless and straight-seam welded ferritic/austenitic steel pipe intended for general corrosive service, with particular emphasis on resistance...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1982. Last previous edition approved in 2002 as A 794 – 97 (2002). 3 p. This specification covers cold-rolled commercial steel (CS) sheet in coils and cut lengths, in which the maximum of the specified carbon range is over 0.15 and not over 0.25...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 10, 2000. Published November 2000. Originally published as A 795 –
82. Last previous edition A 795 – 97. 6 p. This specification covers black and hot-dipped galvanized welded and seamless steel pipe in sizes NPS 1/2 (Note 1) to NPS 10 inclusive, with wall thicknesses as given in Table 1 and Table...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2010. Published January 2011. Originally approved in 1982. Last previous edition approved in 2006 as A796/A796M - 06. 22 p. This practice covers the structural design of corrugated steel pipe and pipe-arches, ribbed and composite ribbed steel pipe, ribbed pipe with metallic-coated inserts, closed...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 15, 2007. Published October 2007. Originally approved in 1982. Last previous edition approved in 2001 as A 798/A 798M - 01. 6 p. This practice covers procedures, soils, and soil placement for the proper installation of corrugated steel pipe and pipe-arches produced to Specification A 760/A 760M or A...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2008. Published December 2008. Originally approved in 1982. Last previous edition approved in 2002 as A 807/A 807M - 02. 7 p. This practice covers procedures, soils, and soil placement for the proper installation of corrugated steel structural plate pipe, pipe-arches, arches, and underpasses...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published October 2007. Originally approved in 1983. Last previous edition approved in 2005 as A 813/A 813M – 01(2005). 8 p. This specification covers two classes of fit-up and alignment quality straight-seam single- or double-welded austenitic steel pipe intended for high-temperature and...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published October 2007. Originally approved in 1983. Last previous edition approved in 2005 as A 814/A 814M – 05. 6 p. This specification covers two classes of flanged and cold-bending quality cold-worked straight-seam single or double welded austenitic steel pipe intended for...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published October 2007. Originally approved in 1983. Last previous edition approved in 2007 as A 815/A 815M – 07. 7 p. This specification covers two general classes, WP and CR, of wrought ferritic, ferritic/austenitic, and martensitic stainless steel fittings of seamless and welded...
American Society for Testing and Materials (ASTM). Current edition approved April 10, 2003. Published May 2003. 4 р. This specification covers metallic-coated carbon steel wire used in the manufacture of chain-link fence fabric and marcelled tension wire. Three types of coatings are covered: Type I—Aluminum-coated (aluminized), Type II—Zinc-coated (galvanized), and Type...
Данные ТУ распространяются на стальную проволоку холодного проката, в холоднотянутом состоянии или оцинкованную, для применения в указанном качестве или в собранном виде, для укрепления железобетона, номинальным диаметром не менее 0.080 дюймов (2.03-мм).
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2007. Published April 2007. Originally approved in 1984. Last previous edition approved in 2002 as A 836/A 836M – 02. 2 p, This specification covers nonstandard as-forged fittings, valve components, and parts for glass-lined piping and pressure vessel service. Mechanical properties are certified...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2010. Published January 2011. Originally approved in 1985. Last previous edition approved in 2005 as A849 - 00(2005). 8 p. This specification covers post-applied coatings, pavings, and linings for corrugated steel pipe and corrugated steel structural plate pipe, pipe-arches, and arches coated,...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2009. Published August 2009. 4 р. This specification covers soft, medium, and hard temper zinc-5 % aluminum-mischmetal (Zn-5 Al-MM) alloy-coated carbon steel wire in coils for general use. The product is intended for applications requiring corrosion resistance, drawability, and formability.
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2007. Published April 2007. Originally approved in 1986. Last previous edition approved in 2006 as A 858/A 858M – 06. 4 p. This specification covers heat-treated wrought carbon steel piping fittings with lowered carbon content of seamless and electric fusion-welded construction covered by the...
American Society for Testing and Materials (ASTM). Current edition approved 2010. Originally approvedin1986. 7 p. This specification covers wrought high – strength ferritic steel butt-welding fitting of seamless and electric and fusion-welded construction covered by the latest revision of ASME B16.9 and MSS-SP-75 . Butt-welding fittings differing from these ASME and MSS...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2010. Published December 2010. Originally approved in 1986. Last previous edition approved in 2009 as A860/A860M–09. 5 p. This specification covers wrought high – strength ferritic steel butt-welding fitting of seamless and electric and fusion-welded construction covered by the latest revision of...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2008. Published July 2008. Originally approved in 1986. Last previous edition approved in 2003 as A 862/A 862M - 98(2003). 3 p. This practice covers the post coating of corrugated steel pipe and corrugated structural steel plate with asphalt materials. This practice is intended for shop-applied...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2007. Published April 2007. Originally approved in 1977. Last previous edition approved in 2007 as A 872/A 872M – 07. 4 p. This specification covers centrifugally cast ferritic/
austenitic steel pipe intended for general corrosive service. These steels are susceptible to embrittlement if used for...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1987. Last previous edition approved in 1999 as A 877/A 877M – 99. 4 p. This specification covers the highest quality of round chromium-silicon alloy steel valve spring wire, uniform in quality and temper, intended for the manufacture of valve...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1987. Last previous edition approved in 1999 as A 878/A 878M – 99. 4 p. This specification covers the highest quality of round modified chromium vanadium alloy steel valve spring wire, uniform in quality and temper, intended for the manufacture of...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. Published May 2007. Originally approved in 1988. Last previous edition approved in 2003 as A 891 – 98 (2003). 3 p. This specification covers precipitation hardening iron base superalloy forgings which are primarily intended for use as turbine rotor disks and wheels. Two heat treatments are...
ASTM, 2012, 5p A890 Standard Specification for Castings, Iron-Chromium-Nickel-Molybdenum Corrosion-Resistant, Duplex (Austenitic/Ferritic) for General Application Brief Summary This specification covers castings, iron-chromium-nickel-molybdenum corrosion-resistant, duplex(austenitic/ferritic) for general application. Castings shall be heat treated in accordance with the...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2006. Published September 2006. Originally approved in 1988. Last previous edition approved in 2001 as A 892 – 88 (2001). 5 p. This guide covers the description of carbide structures in annealed high carbon bearing steels. Included is a guide for rating steel specimens by a graded series of...
American Society for Testing and Materials (ASTM). Reapproved 1999. 4p. This test method covers procedures for determining the weight [mass] of coating on iron or steel sheet, wire, and other articles in which the coating is zinc or a zinc alloy, such as zinc-5 % aluminum (including zinc-5 % aluminummischmetal and zinc-5 % aluminum-0.1 % magnesium) or 55 % aluminum-zinc. In the...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. December 2006. Originally approved in 1992. Last previous edition approved in 2003 as A 909 – 03. 4 p. This specification covers wrought, microalloyed carbon steel forgings for industrial use. Microalloyed steels develop their properties by the addition of small amounts of microalloying...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1992. Last previous edition approved in 1999 as A 914/A 914M -92(1999). 27 p. This specification covers hot-worked alloy and carbonboron steels designed to attain restricted depth of hardening in the end-quench test. These steel compositions are...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1993. Last previous edition approved in 1999 as A 921/A 921M - 93(1999). 3 p. This specification covers hot-wrought, special quality microalloyed carbon steel bars intended for use as hot forging stock. The bars shall be hot-wrought, as-wrought,...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2010. Published May 2010. Originally approved in 1993. Last previous edition approved in 2005 as A922-05. 2p. This specification covers several grades of silicon metal. The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2006. Published May 2006. Originally approved in 1994. Last previous edition approved in 2003 as A 923 – 03. 10 p. The purpose of these test methods is to allow detection of the presence of intermetallic phases in duplex stainless steels to the extent that toughness or corrosion resistance is...
American Society for Testing and Materials (ASTM). Current edition approved .May 1,
.2009. Published .June 2009. 14 p. This specification covers the general requirements that, unless otherwise specified in the product specification, apply to steel sheet in coils and cut lengths, metallic-coated on continuous lines by the hot-dip process. The product is intended for applications...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2008. Published July 2008. Originally approved in 1994. Last previous edition approved in 2003 as A 926 - 03. 5 p. This test method covers a procedure for comparing materials used for coating, paving and lining corrugated metal pipe by use of a bed load abrasion testing machine. The procedure...
American Society for Testing and Materials (ASTM). Current edition approved September 1, 2005. Published September 2005. Originally approved in 1994. Last previous edition approved in 2004 as A 928/A 928M – 04. 6 p. This specification covers electric-fusion-welded steel pipe suitable for corrosive service. This specification covers grades of ferritic/austenitic steel as...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. Published July 2007. Originally approved in 1995. Last previous edition approved in 2001 as A 929/A 929M - 01. 4 p. This specification covers steel sheet used in the manufacture of corrugated steel pipe for storm sewers, culverts, drains, and similar uses. The sheet is metallic coated by the...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2009. Published December 2009. Originally approved in 1994. Last previous edition approved in 2003 as A930 - 03. 5 p. This practice covers a procedure for using life-cycle cost (LCC) analysis techniques to evaluate alternative drainage system designs using corrugated metal pipe that satisfies the...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published October 2007. Originally approved in 1975. Last previous edition approved in 2004 as A 938 – 04. 3 p. This test method describes the torsion (or twist) testing of metallic wire.
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. Published May 2007. Originally approved in 1995. Last previous edition approved in 2006 as A 939 – 96 (2006). 2 p. This practice covers a basic procedure of ultrasonically inspecting cylindrical forgings with bores from the bore surface.
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. Originally approved in 1995. Last previous edition approved in 2001 as A 940 – 96 (2001). 4 p. This specification covers vacuum treated, alloy steel forgings, differentially heat treated for turbine rotors. Differential heat treatment of a rotor forging involves...
American Society for Testing and Materials (ASTM). Current edition approved June 15, 2006. Published July 2006. 7p. This standard is a compilation of definitions of terms related to steel, stainless steel, related alloys, and ferroalloys.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published October 2005. Originally approved in 1995. Last previous edition approved in 2001 as A 943/A 943M – 01. 7 p. This specification covers spray-formed seamless austenitic stainless steel pipe intended for high-temperature and general corrosive service.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published October 2005. Originally approved in 1995. Last previous edition approved in 2001 as A 949/A 949M – 01. 4 p. This specification covers spray-formed seamless ferritic/austenitic stainless steel pipe intended for general corrosive service, with particular emphasis on resistance to...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2006. Published September 2006. Originally approved in 1996. Last previous edition approved in 2002 as A 956 – 02. 12 p. This test method covers the determination of the Leeb hardness of steel, cast steel, and cast iron (Part A), including the methods for the verification of Leeb hardness testing...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2007. Published February 2007. Originally approved in 1996. Last previous edition approved in 2006 as A 960/A 960M–06. 9 p. This specification covers a group of common requirements that shall apply to wrought steel piping fittings covered in any of the following individual product specifications or...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2007. Published February 2007. Originally approved in 1996. Last previous edition approved in 2005 as A 961/A 961M–05. 8 p. This specification covers a group of common requirements that shall apply to steel flanges, forged fittings, valves, and parts for piping applications under any of the...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2007. Published July 2007. Originally approved in 1997. Last previous edition approved in 2007 as A 962/A 962M – 07. 11 p. This specification covers a group of common requirements that shall apply to carbon, alloy and stainless steel fasteners or fastener materials, or both, under any of the...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2011. Published May 2011. Originally approved in 1996. Last previous edition approved in 2011 as A964/A964M - 03. 12 p. This specification covers material, geometric, and wall section properties of steel box culverts manufactured from corrugated plate or sheet, with or without attached stiffeners,...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2006. Published September 2006. Originally approved in 1996. Last previous edition approved in 2006 as A 965/A 965M – 06. 7 p. This specification covers austenitic stainless steel forgings for boilers, pressure vessels, high temperature parts, and associated equipment.
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. Published June 2007. Originally approved in 1996. Last previous edition approved in 2006 as A 966/A 966M – 96 (2006). 6 p. This practice covers a procedure for the magnetic particle examination of steel forgings using alternating current as the power source. The procedure will produce...
American Society for Testing and Materials (ASTM). Current edition approved April 2002. 7 p.
This specification covers several different types of chemical passivation treatments for stainless steel parts. It includes recommendations and precautions for descalinz '" cleaning, and passivation of stainless steel parts. It includes several alternative tests, with acceptance criteria,...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1996. Last previous edition approved in 2001 as A 967 – 01. 7 p. This specification covers several different types of chemical passivation treatments for stainless steel parts. It includes recommendations and precautions for descaling,...
Настоящие технические условия (далее по тексту – ТУ) распространяются на несколько различных типов химической пассивации и обработки нержавеющих стальных деталей. Эти ТУ дают рекомендации и меры предосторожности при удалении окалины, очистке и пассивации деталей из нержавеющей стали. ТУ дают описание нескольких альтернативных тестов с критериями входного контроля, для...
Publisher: ASTM.
Publish Date: 2015.
Pages: 9.
Language: English.
Format: PDF.
Document Scope .
1.1 This specification covers deformed steel reinforcing.
bars in cut lengths, with a head attached to one or both ends, for.
concrete reinforcement. Heads are forge-formed, machined.
from bar stock, or cut from plate. Attachment can be accomplished.
through:
1.1.1 Welding;...
American Society for Testing and Materials (ASTM). Current edition approved May 10, 2003. Published June 2003. 7p. This specification covers gabions and gabion mattresses produced from metallic-coated welded wire fabric, and metallic-coated wire for spiral binders, lacing wire, and stiffeners used to assemble the product. The metallic-coated fabric may be polyvinyl chloride (PVC)...
American Society for Testing and Materials (ASTM). Current edition approved May 10, 2003. Published June 2003. 7 р. This specification covers gabions and revet mattresses produced from double-twisted metallic-coated wire mesh, and metallic-coated wire for lacing wire, stiffeners, and fasteners used for manufacturing, assembling, and installation of the product. This specification...
American Society for Testing and Materials (ASTM). Current edition approved Nov 1, 2009. Published November 2010. 4p. This specification covers the minimum material requirements and describes the procedures for installing concrete pavements and linings in corrugated steel pipes and structural plate structures in the field. Specific designs with additional or greater requirements...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally published in 1998. Last previous edition approved in 2002 as A 982 – 02. 4 p. This specification covers stainless steel forgings for compressor and turbine bucket, blade, and airfoil applications.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2006. Published September 2006. Originally approved in 1998. Last previous edition approved in 2005 as A 983/A 983M – 05. 5 p. This specification covers continuous grain flow forged carbon and alloy steel crankshafts for medium speed diesel and natural gas engines.
American Society for Testing and Materials (ASTM). Current edition approved April 10, 2003. Published May 2003. 14p. This specification covers a group of common requirements, which are mandatory for steel castings produced by the investment casting process for pressure-containing ASTM Specifications.
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published April 2006. Originally approved in 1998. Last previous edition approved in 2001 as A 986/A 986M – 01. 3 p. This specification covers the magnetic particle examination of forged continuous grain flow (CGF) crankshafts intended for medium speed diesel engines.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published October 2007. Originally approved in 1998. Last previous edition approved in 2005 as A 989/A 989M – 05. 8 p. This specification covers hot isostatically-pressed, powder metallurgy, alloy steel piping components for use in pressure systems. Included are flanges, fittings, valves,...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published October 2007. Originally approved in 1998. Last previous edition approved in 2005 as A 989/A 989M – 05. 8 p. This specification covers hot isostatically-pressed, powder metallurgy, alloy steel piping components for use in pressure systems. Included are flanges, fittings, valves,...
American Society for Testing and Materials (ASTM). Current edition approved June 15, 2005. Published June 2005. Originally approved in 1998. Last previous edition approved in 2003 as A 994 – 03. 9 p. This guide covers the editorial form and style for product specifications under the jurisdiction of ASTM Committee A01. This guide has been prepared as a supplement to the current...
ASTM, 2013, 4p. A 995/ 995M Standard Specification for Castings, Austenitic-Ferritic (Duplex) Stainless Steel, for Pressure-Containing Parts Brief Summary This specification covers austenitic-ferritic (duplex) stainless steel castings for valves, flanges, fittings, and other pressure-containing parts. The grades of steels covered here are: Grade 1B, Grade 2A, Grade 3A, Grade...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2006. Published May 2006. Originally approved in 1998. Last previous edition approved in 2006 as A 996/A 996M – 06. 5 p. This specification covers rail-steel and axle-steel bars for concrete reinforcement. Three types of product are included, designated with a rail symbol, and an R for bars made of...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2008. Published June 2008. Originally approved in 1998. Last previous edition approved in 1998 as A 998/A 998M - 98(2003). 19 p. This practice covers the structural design of reinforcement for fittings in factory-made, round corrugated steel pipe, conforming to Specifications A 760/A 760M or A 762/...
American Society for Testing and Materials (ASTM), 2004. — 11 p. This standard is issued under the fixed designation A 999/A 999M; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (e) indicates an...
ASTM International, 18 с.
Утверждено: 1 март 2014 г.
Данная спецификация содержит общие требования, применяемые, если другое не оговорено в отдельных спецификациях, для труб из легированной и нержавеющей стали.
American Society for Testing and Materials (ASTM). 2004. 10p. This specification covers a group of general requirements that, unless otherwise specified in an individual specification, shall apply to the ASTM product specifications
2000. American Society for Tesing and Materials — 13 p. This Speccification covers alloy and stainless steel bolting material for pressure vessels, valves, flanges, and fittings for high-temperature service.
ASTM. — 54 с. Использование настоящего утверждено агентствами Министерства обороны. Данные методы испытаний охватывают процедуры и определения для механического испытания ковкой и литой стали, нержавеющих сталей и сплавов. Различные механические испытания, описанные здесь, используются для определения свойств, продиктованные в спецификациях на продукцию (изделия). Отклонения в...
ASTM A370-17 Standard Test Methods and Definitions for Mechanical Testing of Steel Products This standard is issued under the fixed designation A370; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (´)...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2007. Published March 2007. Originally approved in 1939. Last previous edition approved in 2003 as B 117–03. 10 p. This practice covers the apparatus, procedure, and conditions required to create and maintain the salt spray (fog) test environment. Suitable apparatus which may be used is...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2011. Published November 2011. Originally approved in 1939. Last previous edition approved in 2009 as B117–09. 12 p. This practice covers the apparatus, procedure, and conditions required to create and maintain the salt spray (fog) test environment. Suitable apparatus which may be used is...
Настоящий стандарт распространяется на камеры, процедуры и условия, требуемые для создания и поддержания условий испытаний соляным раствором (туманом).
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2006. Published February 2006. Originally approved in 1939. Last previous edition approved in 2001 as B 121/B 121M – 01. 4 p. This specification establishes the requirements for copper-zinc-lead alloys (leaded brass) plate, sheet, strip, and rolled bar. The following alloys are covered Copper Alloy...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2006. Published February 2006. Originally approved in 1939. Last previous edition approved in 2001 as B 122/B 122M – 01. 7 p. This specification establishes the requirements for copper-nickel-tin alloy, copper-nickel-zinc alloy (nickel silver), and copper-nickel alloy plate, sheet, strip, and...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2006. Published February 2006. Originally approved in 1939. Last previous edition approved in 2004 as B 124/B 124M – 04. 5 p. This specification establishes the requirements for copper and copper alloy rod, bar, and shapes intended for hot forging
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published June 2005. Originally approved in 1939. Last previous edition approved in 1998 as B 127 - 98. 6 p. This specification covers rolled nickel-copper alloy (UNS N04400) plate, sheet, and strip. The values stated in inch-pound units are to be regarded as the standard. The other values...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published November 2005. Originally approved in 1940. Last previous edition approved in 2001 as B 134/B 134M – 01. 7 p. This specification establishes requirements for round, hexagonal, octagonal, rectangular and square brass wire of UNS Alloy Nos. C21000, C22000, C22600, C23000, C23400,...
American Society for Testing and Materials (ASTM). Current edition approved March 15, 2006. Published April 2006. Originally approved in 1984. Last previous edition approved in 2000 as B 135M – 00. 6 p. This specification covers seamless round and rectangular including square copper alloy tube in straight lengths of UNS Alloy Nos. C22000, C23000, C26000, C27000, C27200, C27400,...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2006. Published February 2006. Originally approved in 1941. Last previous edition approved in 2001 as B 138/B 138M – 01. 4 p. This specification establishes the requirements for manganese bronze rod, bar and shapes produced in Copper Alloy UNS Nos. C67000, C67500, or C67600.
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2006. Published February 2006. Originally approved in 1941. Last previous edition approved in 2001 as B 139/B 139M – 01. 5 p. This specification establishes the requirements for phosphor bronze rod, bar, and shapes.
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published November 2005. Originally approved in 1941. Last previous edition approved in 2000 as B 151 – 00. 5 p. This specification establishes the requirements for copper-nickel-zinc and copper-nickel rod and bar for general application produced from Copper Alloy UNS Nos. C70600, C70620,...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1942. Last previous edition approved in 2006 as B 152/B 152M – 06. 7 p. This specification2 establishes the requirements for copper sheet, strip, plate, and rolled bar produced from the following coppers.
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published October 2005. Originally approved in 1941. Last previous edition approved in 2003 as B 153 – 91 (2003). 2 p. This test method establishes the requirements for the expansion pin test for copper and copper-alloy pipe and tubing with an inside diameter of 0.125 in. (3.2 mm) and greater...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published October 2005. Originally approved in 1941. Last previous edition approved in 2001 as B 154 – 01. 3 p. This test method describes the technique for conducting the mercurous nitrate test for residual stresses in wrought copper alloy mill products.
American Society for Testing and Materials (ASTM). Current edition approved Mar. 1, 2005. Published March 2005. Originally approved in 1941. Last previous edition approved in 2001 as B 159 – 01. 3 p. This specification establishes the requirements for round, square and flat phosphor bronze wire of UNS Alloy Nos. C51000, C52100, and C52400 for general and spring applications.
American Society for Testing and Materials (ASTM). Current edition approved March 10, 2005. Published March 2005. Originally approved in 1917. Last previous edition approved in 2000 as B16–00. 8 p. This specification establishes the requirements for free-cutting brass rod, bar, wire, and shapes of any specified cross section produced from Copper Alloy UNS No. C36000 suitable for...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published June 2005. Originally approved in 1941. Last previous edition approved in 1999 as B 160 – 99. 6 p. This specification covers nickel (UNS N02200)*, low carbon nickel (UNS N02201)*, and solution strengthened nickel (UNS N02211) in the form of hot-worked and cold-worked rod and bar in...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published December 2005. Originally approved in 1941. Last previous edition approved in 2003 as B 161 - 03. 4 p. This specification covers nickel (UNS N02200)* and low-carbon nickel (UNS N02201)* in the form of cold-worked seamless pipe and tube in the conditions shown in Table 1 and Table...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published February 2006. Originally approved in 1941. Last previous edition approved in 1999 as B 162 – 99. 9 p. This specification covers rolled nickel (UNS N02200) and low-carbon nickel (UNS N02201) plate, sheet, and strip.
American Society for Testing and Materials (ASTM). Current edition approved March 15, 2008. Published March 2008. Originally approved in 1941. Last previous edition approved in 2004 as B 163 – 04. 12 p. This specification covers seamless tubes of nickel and nickel alloys, as shown in Table 1, for use in condenser and heat-exchanger service. This specification covers outside...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published December 2005. Originally approved in 1941. Last previous edition approved in 2003 as B 165 – 93 (2003). 6 p. This specification covers nickel-copper alloy UNS N04400* in the form of cold-worked seamless pipe and tube in the conditions shown in Table 1 and Table X1.1.
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1941. Last previous edition approved in 2004 as B 166 – 04. 8 p. This specification2 covers nickel-chromium-iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, and N06045)* and nickel-chromium-cobalt-molybdenum alloy (UNS N06617) in...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1941. Last previous edition approved in 2005 as B 167 – 05a. 8 p. This specification covers nickel-chromium-iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, and N06045)* and nickel-chromium-cobalt-molybdenum alloy (UNS N06617) in...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1941. Last previous edition approved in 2005 as B 168 – 01 (2005). 11 p. This specification covers rolled nickel-chromium-iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, and N06045)* and nickel-chromium-cobalt-molybdenum alloy...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published November 2005. Originally approved in 1941. Last previous edition approved in 2001 as B 169/B 169M – 01. 4 p. This specification establishes the requirements for Copper Alloy UNS Nos. C61300 and C61400 aluminum bronze sheet, strip, and rolled bar.
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1944. Last previous edition approved in 2003 as B 187 – 03. 9 p. This specification establishes the requirements for copper conductor bar, rod, and shapes for electrical (bus) applications and rod, bar, and shapes for general applications.
American Society for Testing and Materials (ASTM). Current edition approved Mar. 1, 2005. Published March 2005. Originally approved in 1919. Last previous edition approved in 2001 as B 19 – 01. 6 p. This specification establishes the requirements for sheet, strip, plate, bar, and disks for the manufacture of ammunition of component parts thereof from alloy UNS C26000.
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2006. Published February 2006. Originally approved in 1946. Last previous edition approved in 2004 as B 208 – 04. 11 p. This practice establishes procedures for preparing test coupons and specimens (machined and unmachined) for tension tests of copper alloys for sand, permanent mold, centrifugal...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published August 2007. 34 р. This standard has been approved as a Gulf Standard without any technical modifications by GSO Technical Council in its meeting 30-31.10.2010. This specification covers aluminum and aluminum alloy flat sheet, coiled sheet, and plate in the alloys and tempers...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2006. Published February 2006. Originally approved in 1918. Last previous edition approved in 2001 as B 21/B 21M – 01. 7 p. This specification establishes the requirements for naval brass rod, bar, and shapes produced from Copper Alloy UNS Nos. C46200, C46400, C47940, C48200, or C48500.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2003. Published November 2003. 11 р. This specification covers rolled or cold-finished bar, rod, and wire in alloys and tempers as shown in Table 2. NOTE 1—Throughout this specification use of the term alloy in the general sense includes aluminum as well as aluminum alloy. NOTE 2—The term cold...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published November 2005. Originally approved in 1926. Last previous edition approved in 2000 as B 23 – 00. 4 p. This specification covers eight typical white metal bearing alloys, in bar or ingot form, known commercially as babbitt metal. The alloys are specified, covering the range...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published December 2006. Originally approved in 1995. Last previous edition approved in 2001 as B 237 – 01. 2 p. This specification covers refined antimony in ingot, pig, or cake form. The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2009. Published November 2009. 4 р. This specification covers commercial zinc and zincaluminum (ZA) alloys in ingot form for remelting for the manufacture of pressure die castings, foundry castings and continuous cast bar stock as designated and specified in Table 1.
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1951. Last previous edition approved in 2001 as B 248 – 01. 12 p. This specification establishes the general requirements common to several wrought product specifications. Unless otherwise specified in the purchase order or in an individual...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1980. Last previous edition approved in 2001 as B 248M – 01. 12 p. This specification establishes the general requirements common to several wrought product specifications. Unless otherwise specified in the purchase order or in an individual...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2006. Published February 2006. Originally approved in 1951. Last previous edition approved in 2004 as B 249/B 249M – 04. 13 p. This specification establishes the general requirements common to wrought copper and copper alloy rod, bar, shapes, and forgings which shall apply to Specifications B 16/B...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published December 2006. Originally approved in 1952. Last previous edition approved in 2006 as B 265 – 06a. 10 p. This specification covers annealed titanium and titanium alloy strip, sheet, and plate.
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1954. Last previous edition approved in 2003 as B 271 – 96 (2003). 6 p. This specification establishes requirements for centrifugal castings of copper-base alloys having the nominal compositions shown in Table 1
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1952. Last previous edition approved in 2001 as B 277 – 95 (2001). 2 p. This test method covers the determination of the hardness of metallic materials used for electrical contacts. Rockwell, Rockwell superficial, Brinell, and microhardness tests...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2006. Published February 2006. Originally approved in 1953. Last previous edition approved in 2004 as B 283 – 04. 8 p. This specification establishes the requirements for copper and copper alloy die forgings produced by the hot pressing method.
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1919. Last previous edition approved in 2006 as B 30 – 06. 13 p. This specification establishes the requirements for copper alloys in ingot form for remelting for the manufacturing of castings having the Copper Alloy UNS No. designation,...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2006. Published February 2006. Originally approved in 1957. Last previous edition approved in 1999 as B 315 – 99. 10 p. This specification establishes the requirements for seamless, copper alloy pipe and tube in nominal pipe sizes, both regular and extra strong, and seamless tube in straight...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published February 2006. Originally approved in 1958. Last previous edition approved in 2001 as B 327 – 01. 4 p. This specification covers aluminum–base and zinc–base master alloys used to make zinc die-casting alloys. Alloy compositions specified for aluminum–base master alloys (hardeners)...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1958. Last previous edition approved in 2006 as B 338 – 06. 8 p. This specification covers the requirements for 28 grades of titanium and titanium alloy tubing intended for surface condensers, evaporators, and heat exchangers.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published February 2006. Originally approved in 1967. Last previous edition approved in 2000 as B 339 - 00. 4 p. This specification covers refined tin in pig form recovered and cast from primary and secondary tin-bearing materials. One grade of tin metal is specified and is designated by the...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1959. Last previous edition approved in 2006 as B 348 – 06. 8 p. This specification covers annealed titanium and titanium alloy bars and billets.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2006. Published September 2006. Originally approved in 1960. Last previous edition approved in 2002 as B 350/B 350M – 02. 4 p. This specification covers vacuum-melted zirconium and zirconium alloy ingots for nuclear application.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 15, 2006. Published October 2006. Originally approved in 1960. Last previous edition approved in 2002 as B 352/B 352M – 02. 6 p. This specification covers hot- and cold-rolled zirconium and zirconium alloy sheet, strip, and plate. One unalloyed and three alloys for use in nuclear applications are...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1960. Last previous edition approved in 2002 as B 359/B 359M – 02. 11 p. This specification2 establishes the requirements for seamless copper and copper alloy tubing on which the external or internal surface, or both, has been modified by a...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2006. Published February 2006. Originally approved in 1920. Last previous edition approved in 2001 as B 36/B 36M – 01. 8 p. This specification establishes the requirements for brass plate, sheet, strip, and rolled bar of the following alloys Copper Alloy UNS No.: C21000, C22000, C22600, C23000,...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1961. Last previous edition approved in 2006 as B 363 – 06. 4 p. This specification covers fittings intended for general corrosion-resisting and elevated-temperature services, factory made from unalloyed titanium and titanium alloys. The term...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. Originally approved in 1961. Last previous edition approved in 2005 as B 367 – 05. 5 p. This specification covers titanium and titanium alloy castings intended for general corrosion resistant and industrial applications.
American Society for Testing and Materials (ASTM). Current edition approved April 15, 2009. Published May 2009. 5 р. This test method prescribes the conditions required in copper-accelerated acetic acid-salt spray (CASS) testing for specification purposes. The standard does not specify the type of test specimen or exposure periods to be used for a specific product, nor the...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1961. Last previous edition approved in 2003 as B 369 – 96 (2003). 5 p. This specification establishes the requirements for copper-nickel alloy castings with nominal compositions shown in Table 1.
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1961. Last previous edition approved in 2005 as B 371/B 371M – 05. 3 p. This specification establishes the requirements for copper-zinc-silicon alloy rod produced in Copper Alloy UNS Nos. C69300, C69400, C69430, C69700, and C69710.
American Society for Testing and Materials (ASTM). Current edition approved June 2008. Published 2006. Originally approved in 1961. 11 p. This Specification covers 39 grades of annealed titanium and titanium alloy forgings. The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published July 2006. Originally approved in 1962. Last previous edition approved in 2000 as B 388 – 00. 7 p. This specification covers thermostat metals in the form of sheet or strip that are used for the temperature-sensitive elements of devices for controlling, compensating, or indicating...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published June 2005. Originally approved in 1999. Last previous edition approved in 2003 as B 393 - 03. 5 p. This specification covers five grades of wrought niobium and niobium alloy strip, sheet, and plate. Except for dimensional tolerances in Table 1, the values stated in inch-pound...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1957. Last previous edition approved in 2001 as B 408 – 01. 5 p. This specification covers UNS N08120, UNS N08800, UNS N08810, UNS N08811*, and UNS N08890 in the form of hot-worked and cold-worked rod and bar. Alloy UNS N08800 is normally...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1957. Last previous edition approved in 2001 as B 409 – 01. 5 p. This specification covers UNS N08120, UNS N08890, UNS N08800, UNS N08810, and UNS N08811* in the form of rolled plate, sheet, and strip. Alloy UNS N08800 is normally employed in...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1965. Last previous edition approved in 2001 as B 411/ 411M – 01. 3 p. This specification establishes the requirements for copper-nickel-silicon alloy rod and bar produced from Copper Alloy UNS No. C64700 in straight lengths
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1964. Last previous edition approved in 2001 as B 418 – 01. 3 p. This specification covers cast and wrought galvanic zinc anodes used for the cathodic protection of more noble metals and alloys in sea water, brackish water, other saline...
Publisher: ASTM
Publish Date: 2015
Pages: 7
Language: English
Book of Standards Volume: 02.01
Abstract
This specification covers seamless copper pipe in all nominal standard pipe sizes, both regular and extra-strong, suitable for use in plumbing, boiler feed lines, and for similar purposes. The material shall conform to the specified chemical requirements. The pipe shall...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 15, 2006. Published October 2006. Originally approved 1965. Last previous edition approved in 2005 as B 422 – 05. 5 p. This specification establishes the requirements for Copper Alloy UNS Nos. C19010, C19020, C19025, C63800, C64725, C70250, C70260, and C70265 sheet and strip.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published December 2005. Originally approved in 1964. Last previous edition approved in 2003 as B 423 - 03. 4 p. This specification covers nickel-iron-chromium-molybdenum-copper alloys (UNS N08825 and N08221) in the form of cold-worked and hot-finished seamless pipe and tube intended for...
Identical with ASTM Specification B 423-99 except that certification has been made mandatory.
This specification covers nickel-iron-chromium-molybdenum-copper alloys (UNS N08825 and UNS N08221) in the form of cold-worked and hot-finished seamless pipe and tube intended for general corrosive service. The general requirements for pipe and tube are covered in Specification B
829.
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published June 2005. Originally approved in 1964. Last previous edition approved in 1998 as B 424 – 98a. 4 p. This specification2 covers rolled nickel-iron-chromium-molybdenum-copper alloy (UNS N08825 and UNS N08221) plate, sheet, and strip.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published February 2006. Originally approved in 1964. Last previous edition approved in 1999 as B 425 – 99. 5 p. This specification2 covers nickel-iron-chromium-molybdenum-copper alloy (UNS N08825 and UNS N08221) in the form of hot-finished and cold-drawn rounds, squares, hexagons, and...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1966. Last previous edition approved in 2000 as B 434 – 00. 3 p. This specification2 covers nickel-molybdenum-chromium-iron alloys (UNS N10003 and UNS N10242) plate, sheet, and strip for use in general corrosive service.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1966. Last previous edition approved in 2003 as B 435 - 03. 3 p. This specification covers alloys UNS N06002, UNS N06230, UNS N12160, and UNS R30556 in the form of rolled plate, sheet, and strip for heat-resisting and general corrosive service.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published February 2006. Originally approved in 1966. Last previous edition approved in 2000 as B 440 – 00. 3 p. This specification covers refined cadmium metal in slab, ball or stick form. The values stated in inch-pound units are to be regarded as the standard.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published February 2006. Originally approved in 1966. Last previous edition approved in 2000 as B 443 - 00. 8 p. This specification covers rolled nickel-chromium-molybdenum-columbium alloy (UNS N06625) and nickel-chromium-molybdenum-silicon alloy (UNS N06219)* plate, sheet, and strip
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1966. Last previous edition approved in 2004 as B 444 - 04. 4 p. This specification covers nickel-chromium-molybdenum-columbium alloys (UNS N06625 and UNS N06852) and nickel-chromium-molybdenum-silicon alloy (UNS N06219) in the form of...
Standard Specification for Chromates on Aluminum.
Scope
Referenced Documents
Terminology
Classification
Surfaces Preparation
Methods of Application of Chromate Coatings
Coating Requirements
Keywords
APPENDIXES
X
1. QUALITATIVE TESTING OF THE LAYER COMPOSITION
X1.1 Reagents
X1.2 Determination of Chromium in the Layer
X1.3 Testing for Phosphate
X1.4 Testing for Zinc...
Настоящие технические условия распространяются
на требования к хроматным конверсионным покрытиям
на алюминии и алюминиевых сплавах, нанесенные
способом с промыванием и без него, предназначенных
для обеспечения защиты от коррозии и в качестве базы
для других покрытий. Это издание технических условий
было согласовано с ISO/DIS 10546 и является технически
эквивалентным.
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published November 2005. Originally approved in 1967. Last previous edition approved in 2001 as B 453/B 453M – 01. 5 p. This specification establishes the requirements for copper-zinc-lead alloy (leaded-brass) rod, bar, wire, and shapes produced from Copper Alloys UNS Nos. C33500, C34000,...
American Society for Testing and Materials (ASTM). Current edition approved Mar. 1, 2005. Published March 2005. Originally approved in 1967. Last previous edition approved in 2001 as B 455 – 01. 3 p. This specification establishes the requirements for extruded leaded-brass angles, channels, and other architectural shapes of solid cross section produced in Copper Alloy UNS Nos....
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1967. Last previous edition approved in 2004 as B 462 – 04. 5 p. This specification covers forged or rolled pipe flanges, forged fittings, and valves and parts intended for corrosive high-temperature service.The values stated in inch-pound units are...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published November 2005. Originally approved in 1967. Last previous edition approved in 2004 as B 464 – 04. 3 p. This specification covers welded UNS N08020, N08024, and N08026 alloy pipe for general corrosion-resisting and low- or high-temperature service.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1968. Last previous edition approved in 2001 as B 476 – 01. 4 p. This specification covers general requirements common to wrought precious metal electrical contact alloy products in the form of sheet, strip, wire, and rod. Unless otherwise specified...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published June 2005. Originally approved in 1969. Last previous edition approved in 2001 as B 495 – 01. 3 p. This specification covers six grades of zirconium ingots. The values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1969. Last previous edition approved in 2000 as B 497 – 00. 3 p. This guide describes recommended procedures to accurately measure voltage drop across current carrying contacts and the parameters to be documented in order to effectively record the...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published October 2005. Originally approved in 1911. Last previous edition approved in 2000 as B 5 – 00. 4 p. This specification establishes the requirements for high conductivity, tough-pitch, copper wire bars, cakes, slabs, billets, ingots, and ingot bars.
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2012. Published May 2012. 9 p. This specification establishes requirements for continuously cast rod, bar, tube, and shapes produced from copper alloys with nominal compositions as listed in Table 1.2 Castings produced to this specification may be manufactured for and supplied from stock. In...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published February 2006. Originally approved in 1970. Last previous edition approved in 2001 as B 511 – 01. 5 p. This specification covers wrought alloys UNS N08330 and UNS N08332 in the form of hot-finished and cold-finished bar and shapes intended for heat-resisting applications and general...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published November 2005. Originally approved in 1970. Last previous edition approved in 2002 as B 514 – 95 (2002). 3 p. This specification covers nickel-iron-chromium alloys in the form of welded, cold-worked, and annealed pipe for general corrosive service and heat-resisting applications....
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published November 2005. Originally approved in 1970. Last previous edition approved in 2003 as B 517 – 03. 3 p. This specification covers welded, cold-worked, and annealed nickel-chromium-iron alloy (UNS N06600, N06603, N06025, and N06045) pipe for general corrosive service and...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1970. Last previous edition approved in 2001 as B 522 – 01. 2 p. This specification covers 69 % gold, 25 % silver, 6 % platinum alloy tubing, rod, wire, and sheet material for sliding electrical contacts.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2006. Published September 2006. Originally approved in 1970. Last previous edition approved in 2002 as B 523/B 523M – 02. 5 p. This specification covers three grades of zirconium and zirconium alloy seamless and welded tubes. Unless a single unit is used, for example corrosion mass gain in...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1970. Last previous edition approved in 2004 as B 535 – 04. 3 p. This specification covers alloys UNS N08330 and N08332 in the form of hot-finished and cold-finished seamless pipe and tube intended for heat resisting applications and general...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1970. Last previous edition approved in 2001 as B 541 – 01. 3 p. This specification covers a gold-rich, age-hardenable alloy in rod, wire, and strip form applicable to electrical contacts. The values stated in inch-pound units are to be regarded...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2006. Published May 2006. 15 p. These test methods cover the tension testing of wrought and cast aluminum- and magnesium-alloy products, excepting aluminum foil2, and are derived from Test Methods E8, which cover the tension testing of all metallic materials. This standard does not purport to...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published February 2006. Originally approved in 1972. Last previous edition approved in 2000 as B 560 - 00. 3 p. This specification covers three alloy types, made from tin, antimony, and copper, used in the fabrication of pewter articles by casting, spinning, drawing, or forming. The metal...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published June 2005. Originally approved in 1972. Last previous edition approved in 1999 as B 561 – 94 (1999). 2 p. This specification covers refined platinum as sponge, cast bar, and wrought forms (Note 1) in two grades as follows: Grade 99.95 (UNS PO4995)— Platinum having a purity of...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published June 2005. Originally approved in 1972. Last previous edition approved in 1999 as B 562 – 95 (1999). 4 p. This specification covers refined gold in cast bar form (Note 1): Grade 99.5—Gold having a minimum fineness of 995. Grade 99.95— Gold having a minimum fineness of 999.5. Grade...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1972. Last previous edition approved in 2001 as B 563 – 01. 3 p. This specification covers an alloy containing palladium, silver, copper, platinum, and nickel in the form of wire, rod, and strip for electrical contacts.
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1972. Last previous edition approved in 2006 as B 564 – 06. 11 p. This specification2 covers forgings of nickel alloy UNS N02200, Ni-Cu alloy UNS N04400, Ni-Cr-Fe alloys UNS N06600, UNS N06603, and UNS N06690, Ni-Cr-Mo-Nb alloy UNS N06625,...
This specification covers forgings of nickel alloy UNS N02200, Ni-Cu alloy UNS N04400, Ni-Cr-Fe alloys UNS N06600, UNS N06603, and UNS N06690, Ni-Cr-Mo-Nb alloy UNS N06625, Ni-Cr-Mo-Si alloy UNS N06219, low-carbon Ni-Mo-Cr alloys UNS N10276 and UNS N06022, Ni-Cr-Mo-W alloy UNS N06110, low-carbon Ni-Cr-Mo-W alloy UNS N06686, Ni-Fe-Cr-Mo-Cu alloy UNS N08825, Fe-Ni-Cr-Mo-N alloy UNS...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1972. Last previous edition approved in 2005 as B 570 – 05a. 4 p. This specification establishes the requirements for copper-beryllium alloy forgings and extrusions produced from the following alloys.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1972. Last previous edition approved in 2003 as B 572 - 03. 4 p. This specification covers alloys UNS N06002, UNS N06230, UNS N12160, and UNS R30556 in the form of rod for heat resisting and general-corrosive service.
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1972. Last previous edition approved in 2000 as B 573 – 00. 3 p. This specification covers nickel-molybdenum-chromium- iron alloys (UNS N10003 and UNS N10242) rod for use in general corrosive service.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1972. Last previous edition approved in 2005 as B 574 – 05. 4 p. This specification covers rod of low-carbon nickel-chromium-molybdenum alloys (UNS N10276, N06022, N06035, N06455, N06058, and N06059), low-carbon nickel-molybdenum-chromium-tantalum...
ASTM 2004, 4p. ASTM B 575 Standard Specification for Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon NickelChromium-Molybdenum-Copper, Low-Carbon NickelChromium-Molybdenum-Tantalum, and Low-Carbon NickelChromium-Molybdenum-Tungsten Alloy Plate, Sheet, and Strip. Scope This specification2 covers plate, sheet, and strip of low-carbon...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1972. Last previous edition approved in 2004 as B 575 - 04. 4 p. This specification2 covers plate, sheet, and strip of low-carbon nickel-chromium-molybdenum alloys (UNS N10276, N06022, N06455, N06035, UNS N06058, UNS N06059)*, low-carbon...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published November 2005. Originally approved in 1973. Last previous edition approved in 1999 as B 576 – 94 (1999). 2 p. This guide covers the major variables which affect the rate of arc erosion of electrical contact materials and serves as a guide in developing more detailed specifications...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2009. Published December 2009. Originally approved in 1973. Last previous edition approved in 2009 as B584 – 09. 7 p. This specification covers requirements for copper alloy sand castings for general applications. Nominal compositions of the alloys defined by this specification are shown in Table...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1973. Last previous edition approved in 2003 as B 587 – 97 (2003). 10 p. This specification establishes the requirements for round, rectangular, and square copper alloy welded tube for general engineering applications.
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published June 2005. Originally approved in 1973. Last previous edition approved in 1999 as B 589 – 94 (1999). 2 p. This specification covers refined palladium as sponge, cast bar, and wrought forms (Note 1) in one grade as follows: Grade 99.95 (UNS PO3995)— Palladium having a purity of...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2006. Published February 2006. Originally approved in 1973. Last previous edition approved in 2001 as B 592 – 01. 4 p. This specification covers the requirements for plate, sheet, strip, and rolled bar in alloys C66300 and C68800.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1974. Last previous edition approved in 1999 as B 596 – 89 (1999). 3 p. This specification covers a wrought alloy containing gold and copper in the form of wire, rod, strip, and tubing for electrical contacts.
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1911. Last previous edition approved in 2003 as B 6 – 03. 4 p. This specification covers zinc metal made from ore or other material by a process of distillation or by electrolysis in five grades as follows: 1 LME Grade 2 Special High Grade 3...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1976. Last previous edition approved in 2000 as B 613 – 76 (2000). 2 p. This guide defines the criteria for composition, properties, and other requirements for brushes containing a matrix of one or more conducting metallic elements or alloys and one...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published June 2005. Originally approved in 1977. Last previous edition approved in 2000 as B 614 – 95 (2000). 3 p. This practice covers a cleaning and descaling procedure useful to producers, users, and fabricators of zirconium and zirconium alloys for the removal of ordinary shop soils,...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1979. Last previous edition approved in 2000 as B 615 – 79 (2000). 3 p. This practice describes the practices and factors considered to be most important in the measurement of electrical contact noise of sliding contacts.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1977. Last previous edition approved in 2000 as B 616 – 96 (2000). 2 p. This specification covers refined rhodium as sponge and powder in three grades as follows: 1 Grade 99.80—Rhodium having a purity of 99.80 %, 2 Grade 99.90—Rhodium having a...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1981. Last previous edition approved in 2005 as B 619 – 05. 6 p. This specification covers welded pipe of nickel and nickel-cobalt alloys (UNS N10001; UNS N10242; UNS N10665; UNS N12160; UNS N10624; UNS N10629; UNS N10675; UNS N10276; UNS N06455;...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published December 2006. Originally approved in 1977. Last previous edition approved in 2002 as B 621 – 02. 3 p. This specification covers nickel-iron chromium-molybdenum alloy (UNS N08320)* rod for use in general corrosive service. The following products are covered under this...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1977. Last previous edition approved in 2004 as B 622 – 04a. 6 p. This specification covers seamless pipe and tube of nickel and nickel-cobalt alloys (UNS N10001, UNS N10242, UNS N10665, UNS N12160, UNS N10675, UNS N10276, UNS N06455, UNS N06007,...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2005. Published July 2005. Originally approved in 1977. Last previous edition approved in 2004 as B 625 – 04a. 2 p. This specification covers alloys UNS N08925, UNS N08031, UNS N08932, UNS N08926, UNS N08354, and UNS R20033 plate, sheet, and strip in the annealed temper. ASTM International has...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1977. Last previous edition approved in 2004 as B 626 - 04. 5 p. This specification covers welded tubes made from the nickel and nickel-cobalt alloys (UNS N10001, UNS N10242, UNS N10665, UNS N12160, UNS N10629, UNS N10624, UNS N10675, UNS N10276,...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1970. Last previous edition addition approved in 2003 as B 637 – 03. 6 p. This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for high-temperature service (Table 1).
This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for high-temperature service (Table 1).
The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
American Society for Testing and Materials (ASTM). Current edition approved March 15, 2006. Published April 2006. Originally approved in 1978. Last previous edition approved in B 640 – 00. 9 p. This specification establishes the requirements for welded copper tube for air conditioning and refrigeration service for use in connections, repairs, and alterations. The tube shall be...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published October 2005. Originally approved in 1978. Last previous edition approved in 2000 as B 643 – 00. 5 p. This specification establishes requirements for copper-beryllium alloy seamless tube in straight lengths. Copper Alloy UNS C17200 will be the alloy furnished whenever Specification...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published November 2005. Originally approved in 1982. Last previous edition approved in 2003 as B 644 – 95 (2003). 5 p. This specification establishes the requirements for copper nickel, ferro copper, phosphor copper, and silicon copper master alloys in ingot, shot, and waffle form to be used...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1981. Last previous edition approved in 2005 as B 649 - 05. 7 p. This specification covers nickel-iron-chromium-molybdenum-copper-nitrogen alloys (UNS N08925, UNS N08031, UNS N08354, and UNS N08926), and chromium-nickel-iron-nitrogen low-carbon...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2006. Published September 2006. Originally approved in 1979. Last previous edition approved in 2002 as B 653/B 653M – 02. 3 p. This specification covers fittings, factory made from three grades of zirconium and zirconium alloys. The term welding fittings applies to butt-welding parts such as 45...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2006. Published September 2006. Originally approved in 1979. Last previous edition approved in 2005 as B 658/B 658M – 05. 5 p. This specification covers three grades of seamless and welded zirconium pipe. Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1936. Last previous edition approved in 2003 as B 66 – 95 (2003). 3 p. This specification establishes requirements for bronze castings for steam locomotive wearing parts. The following Copper Alloy UNS Nos. are specified: C93200, C93400, C93600,...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1979. Last previous edition approved in 2000 as B 662 – 94 (2000). 3 p. This specification covers electrical contact components made from silver-molybdenum by powder metallurgical procedures. This specification covers compositions within the...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1979. Last previous edition approved in 2000 as B 663 – 94 (2000). 4 p. This specification covers electrical contact components made from silver-tungsten carbide by powder metallurgical procedures. This specification covers compositions within...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1979. Last previous edition approved in 2000 as B 664 – 81 (2000). 2 p. This specification defines the criteria for composition and other requirements for brushes with a nominal silver content of 80 %, by weight, with the balance being substantially...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published November 2005. Originally approved in 1980. Last previous edition approved in 2000 as B 668 – 00. 2 p. This specification covers UNS N08028 seamless cold-finished or hot finished pipe and tube intended for general corrosive service. The general requirements are covered in...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published June 2005. Originally approved in 1980. Last previous edition approved in 1999 as B 671 – 81 (1999). 2 p. This specification covers refined iridium as sponge and powder in two grades as follows: 1 Grade 99.80 (UNS PO6100)— Iridium having a 2 Grade 99.90— Iridium having a purity of...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2005. Published July 2005. Originally approved in 1980. Last previous edition approved in 2004 as B 673 – 04. 3 p. This specification covers UNS N08925, UNS N08354, and UNS N08926 welded pipe for general corrosion applications. This specification covers pipe sizes in schedules shown in Table 1
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2005. Published July 2005. Originally approved in 1980. Last previous edition approved in 2004 as B 674 – 04. 2 p. This specification covers UNS N08925, UNS N08354, and UNS N08926 welded tube for general corrosion applications. This specification covers outside diameter and nominal wall tube....
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2005. Published July 2005. Originally approved in 1980. Last previous edition approved in 2004 as B 677 – 04a. 3 p. This specification covers UNS N08925, UNS N08354, and UNS N08926 seamless, cold-worked or hot-finished pipe and tube intended for general corrosive service.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1980. Last previous edition approved in 2001 as B 683 – 01. 2 p. This specification covers palladium in the form of rod, wire, strip, and sheet material for electrical contacts. The values stated in inch-pound units are to be regarded as the...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2008. Published June 2008. Originally approved in 1981. Last previous edition approved in 2002 as B 684 – 97 (2002). 3 p. This specification covers an 85 % platinum—15 % iridium alloy, and a 90 % platinum—10 % iridium alloy, in the form of rod, wire, strip, and sheet material for electrical contacts.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1981. Last previous edition approved in 2001 as B 685 – 01. 2 p. This specification covers a 60 % palladium-40 % copper alloy in the form of rod, wire, strip, and sheet material for electrical contacts.
American Society for Testing and Materials (ASTM). Current edition approved Mar. 1, 2005. Published March 2005. Originally approved in 1981. Last previous edition approved in 1999 as B 687 – 99. 6 p. This specification establishes the requirements for brass and copper pipe nipples in standard pipe sizes from 1⁄8 to 8 in., inclusive, in standard lengths, and chromium-plated pipe...
American Society for Testing and Materials (ASTM). Current edition approved Mar. 1, 2005. Published April 2005. Originally approved in 1984. Last previous edition approved in 1999 as B 68M – 99. 5 p. This specification establishes the requirements for bright annealed seamless copper tube suitable for use in refrigeration, oil lines, gasoline lines, and so forth, where tube with an...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published February 2006. Originally approved in 1926. Last previous edition approved in 2001 as B 69 - 01a. 4 p. This specification covers two types of commercial rolled zinc as described in
1.2. It should be understood that the specification is general. Any closer limitations on permissible...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1981. Last previous edition approved in 2000 as B 692 – 90 (2000). 2 p. This specification defines the criteria for composition and other requirements for brushes with a nominal silver content of 75 weight % with the balance being substantially...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1981. Last previous edition approved in 2001 as B 693 – 91 (2001). 3 p. This specification covers electrical contact components made from silver nickel by powder metallurgical procedures. This specification covers compositions within the...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. Published May 2007. Originally approved in 1927. Last previous edition approved in 2001 as B 70 – 90 (2001). 2 p. This test method covers the determination of the change of resistance with temperature of metallic materials for electrical heating, and is applicable over the range of service...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published June 2005. Originally approved in 1982. Last previous edition approved in 2003 as B 705 – 03. 3 p. This specification covers welded UNS N06625, UNS N06219 and UNS N08825 pipe in the annealed condition (temper) for general corrosion applications. This specification covers pipe...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2006. Published February 2006. Originally approved in 1982. Withdrawn Dec. 15, 1993. Reinstated March 10, 2000. Last previous edition approved in 2000 as B 706 – 00. 7 p. This specification establishes the requirements for copper alloy UNS No. C69100 seamless pipe in standard pipe sizes, both...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published November 2005. Originally approved in 1982. Last previous edition approved in 2001 as B 708 – 01. 7 p. This specification covers unalloyed and alloyed tantalum plate, sheet, and strip as follows: 1 R05200, unalloyed tantalum, electron-beam furnace or vacuum-arc melt, or both, 2...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1982. Last previous edition approved in 1999 as B 712 – 93 (1999). 2 p. This guide describes procedures for use in conducting analysis of silver-cadmium oxide materials for sodium and potassium content. The exact methods for the performance of this...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1983. Last previous edition approved in 2000 as B 717 – 96 (2000). 2 p. This specification covers refined ruthenium as sponge and powder in one grade as follows: 1 Grade 99.80—Ruthenium having a purity of 99.80 %. 2 Grade 99.90—Ruthenium having a...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1983. Last previous edition approved in 2000 as B 718 – 00. 8 p. This specification covers wrought alloy UNS N06333 plate, sheet, and strip intended for heat resisting applications and general corrosive service. The values stated in inch-pound...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 1983. Last previous edition approved in 2000 as B 719 - 00. 5 p. This specification covers wrought alloy UNS N06333 in the form of hot-finished and cold-finished bars and flats intended for heat resisting applications and general corrosive service.
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1983. Last previous edition approved in 2002 as B 722 - 02. 2 p. This specification covers alloy N06333 in the form of hot-finished and cold-finished seamless pipe and tube intended for heat-resisting applications and general corrosive service....
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 1983. Last previous edition approved in 2000 as B 723 – 00. 3 p. This specification covers wrought alloy UNS N06333 in the form of welded pipe intended for heat-resisting applications and general corrosive service.
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published June 2005. Originally approved in 1983. Last previous edition approved in 2003 as B 725 – 93 (2003). 6 p. This specification covers nickel (UNS N02200) and low carbon nickel (UNS N02201 and UNS N04400) in the form of welded and annealed or welded and stress relieved pipe intended for...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published December 2006. Originally approved in 1983. Last previous edition approved in 2002 as B 726 – 02. 2 p. This specification covers alloy UNS N06333 in the form of welded tube intended for heat-resisting applications and general corrosive service.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published December 2005. Originally approved in 1984. Last previous edition approved in 2000 as B 729 – 00. 3 p. This specification covers UNS N08020, UNS N08026, and UNS N08024 seamless, cold-worked or hot finished pipe and tube intended for general corrosive service.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1996. Last previous edition approved in 2001 as B 731 – 96 (2001). 2 p. This specification covers 60 % palladium-40 % silver rod, wire, strip, and sheet material for electrical contacts.
ASTM, 97(2013), 4p. B 734 Standard Specification for Electrodeposited Copper for Engineering Uses Brief Summary This specification establishes the requirements for electrodeposited copper coatings used for engineering purposes including surface hardening, heat treatment stop-off, as an underplate for other engineering coatings, for electromagnetic interference shielding in...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published December 2006. Originally approved in 1984. Last previous edition approved in 2005 as B 735 – 05. 4 p. This test method covers equipment and procedures for using nitric acid vapor for determining porosity in gold coatings, greater than 0.6 μm (25 μin.) in thickness, particularly...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published June 2005. Originally approved in 1984. Last previous edition approved in 2001 as B 737 – 01. 4 p. This specification covers hot- or cold-worked hafnium rod and wire, or both. This specification contains two material grades, one specifically for nuclear applications (Grade R1) and...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1985. Last previous edition approved in 2000 as B 742 – 90 (2000). 3 p. This specification covers fine silver grade 99.9 % in fabricated form. The forms covered are tubing, rod, wire, strip, and sheet for electrical contact applications.
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1985. Last previous edition approved in 2000 as B 743 – 00. 6 p. This specification establishes the requirements for seamless copper tube in coils, suitable for use in refrigeration and air conditioning or other uses, such as oil lines and...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. Originally approved in 1985. Last previous edition approved in 2001 as B 752 – 01. 4 p. This specification covers zirconium and zirconium-alloy castings for general corrosion-resistant and industrial applications.
American Society for Testing and Materials (ASTM). Current edition approved Mar. 1, 2005. Published March 2005. Originally appproved in 1986. Last previous edition approved 1999 as B 754 – 89 (1999). 5 p. This test method describes a procedure for the measurement of distortions in thin metal strip and the application of these measurements to an equation that will indicate the...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1986. Last previous edition approved in 2000 as B 755 – 00. 7 p. This specification covers rolled nickel-chromium-molybdenum-tungsten alloys (UNS N06110) plate, sheet, and strip.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1986. Last previous edition approved in 2000 as B 756 – 00. 5 p. This specification covers nickel-chromium-molybdenum-tungsten (UNS N06110) in the form of hot-worked rod and bar and cold-worked rod in the conditions shown in Table 1.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1990. Last previous edition approved in 2000 as B 757 - 00. 5 p. This specification covers welded UNS N06110 pipe in the annealed condition (temper) for general corrosion applications. This specification covers pipe sizes in schedules shown in...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1986. Last previous edition approved in 2000 B 758 – 00. 4 p. This specification covers welded UNS N06110 tube in the annealed condition (temper) for general corrosion applications. This specification covers outside diameter and nominal wall...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1986. Last previous edition approved in 2000 as B 759 - 00. 3 p. This specification2 cover nickel-chromium-molybdenum-tungsten alloys (UNS N06110) in the form of cold-worked seamless pipe and tube in the conditions shown in Table 1. Hot-worked...
American Society for Testing and Materials (ASTM). Current edition approved Mar. 1, 2005. Published March 2005. Originally approved in 1984. Last previous edition approved in 1999 as B 75M – 99. 7 p. This specification establishes the requirements for seamless round, rectangular, and square copper tube suitable for general engineering applications.
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. Published May 2007. Originally approved in 1929. Last previous edition approved in 2001 as B 76 – 90 (2001). 6 p. This test method covers the determination of the resistance to oxidation of nickel-chromium and nickelchromium-iron electrical heating alloys at elevated temperatures under...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 1987. Last previous edition approved in 2002 as B 770 – 02. 5 p. This specification establishes requirements for copper-beryllium alloy sand castings for general applications and nominal compositions alloys defined by this specification are shown in...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published February 2006. Originally approved in 1987. Last previous edition approved in 2000 as B 774 - 00. 4 p. This specification covers low-melting point metal alloys and soldiers, including bismuth–tin, bismuth–lead, bismuth–tin–lead, bismuth–tin–lead–cadmium,...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2006. Published September 2006. Originally approved in 1987. Last previous edition approved in 2001 as B 776 – 01a. 9 p. This specification covers two grades of wrought hafnium and hafnium alloy strip, sheet, and plate as follows: 1 Grade R1 for nuclear applications, and 2 Grade R3 for...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. Published May 2007. Originally approved in 1959. Last previous edition approved in 2001 as B 78 – 90 (2001). 5 p. This test method covers the determination of the resistance to oxidation of iron-chromium-aluminum electrical heating alloys at elevated temperatures under intermittent heating...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1987. Last previous edition approved in 1999 as B 781 – 93a (1999). 5 p. This guide provides guidelines for users and manufacturers of silver-cadmium oxide material produced in strip, rod, wire, and part form for electrical contact applications.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published November 2005. Originally approved in 1988. Last previous edition approved in 2001 as B 792 – 01. 3 p. This specification covers commercial zinc alloys in ingot form for remelting for the manufacture of castings from the alloys as specified and designated as shown in Table 1.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published February 2006. Originally approved in 1988. Last previous edition approved in 2000 as B 798 – 95 (2000). 6 p. This test method covers equipment and techniques for determining porosity in noble metal coatings, particularly electrodeposits and clad metals used on electrical contacts.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published November 2005. Originally approved in 1988. Last previous edition approve in 2000 as B 799 – 95 (2000). 4 p. This test method covers equipment and methods for determining the porosity of gold and palladium coatings, particularly electrodeposits and clad metals used on electrical...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1990. Last previous edition approved in 2002 as B 805 – 02. 7 p. This specification covers nickel alloys UNS N07716, N07725, N07773, N07776, N09777, and N09925 in the form of hot or cold finished rounds, squares, hexagons, rectangles, and cold...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1990. Last previous edition approved in 2005 as B 806 – 05. 3 p. This specification establishes requirements for copper alloy permanent mold castings for general applications. Nominal compositions of the alloys under this specification are shown...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published June 2005. Originally approved in 1997. Last previous edition approved in 2003 as B 808 – 97 (2003). 4 p. This test method monitors the reactivity of a gaseous test environment in which metal surfaces (for example, electrical contacts, assembled printed wiring boards, and so forth)...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published December 2006. Originally approved in 1991. Last previous edition approved in 2001 as B 810 – 01a. 6 p. This test method covers the calibration of atmospheric corrosion test chambers for electrical contacts that produce an adherent film of corrosion product on copper, such as a test...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1991. Last previous edition approved in 2002 as B 814 – 02. 3 p. This specification covers nickel-chromium-iron-molybdenum-tungsten alloy UNS N06920 in the form of rolled plate, sheet, and strip for general corrosion service.
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published December 2006. Originally approved in 1991. Last previous edition approved in 2002 as B 815 – 02. 3 p. This specification covers cobalt-chromium-nickel-molybdenum-tungsten alloy UNS R31233 in the form of rod for wear applications and general corrosion service.
American Society for Testing and Materials (ASTM). Current edition approved March 15, 2006. Published April 2006. Originally approved in 1992. Last previous edition approved in 2000 as B 819 – 00. 7 p. This specification establishes the requirements for two wall thickness schedules of specially cleaned, straight lengths of seamless copper tube, identified as Types K and L,...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published June 2005. Originally approved in 1992. Last previous edition approved in 2003 as B 827 - 97 (2003). 9 p. This practice provides procedures for conducting environmental tests involving exposures to controlled quantities of corrosive gas mixtures. This practice provides for the...
This specification contains various requirements that, with the exception of Sections 5 and 10, are mandatory requirements to the ASTM nickel and nickel alloy, seamless pipe and tube specifications described in section 1.
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1993. Last previous edition approved in 2005 as B 833 - 05. 5 p. This specification covers zinc and zinc alloy wire used to deposit zinc coatings by thermal spraying (metallizing) for the corrosion protection of steel and iron. Zinc and zinc...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2006. Published December 2006. Originally approved in 1993. Last previous edition approved in 2006 as B 846 – 06. 13 p. The terms defined in this terminology standard are applicable to copper and copper alloy products specifications, test methods, practices, and other documents within the...
American Society for Testing and Materials (ASTM). Current edition approved March 15, 2006. Published March 2006. Originally approved in 1995. Last previous edition approved in 2001 as B 858 – 01. 4 p. This test method describes a procedure to determine the presence of residual stresses in wrought copper alloy products that may lead to stress corrosion cracking. An ammonia vapor...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2006. Published August 2006. Originally approved in 1931. Last previous edition approved in 2005 as B 86 - 05. 8 p. This specification covers commercial zinc, zincaluminum castings and continuous cast bar stock, as designated and specified in Table 1 seven alloy.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published December 2005. Originally approved in 1995. Last previous edition approved in 2002 as B 860 - 02. 3 p. This specification covers zinc master alloys which are used in hot dip galvanizing for the purpose of adjusting the concentration of certain alloying elements in the molten zinc...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1995. Last previous edition approved in 2006 as B 861 – 06. 8 p. This specification covers the requirements for 34 grades of titanium and titanium alloy seamless pipe intended for general corrosion resisting and elevated temperature service.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2006. Published October 2006. Originally approved in 1995. Last previous edition approved in 2006 as B 862 – 06a. 9 p. This specification covers the requirements for 33 grades of titanium and titanium alloy welded pipe intended for general corrosion resisting and elevated temperature service.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1995. Last previous edition approved in 2006 as B 863 – 06. 6 p. This specification covers the requirements for 38 grades of titanium and titanium alloy wire
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published January 2007. Originally approved in 1996. Last previous edition approved in 2003 as B 872 – 96 (2003). 7 p. This specification covers rolled precipitation hardenable nickel-iron-chromium-columbium (Nb)-titanium-aluminum alloy (N09908) plate, sheet, and strip in the annealed...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published October 2005. Originally approved in 1997. Last previous edition approved in 2000 as B 882 – 00. 4 p. This specification covers the establishment of the requirements for pre-patinated (artificially aged) copper sheet and strip in ounce-weight thicknesses supplied in flat lengths for...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published June 2005. Originally approved in 1997. Last previous edition approved in 2001 as B 884 - 01. 6 p. This specification covers niobium-titanium alloy billets, bars, and rods, at 46 to 48 % titanium. This material is used in the manufacture of wire for superconducting applications
American Society for Testing and Materials (ASTM). Current edition approved March 15, 2006. Published March 2006. Originally approved in 1998. Last previous edition approved in 2004 as B 888 – 04. 13 p. This specification establishes the requirements for copper alloy strip for use in the manufacture of electrical connectors or spring contacts produced from one of the following...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published October 2005. Originally approved in 1983. Last previous edition approved in 2003 as B 88M – 03. 7 p. This specification covers seamless copper water tube suitable for general plumbing, similar applications for the conveyance of fluids, and commonly used with solder, flared, or...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published November 2005. Originally approved in 1999. Last previous edition approved in 1999 as B 896 - 99. 6 p. These test methods define procedures for the relative characterization of conductor material connectability on the basis of measurements of parameters important to the design and...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published June 2005. Originally approved in 1999. Last previous edition approved in 1999 as B 898 – 99. 7 p. This specification covers plate consisting of a base metal to which is bonded, integrally and continuously, on one or both sides a layer of one of the following: titanium, zirconium,...
ASTM B 899 – 06 Standard Terminology Relating to Non-ferrous Metals and Alloys American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published December 2006. Originally approved in 1999. Last previous edition approved in 2005 as B 899 – 05. 7 p. To promote precise understanding and interpretation of standards, reports, and other technical...
American Society for Testing and Materials (ASTM). Current edition approved Mar. 1, 2005. Published March 2005. Originally approved in 2000. Last previous edition approved in 2000 as B903–00. 5 p. This specification establishes the requirements for seamless, internally enhanced copper tube, in straight lengths or coils, suitable for use in refrigeration and air-conditioning...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published December 2006. Originally approved in 2000. Last previous edition approved in 2002 as B 906 - 02. 16 p. This specification covers a group of general requirements that, unless otherwise specified in the purchase order or in an individual specification, shall apply to rolled nickel...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published December 2005. Originally approved in 2000. Last previous edition approved in 2004 as B 907 – 04. 6 p. This specification covers solder metal alloys (commonly known as soft solders), including zinc-aluminum, zincaluminum-copper, zinc-tin, zinc-tin-copper, zinc-cadmium-tin,...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published November 2005. Originally approved in 2000. Last previous edition approved in 2000 as B 913 – 00. 5 p. This test method establishes the requirements for a standardized method of evaluating the quality of crimped-type electrical connections to solid or stranded conductors. This test...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published November 2006. Originally approved in 2001. Last previous edition approved in 2001 as B 919 – 01. 7 p. This specification establishes the requirements for welded, internally enhanced copper tube, in straight lengths or coils, suitable for use in refrigeration and air conditioning...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published December 2006. Originally approved in 2001. Last previous edition approved in 2001 as B 920 - 01. 4 p. This test practice covers equipment and methods for revealing the porosity of gold and palladium coatings, particularly electrodeposits and clad metals used on electrical...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published December 2006. Originally approved in 2002. Last previous edition approved in 2002 as B 924 - 02. 5 p. This specification describes seamless and welded nickel alloy tubing on which the external or internal surface, or both, has been modified by a cold forming process to produce an...
American Society for Testing and Materials (ASTM). Current edition approved March 15, 2006. Published March 2006. Originally approved in 1934. Last previous edition approved in 2001 as B 96/B 96M – 01. 4 p. This specification establishes the requirements for copper-silicon alloy plate, sheet, strip, and rolled bar for drawing, forming, stamping, bending, and general engineering...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2006. Published February 2006. Originally approved in 1935. Last previous edition approved in 2001 as B 99/B 99M – 01. 3 p. This specification establishes the requirements for round, rectangular, and square wire for general applications other than for electrical transmission cable. The alloys...
ASTM standard B92/B92M. Standard Specification for Unalloyed Magnesium Ingot and Stick For Remelting. 2001, 2 p. Стандарт США B92/B92M. Чистый магний в чушках и слитках для переплавки. Издание ASTM 2001 г. United States. 2 стр. Регламентирует требования к химическому составу первичного магния в чушках марок 9980A, 9980B, 9990A, 9995A и 9998A.
American Society for Testing and Materials (ASTM). Current edition approved Oct. 15, 2006. Published November 2006. Originally approved in 1985. Last previous edition approved in 2001 as C1036 – 01. 8 p. This specification covers the requirements for annealed, monolithic flat glass supplied as cut sizes or stock sheets. This specification is applicable for laboratory and field...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 1985. Last previous edition approved in 2000 as C 1040 – 00. 5 p. These test methods cover the determination of the in-place density of unhardened and hardened concrete, including roller compacted concrete, by gamma radiation. For notes on the...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published January 2005. Originally approved in 1986. Last previous edition approved in 2004 as C 1064 – 04. 3 p. This test method covers the determination of temperature of freshly mixed hydraulic-cement concrete. The values stated in inch-pound or SI units are to be regarded separately as...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published July 2005. Originally approved in 1987. Last previous edition approved in 2005 as C 1077 – 05. 7 p. This practice identifies and defines the duties, responsibilities, and minimum technical requirements of testing laboratory personnel and the minimum technical requirements for...
American Society for Testing and Materials (ASTM). Current edition approved October 1, 2003. Published October 2003. Originally published in 1988. Last previous edition approved in 2003 as C 1091 – 03. 2 p. This test method defines procedures for hydrostatic infiltration testing of new installations of vitrified clay pipe lines, to demonstrate the structural integrity of the...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 1989. Last previous edition approved in 2002 as C 1105 – 95(2002). 4 p. This test method covers the determination, by measurement of length change of concrete prisms, the susceptibility of cement-aggregate combinations to expansive alkali-carbonate...
American Society for Testing and Materials (ASTM). Current edition approved August 15, 2005. Published August 2005. Originally approved in 1991. Last previous edition approved in 2002 as C 1107 – 02. 5 p. This specification covers packaged dry, hydraulic cement grout (nonshrink) intended for use under applied load (such as to support a structure, a machine, and the like) where a...
American Society for Testing and Materials (ASTM). Current edition approved July 15, 2005. Published August 2005. Originally approved in 1990. Last previous edition approved in 1997 as C 1137 – 97. 4 p. This test method provides a procedure for indicating the relative degree to which a fine aggregate is likely to degrade due to the mixing and agitation of hydraulic cement concrete.
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 1991. Last previous edition approved in 1997 as C 1202 – 97. 6 p. This test method covers the determination of the electrical conductance of concrete to provide a rapid indication of its resistance to the penetration of chloride ions. This test...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 1993. Last previous edition approved in 2004 as C 1240-04. 7 p. This specification covers silica fume for use in concrete and other systems containing hydraulic cement. In the cases of slurried or densified silica fume, perform the tests on the...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 1989. Last previous edition approved in 2001 as C 1260 – 01. 5 p. This test method permits detection within 16 days of the potential for deleterious alkali-silica reaction of aggregate in mortar bars.
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published September 2007. 6 p. This test method covers the determination of the average density of a quantity of coarse aggregate particles (not including the volume of voids between the particles), the relative density (specific gravity), and the absorption of the coarse aggregate. Depending...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published September 2007. 7 p. This test method covers the determination of the average density of a quantity of fine aggregate particles (not including the volume of voids between the particles), the relative density (specific gravity), and the absorption of the fine aggregate. Depending on...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 1995. Last previous edition approved in 2001 as C 1293 – 01. 6 p. This test method covers the determination, by measurement of length change of concrete prisms, of the susceptibility of an aggregate for participation in expansive alkali-silica...
American Society for Testing and Materials (ASTM). Current edition approved August 1, 2006. Published August 2006. 4 p. This test method covers a procedure for testing sizes of coarse aggregate smaller than 37.5 mm (11⁄2 in.) for resistance to degradation using the Los Angeles testing machine.
2005. Published October 2005. 4 p. This specification covers three types of mortar cement for use where mortar for masonry is required. Mortar cements are classified as Type N, S, or M, according to the physical requirements prescribed in Table 1. Mortar cement shall conform to the applicable requirements prescribed in Table 1 for its classification.
American Society for Testing and Materials (ASTM). Current edition approved Feb. 15, 2006. Published March 2006. 5 p. This test method covers the determination of the particle size distribution of fine and coarse aggregates by sieving. Some specifications for aggregates which reference this test method contain grading requirements including both coarse and fine fractions....
American Society for Testing and Materials (ASTM). Current edition approved April 10, 2003. Published May 2003. Orginally approved in 1997. Last previous edition approved in 1997 as C1376–97. 3 p. This specification covers the optical and aesthetic quality requirements for coatings applied to glass for use in building glazing. The coatings covered are applied to the glass using...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2010. Published August 2010. 4 p. This test method covers determination of the density of freshly mixed concrete and gives formulas for calculating the yield, cement content, and air content of the concrete. Yield is defined as the volume of concrete produced from a mixture of known quantities of...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2010. Published March 2010. 4 p. This test method covers determination of slump of hydraulic-cement concrete, both in the laboratory and in the field.
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 1999. Last previous edition approved in 1999 as C 1435 – 99. 5 p. This practice covers molding cylindrical test specimens from concrete when the standard procedures of rodding and internal vibration, as described in Practice C 31/C 31M and Practice C...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published June 2005. Originally approved in 2000. Last previous edition approved in 2000 as C 1480 – 00. 4 p. This specification covers laboratory performance standards for pre-blended, dry, packaged, combined materials for use in wet or dry shotcrete applications that are delivered to a...
American Society for Testing and Materials (ASTM). Current edition approved May I, 2007. Published June 2007. 10 р. This specification covers eight types of portland cement, as follows: Type I-For use when the special properties specified for any other type are not required. Type IA-Air-entraining cement for the same uses as Type I, where air-entrainment is desired. Type II-For...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2011. Published July 2011. Originally approved in 2002. Last previous edition approved in 2009 as C 1540-09a. 5 p. This specification covers the evaluating of the performance of heavy duty shielded couplings to join hubless cast iron soil pipe and fittings. Couplings covered by this standard...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 2002. Last previous edition approved in 2004 as C 1550-04. 13 p. This test method covers the determination of flexural toughness of fiber-reinforced concrete expressed as energy absorption in the post-crack range using a round panel supported on...
American Society for Testing and Materials (ASTM). Current edition approved March 1, Published April 2005. 3 p. This test method is for the determination of watersoluble sulfate 2005. in soils. This test method was developed for concentrations of water-soluble sulfate in soils between 0.02 and 3.33 % sulfate by mass. This test method does not determine sulfur in any form except...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2005. Published April 2005. Originally approved in 2004. Last previous edition approved in 2004 as C 1586 – 04. 3 p. This document provides guidance regarding the proper use of Specification C 270 and Test Method C 780 for evaluating masonry mortar produced in the laboratory and at the construction...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 2004. Last previous edition approved in 2004 as C 1602/C 1602M – 04. 4 p. This specification covers the compositional and performance requirements for water used as mixing water in hydraulic cement concrete. It defines sources of water and provides...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 2004. Last previous edition approved in 2005 as C 1603 – 05. 4 p. This test method covers the measurement of the solids content in water for use as mixing water in ready-mixed concrete and the measurement of its density. Solids content is...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published January 2005. 5 p. This test method covers obtaining, preparing, and testing cores drilled from shotcrete for length, compressive strength, or splitting tensile strength determinations. The values stated in either inch-pound units or SI units shall be regarded separately as...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2009. Published November 2009. 9 p. This guide covers recommended installation techniques for flexible closed cell pre-formed insulation in tube or sheet form. This guide is applicable to materials manufactured in accordance with Specification C534 (Elastomeric based insulation) or Specification...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1. 2004. Published November 2004. 24p. This test method establishes the criteria for the laboratory measurement of the steady-state heat flux through flat, homogeneous specimen(s) when their surfaces are in contact with solid, parallel boundsries held at constant temperatnres using the...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2010. Published June 2010. 3 p. This test method covers the determination of the normal consistency of hydraulic cement. This test method is intended to be used to determine the amount of water required to prepare hydraulic cement pastes for testing
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2009. Published January 2010. 3 p. This test method covers the determination of the density of hydraulic cement. Its particular usefulness is in connection with the design and control of concrete mixtures. The density of hydraulic cement is defined as the mass of a unit volume of the solids.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2008. Published July 2008. 8 p. These test methods determine the time of setting of hydraulic cement by means of the Vicat needle. Two test methods are given; Method A is the Reference Test Method using the manually operated standard Vicat apparatus, while Method B permits the use of an automatic...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published September 2007. 8 p. This practice covers procedures for making and curing test specimens of concrete in the laboratory under accurate control of materials and test conditions using concrete that can be consolidated by rodding or vibration as described herein
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2010. Published June 2010. Originally approved in 1947. Last previous edition approved in 2007 as C216 – 07a. 13 p. This specification covers brick intended for use in masonry and supplying structural or facing components, or both, to the structure. The property requirements of this...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2008. Published August 2008. 6 p. This specification covers requirements for the flow table and accessory apparatus used in making flow tests for consistency of mortars in tests of hydraulic cement, such as but not limited to Test Method C1437.
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2010. Published November 2010. 10 p. This test method covers determination of the air content of freshly mixed concrete from observation of the change in volume of concrete with a change in pressure. This test method is intended for use with concretes and mortars made with relatively dense...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2009. Published July 2009. 5 p. These test methods cover the determination of the relative quantity of mixing water that will bleed from a sample of freshly mixed concrete. Two test methods, that differ primarily in the degree of vibration to which the concrete sample is subjected, are included.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2010. Published July 2010. 14 p. This specification covers mortars for use in the construction of non-reinforced and reinforced unit masonry structures. Four types of mortar are covered in each of two alternative specifications: (1) proportion specifications and (2) property specifications.
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2009. Published January 2010. 5 p. This test method covers the determination of bulk density (unit weight) of aggregate in a compacted or loose condition, and calculated voids between particles in fine, coarse, or mixed aggregates based on the same determination. This test method is applicable to...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2010. Published September 2010. 3 p. This test method covers determination of the flexural strength of concrete specimens by the use of a simple beam with center-point loading. It is not an alternative to Test Method C78/C78M.
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published January 2005. Originally approved in 1952. Last previous edition approved in 2004 as C 294 – 04. 10 p. This descriptive nomenclature provides brief descriptions of some of the more commonly occurring, or more important, natural and artificial materials of which mineral aggregates...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2006. Published August 2006. 3 p. This practice covers the mechanical mixing of hydraulic cement pastes and mortars of plastic consistency. This practice is intended for use in the mechanical mixing of pastes and mortars for the testing of hydraulic cements.
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 1954. Last previous edition approved in 2003 as C 341 – 03a. 4 p. This practice covers the determination of the length changes of cast, drilled, or sawed specimens of hydraulic-cement mortar and concrete due to causes other than externally applied...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2008. Published January 2009. 4 p. This test method covers the determination of the compressive strength of hydraulic-cement mortars, using for the test specimens portions of prisms made and broken in flexure in accordance with Test Method C348.
American Society for Testing and Materials (ASTM). Current edition approved Dec. 15, 2009. Published February 2010. 7 p. This test method covers determination of compressive strength of cylindrical concrete specimens such as molded cylinders and drilled cores. It is limited to concrete having a density in excess of 800 kg/m3 [50 lb/ft3].
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2004. Published January 2004. 2 p. This test method covers two procedures for an approximate determination of the presence of injurious organic impurities in fine aggregates that are to be used in hydraulic cement mortar or concrete. One procedure uses a standard color solution and the other uses a...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2008. Published May 2008. 7 p. This test method covers the determination of the time of setting of concrete, with slump greater than zero, by means of penetration resistance measurements on mortar sieved from the concrete mixture. This test method is suitable for use only when tests of the...
American Society for Testing and Materials (ASTM). Current edition approved April 10, 2002. Published June 2002. 11 p. This test method covers the measurement of sound absorption in a reverberation room by measuring decay rate. Procedures for measuring the absorption of a room, the absorption of an object, such as an office screen, and the sound absorption coefficients of a...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 1959. Last previous edition approved in 2002 as C 441–02a. 3 p. This test method covers the determination of the effectiveness of pozzolans or slag in preventing the excessive expansion caused by reaction between aggregates and alkalies in portland...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 10, 2002. Published October 2002. 5 p. This test method covers determination of (1) chord modulus of elasticity (Young’s) and (2) Poisson’s ratio of molded concrete cylinders and diamond-drilled concrete cores when under longitudinal compressive stress. Chord modulus of elasticity and Poisson’s ratio...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2010. Published November 2010. Originally approved in 1961. Last previous edition approved in 2002 as C469 –
02. This test method covers determination of chord modulus of elasticity (Young’s) and Poisson’s ratio of molded concrete cylinders and diamond-drilled concrete cores when under...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 1962. Last previous edition approved in 2004 as C 494 – 04. 10 p. This specification covers materials for use as chemical admixtures to be added to hydraulic-cement concrete mixtures in the field for the purpose or purposes indicated for the seven...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2004. Published March 2004. 5 p. This test method covers the determination of the splitting tensile strength of cylindrical concrete specimens, such as molded cylinders and drilled cores
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 1968. Last previous edition approved in 2003 as C 511 – 03. 3 p. This specification includes requirements for mixing rooms where paste and mortar specimens are prepared; and for moist cabinets, moist rooms, and water storage tanks where paste, mortar,...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2009. Published February 2010. Originally approved in 1963. Last previous edition approved in 2003 as C522 – 03. 6 p. This test method covers the measurement of airflow resistance and the related measurements of specific airflow resistance and airflow resistivity of porous materials that can be...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2009. Published August 2009. 3 p. This test method covers testing sizes of coarse aggregate larger than 19 mm (3⁄4 in.) for resistance to degradation using the Los Angeles testing machine. This test is a measure of degradation of mineral aggregates of standard gradings resulting from a...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2005. Published February 2005. Originally approved in 1965. Last previous edition approved in 2004 as C 567 – 04. 3 p. This test method provides procedures to determine the oven-dry and equilibrium densities of structural lightweight concrete.
ASTM, 2010, 9p. C585 Standard Practice for Inner and Outer Diameters of Thermal Insulation for Nominal Sizes of Pipe and Tubing
Significance and Use
The purpose of this practice is to ensure satisfactory fit on standard sizes, to accommodate radial expansion of pipes and tubes which are heated after being insulated, and to minimize the number of insulation sizes and...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1966. Last previous edition approved in 1999 as C 586 – 99. 5 p. This test method covers the determination of the expansion of a specimen of carbonate rock while immersed in a solution of sodium hydroxide (NaOH) at room temperature. The length...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 15, 2009. Published February 2010. 4 p. This test method covers the determination of the propagation velocity of longitudinal stress wave pulses through concrete. This test method does not apply to the propagation of other types of stress waves through concrete.
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published July 2005. Originally approved in 1968. Last previous edition approved in 2003 as C 618–03. 3 p. This specification covers coal fly ash and raw or calcined natural pozzolan for use in concrete where cementitious or pozzolanic action, or both, is desired, or where other properties...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2009. Published June 2009. Originally approved in 1970. Last previous edition approved in 2007 as C 655 – 07. 6 p. This specification covers reinforced concrete pipe designed for specific D-loads and intended to be used for the conveyance of sewage, industrial wastes, and storm water and for the...
Scope - These lest methods cover procedures for the chemical, mass spectrometric, and spectrochemical analysis of nuclear-grade uranium dioxide powders and pellets to determine compliance with specifications. Current edition approved Sept 1, 2011. Published October 2011. Originally approved in 1972. Last previous edition approved in 2005 as C696-99 (2005). DOI: 10.1520/C0696-11.
Scope - These test methods cover procedures for the chemical, mass spectrometric, and spectrochemical analysis of nuclear-grade uranium dioxide powders and pellets to determine compliance with specifications.
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2010. Published September 2010. 4 p. This test method covers the determination of the flexural strength of concrete by the use of a simple beam with third-point loading.
American Society for Testing and Materials (ASTM). Current edition approved Dec. 15, 2006. Published February 2007. Originally approved in 1974. Last previous edition approved in 2006 as C 780 – 06. 17 p. This test method covers procedures for the sampling and testing of mortars for composition and for their plastic and hardened properties, either before or during their actual use...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2008. Published September 2008. 3 p. This test method covers the determination of a rebound number of hardened concrete using a spring-driven steel hammer.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2008. Published July 2008. 3 p. This test method covers the determination of the time of setting of hydraulic cement mortar by means of the modified Vicat needle. The purpose of this test method is to establish whether or not a cement complies with a specification limit on time of setting. It...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published July 2005. Originally approved in 1931. Last previous edition approved in 2004 as C 87 – 04. 4 p. This test method covers the determination of the effect on mortar strength of the organic impurities in fine aggregate, whose presence is indicated using Test Method C
40. Comparison...
American Society for Testing and Materials (ASTM). Current edition approved July 15, 2005. Published August 2005. 5 p. This test method covers the testing of aggregates to estimate their soundness when subjected to weathering action in concrete or other applications. This is accomplished by repeated immersion in saturated solutions of sodium or magnesium sulfate followed by oven...
American Society for Testing and Materials (ASTM). Current edition approved Feb. l. 2005. Published April 2005. Originally approved in 1931. Last previous edition approved in 2003 as C 90-03. 4 p. This specification covers hollow and solid concrete masonry units made from hydraulic cement, water, and mineral aggregates with or without the inclusion of other materials. There are...
American Society for Testing and Materials (ASTM). Current edition approved June l. 2009. Published June 2009. Originally approved in 1931. Last previous edition approved in 2008 as C 90-08. 4 p. This specification covers hollow and solid concrete masonry units made from hydraulic cement, water, and mineral aggregates with or without the inclusion of other materials. There are...
American Society for Testing and Materials (ASTM). Current edition approved September 15. 2005. Published October 2005. Originally approved in 1932. Last previous edition approved in 2003 as C 91-03a. 4 p. This specification covers three types of masonry cement for use where mortar for masonry is required. The values stated in SI units are to be regarded as the standard. Values...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2011. Published November 2011. 10 p. This specification covers the requirements for the appli- cation of full thickness portland cement-based plaster for exterior (stucco) and interior work. This specification sets forth tables for proportioning of various plaster mixes and plaster thickness.
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 1980. Last previous edition approved in 2000 as C 928 – 00. 4 p. This specification covers packaged, dry, cementitious mortar or concrete materials for rapid repairs to hardened hydraulic-cement concrete pavements and structures. Materials that...
American Society for Testing and Materials (ASTM). Current edition approved July 10, 1999. Published September 1999. Originally approved in 1980. Last previous edition approved in 1990 as C 944 – 90a. 4 p. This test method covers a procedure for determining the resistance of either concrete or mortar to abrasion. This test method is similar to Procedure B of Test Method C 779/C...
Copyright by ASTM Int'l Fri Jul EDT 2019. — 6 p. Scope - These test methods cover procedures for the analysis of sintered gadolinium oxide-uranium dioxide pellets to determine compliance with specifications. Current edition approved Jan. 1, 2012. Published February 2012. Originally approved in 1981. Last previous edition approved in 2006 as C968-06. DOI: 10.1520/C0968-12.
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published January 2005. Originally approved in 1982. Last previous edition approved in 2004 as C 979–04. 5 p. This specification covers the basic requirement for colored and white pigments in powder form to be used as admixtures in concrete for the purpose of producing integrally colored...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published January 2005. Originally approved in 1982. Last previous edition approved in 2004 as C 989 – 04. 5 p. This specification covers three strength grades of finely ground granulated blast-furnace slag for use as a cementitious material in concrete and mortar.
American Society for Testing and Materials. Reapproved edition, 2005.- 9 p. This guide briefly describes the state-of-the-art of radiation monitors for detecting special nuclear material (SNM) in order to establish the context in which to write performance standards for the monitors. This guide extracts information from technical documentation to provide information for...
American Society for Testing and Materials - 2010.- 16 p. This test method covers the transmission-corrected nondestructive assay (NDA) of gamma-ray emitting special nuclear materials (SNMs), most commonly 235U, 239Pu, and 241Am, in low-density scrap or waste, packaged in cylindrical containers. The method can also be applied to NDA of other gamma-emitting nuclides including...
American Society for Testing and Materials. Reapproved edition - 2005.- 16 p. These test methods cover procedures for the chemical, mass spectrometric, and spectrochemical analysis of nuclear-grade uranium dioxide powders and pellets to determine compliance with specifications. Referenced Documents ASTM Standards: C753 Specification for Nuclear-Grade, Sinterable Uranium Dioxide...
American Society for Testing and Materials, 2004.- 36 p. These test methods cover procedures for subsampling and for chemical, mass spectrometric, spectrochemical, nuclear, and radiochemical analysis of uranium hexafluoride (UF6). Most of these test methods are in routine use to determine conformance to UF6 specifications in the Enrichment and Conversion Facilities. Referenced...
American Society for Testing and Materials, 2004.- 24 p. These test methods cover procedures for the chemical, mass spectrometric, and spectrochemical analysis of nuclear-grade boron carbide powder and pellets to determine compliance with specifications. Referenced Documents ASTM Standards: C750 Specification for Nuclear-Grade Boron Carbide Powder C751 Specification for...
American Society for Testing and Materials, 2013.- 5 p. This terminology standard contains terms, definitions, descriptions of terms, nomenclature, and explanations of acro-nyms and symbols specifically associated with standards under the jurisdiction of Committee C26 on Nuclear Fuel Cycle. This terminology may also be applicable to documents not under the jurisdiction of...
American Society for Testing and Materials, 2017.- 4 p. This practice covers the sampling of surface soil for the purpose of obtaining a sample representative of a particular area for subsequent Chemical analysis of selected radionuclides. This practice describes one acceptable approach to collect soil samples for radiochemical analysis. Referenced Documents ASTM Standards:...
American Society for Testing and Materials, 2017.- 3 p. This practice covers the preparation of surface soil samples collected for analysis of radionuclide constituents, particularly uranium and plutonium. This practice describes one acceptable approach to the preparation of soil samples for radiochemical analysis. Referenced Documents ASTM Standards: C859 Terminology Relating...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 15, 1995. Published April 1995. Originally published 1949. Last previous edition D 1005 – 84 (1990). 3 p. This test method covers the measurement of film thickness of dried films of paint, varnish, lacquer, and related products using micrometers. Procedures A and B utilize stationary micrometers and...
American Society for Testing and Materials (ASTM). Current edition approved June 10, 2001. Published August 2001. Originally published as D 1006 – 51 T. Last previous edition D 1006 – 93. 7 p. This practice covers procedures to be followed for direct exposure of house and trim paints on new, previously unpainted wood materials to the environment. When originators of a weathering...
Current edition approved May 1, 2014. Published May 2014. Originally approved in 1949. Last previous edition approved in 2009 as D1052 – 09. — 4 p. This test method covers a test for measuring the cut growth in rubber vulcanizates subjected to repeated bend flexing.
Current edition approved Dec. 1, 2012. Published February 2013. Originally approved in 1943. Last previous edition approved in 2007 as D1053 – 92a (2007). — 9 p. These test methods describe the use of a torsional apparatus for measuring the relative low temperature stiffeningof flexible polymeric materials and fabrics coated therewith. A routine inspection and acceptance...
Current edition approved Dec. 15, 2015. Published January 2016. Originally approved in 1949. Last previous edition approved in 2014 as D1076 – 14. — 13 p. This specification covers requirements for first grade concentrated natural rubber latex (see Table 1) of the following categories: Category 1—Centrifuged Hevea natural latex preserved with ammonia only or by formaldehyde...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2007. Published January 2008. 4 p. This test method describes the procedure for determining the ductility of a bituminous material measured by the distance to which it will elongate before breaking when two ends of a briquet specimen of the material, of the form described in Section 4, are pulled...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2006. Published January 2007. 4 p. These test methods cover determination of the amount of material finer than a 75-μm (No. 200) sieve by washing. Two methods for determining the amount of material finer than the No. 200 sieve are provided. The method to be used shall be specified by the...
Current edition approved Jan. 1, 2013. Published February 2013. Originally approved in 1951. Last previous edition approved in 2007 as D1148 – 07a. — 4 p. This test method covers techniques to evaluate the surface discoloration of white or light-colored vulcanized rubber that may occur when subjected to UV or UV/visible exposure from specified sources under controlled conditions...
Current edition approved Jan. 1, 2016. Published February 2016. Originally approved in 1951. Last previous edition approved in 2015 as D1149 – 15. — 13 p. These test methods are used to estimate the effect of exposure, under surface tensile strain conditions, either dynamic or static, in an atmosphere containing specified levels of ozone concentration, expressed as partial...
American Society for Testing and Materials (ASTM). Current edition approved May 10, 2003. Published June 2003. Originally approved in 1951. Withdrawn December 2002 and reinstated as D 1155 – 03. 3 p. This test method covers the determination of the percent of true spheres in glass spheres used for retroreflective marking purposes and industrial uses. This test method includes...
США ASTM International Актуальный стандарт 2016 год Стандартный метод испытаний округлости стеклянных сфер имеет отношение к испытаниям шин и является подстандартом Standard Test Method for Roundness of Glass Spheres
Standard Test Method for Bromine Numbers of Petroleum Distillates and Commercial Aliphatic Olefins by Electrometric Titration; ASTM International, 2012. — Официальный перевод выполнен: ФБУ «КВФ «ИНТЕРСТАНДАРТ».— Москва 2012. — 26 с. Этот метод испытаний охватывает определение количества брома в следующих материалах: Нефтяные дистилляты, которые практически не содержат материала...
Current edition approved Jan. 1, 2016. Published January 2016. Originally approved in 1951. Last previous edition approved in 2015 as D1171 – 15. — p. This test method permits the estimation of the relative ability of rubber compounds used for applications requiring resistance to outdoor weathering. This test method is not applicable to materials ordinarily classed as hard rubber,...
American Society for Testing and Materials (ASTM). 2006, 5p. Re approved in 2011.
Brief summary
This specification describes the required characteristics of reagent waters. Four types of waters have been specified, with three additional grades that can be applied to the four types. The grade specifications specifically address contaminants of microbiological origin....
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1952. Last previous edition approved in 1999 as D 1200 – 94 (1999). 4 p. This test method covers the determination of the viscosity of Newtonian or near-Newtonian paints, varnishes, lacquers, and related liquid materials with the Ford-type efflux...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2007. Published March 2007. Originally approved in 1952. Last previous edition approved in 2002 as D 1204 - 02. 2 p. This test method covers the measurement of changes in linear dimensions of nonrigid thermoplastic sheeting or film that result from exposure of the material to specified conditions...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published April 2005. Originally approved in 1952. Last previous edition approved in 2004 as D 1210 – 96 (2004). 12 p. This test method covers measurement of the degree of dispersion (commonly referred to as fineness of grind) of the pigment in a pigment-vehicle system such as liquid...
This terminology defines the technical terms used in standards that are the responsibility of Committee D05 on Coal and Coke. The terms are used in: 1.1.1 The sampling of coal and coke under conditions required for most commercial and technical purposes related to coal and coke. 1.1.2 Bias and related statistical testing, 1.1.3 The description of coal, both visually in the field...
Current edition approved June 15, 2015. Published September 2015. Originally approved in 1952. Last previous edition approved in 2008 as D1229 – 03 (2008). — 3 p. This test method covers evaluation of the ability of vulcanized rubbers that have been compressed at room temperature and then subjected to low temperature (air or carbon dioxide atmosphere), to recover from deformation...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2004. Published April 2004. 13 p. This test method covers measurement of the rate of extrusion of molten resins through a die of a specified length and diameter under prescribed conditions of temperature, load, and piston position in the barrel as the timed measurement is being made.
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2004. Published April 2004. 9 p. This specification provides for the identification of polyethylene plastics extrusion materials for wire and cable in such a manner that the seller and the purchaser can agree on the acceptability of different commercial lots or shipments. The tests involved in...
Aмериканское Общество по Испытаниям и Материалам (ASTM). Текущее издание было утверждено 1 мая 2007. Опубликовано в июне 2007 года. Первоначально утверждено в 1953. Предпоследнее издание было утверждено в 2002 как D 1267 – 02. 4 стр. Данная методика предназначена для определения избыточного давления сжиженных нефтяных газов при температуре 37.8оС (100оF) до температуры анализа...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. Published June 2007. Originally approved in 1953. Last previous edition approved in 2002 as D 1267 – 02. 5 p. This test method covers the determination of the gage vapor pressures of liquefied petroleum gas products at temperatures of 37.8°C (100°F) up to and including a test temperature of...
Current edition approved Sept. 1, 2015. Published December 2015. Originally approved in 1953. Last previous edition approved in 2011 as D1278 – 91a (2011). — 6 p. These test methods cover the sampling and chemical analysis of solid natural rubber in the forms supplied to the rubber industry. The analytical procedures appear in the following order: Sampling Volatile Matter Dirt Ash...
6 с.
Язык: английский.
Стандартный метод определения плотности, относительной плотности (удельного веса) или плотности в градусах API сырой нефти и жидких нефтепродуктов ареометром
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2013. Published July 2013. Originally approved in 1954. Last previous edition approved in 2007 as D1308 – 02 (2007). 2 p. This test method covers determination of the effect of household chemicals on clear and pigmented organic finishes, resulting in any objectionable alteration in the surface,...
American Society for Testing and Materials (ASTM). Current edition approved May 10, 2002. Published July 2002. 3 p. This test method covers determination of the effect of household chemicals on clear and pigmented organic finishes, resulting in any objectionable alteration in the surface, such as discoloration, change in gloss, blistering, softening, swelling, loss of adhesion,...
Current edition approved Nov. 1, 2016. Published November 2016. Originally approved in 1954. Last previous edition approved in 2008 as D1329 – 08. — 5 p. This test method describes a temperature-retraction procedure for rapid evaluation of crystallization effects and for comparing viscoelastic properties of rubber and rubber-like materials at low temperatures. This test method is...
Current edition approved June 1, 2015. Published September 2015. Originally approved in 1954. Last previous edition approved in 2010 as D1330 – 04 (2010). — 3 p. This specification covers gaskets cut from sheet rubber that are intended for general gasket applications on water, air, and low-pressure steam. They are not intended for use with oils and strong acids.
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2007. Published August 2007. Originally approved in 1954. Last previous edition approved in 2005 as D 1349 – 99 (2005). This practice covers a list of standard temperatures from which selection may be made for any specific test or test method. Any standard or specification that specifies test...
Current edition approved July 1, 2014. Published August 2014. Originally approved in 1954. Last previous edition approved in 2009 as D1349 – 09. — 2 p. Reliable comparisons between different rubber compounds and between different laboratories is an essential component of effective testing. It is necessary to standardize the temperature and humidity conditions to which materials...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2007. Published December 2007. 3 p. This test method covers the float test for bituminous materials. The float test characterizes the flow behavior or consistency of certain bituminous materials. This test method is useful in determining the consistency of bitumen as one element in establishing...
Current edition approved July 1, 2015. Published September 2015. Originally approved in 1956. Last previous edition approved in 2013 as D1414 – 94 (2013). — 11 p. These test methods describe the procedures for determining the physical properties of O-rings and changes in these properties due to aging.
Current edition approved Jan. 1, 2012. Published March 2012. Originally approved in 1956. Last previous edition approved in 2006 as D1415 – 06. — 7 p. This test method covers a procedure for measuring the hardness of vulcanized or thermoplastic rubber. The hardness is obtained by the difference in penetration depth of a specified dimension ball under two conditions of contact with...
Current edition approved June 1, 2016. Published June 2016. Originally approved in 1956. Last previous edition approved in 2010 as D1417 – 10. — 11 p. These test methods cover test procedures for synthetic rubber latices ABR, BR, CR, IIR, IR, NBR, NCR, NIR, PBR, PSBR, SBR, SCR, SIR, synthetic rubber latices having substitute carboxylic acid (COOH) groups on the polymer chain (X),...
Current edition approved Jan. 1, 2017. Published January 2017. Originally approved in 1956. Last previous edition approved in 2016 as D1418 – 10a (2016). — 3 p. This practice covers a system of general classification for the basic rubbers both in dry and latex forms determined from the chemical composition of the polymer chain. The purpose of this practice is to provide a...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2009. Published October 2009. 31 p. These test methods cover the determination of various strength and related properties of wood by testing small clear specimens. These test methods represent procedures for evaluating the different mechanical and physical properties, controlling factors such...
Current edition approved Nov. 1, 2014. Published December 2014. Originally approved in 1957. Last previous edition approved in 2010 as D1456 – 86 (2010). — 5 p. This test method covers determination of the elongation of soft vulcanized rubber compounds under a specified stress.
Current edition approved Nov. 1, 2014. Published December 2014. Originally approved in 1957. Last previous edition approved in 2010 as D1460 – 86 (2010). — 3 p. This test method covers a technique to measure the effect of immersion liquids on rubber vulcanizates or rubbery materials. Change in specimen geometry and dimensions are observed through the transparent walls of the tube...
Current edition approved Aug. 1, 2015. Published October 2015. Originally approved in 1957. Last previous edition approved in 2011 as D1485 – 07 (2011). — 3 p. This practice, intended for referee purposes, covers a uniform procedure for sampling lots of solid natural rubber. Natural rubber generally is marketed in bales or packages of various sizes. A procedure for determining the...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2007. Published April 2007. Originally approved in 1957. Last previous edition approved in 2002 as D 1485 – 86 (2002). This practice, intended for referee purposes, covers a uniform procedure for sampling lots of solid natural rubber.
Current edition approved June 1, 2015. Published July 2015. Originally approved in 1957. Last previous edition approved in 2013 as D1506 – 99 (2013). — 4 p. These test methods cover the determination of the ash content of carbon black.
Current edition approved June 1, 2012. Published August 2012. Originally approved in 1957. Last previous edition approved in 2007 as D1508 – 02 (2007)ε1. — 3 p. This test method covers the determination of the fines and attrition of pelleted carbon black.
Current edition approved Nov. 1, 2015. Published December 2015. Originally approved in 1957. Last previous edition approved in 2012 as D1509 – 95 (2012). — 3 p. These test methods cover the determination of the heating loss of carbon black at 125°C. This heating loss consists primarily of moisture, but other volatile materials may also be lost. These test methods are not...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 15, 2008. Published February 2008. Originally approved in 1957. Last previous edition approved in 2007 as D 1510 – 07a. This test method covers the determination of the iodine adsorption number of carbon black.
Current edition approved Nov. 1, 2016. Published November 2016. Originally approved in 1957. Last previous edition approved in 2016 as D1510 – 16. — 10 p. This test method covers the determination of the iodine adsorption number of carbon black. Method A is the original test method for this determination and Method B is an alternate test method using automated sample processing...
Current edition approved June 1, 2012. Published August 2012. Originally approved in 1957. Last previous edition approved in 2010 as D1511 – 10. — 4 p. This test method covers the determination of the pellet size distribution of carbon black.
Current edition approved Dec. 1, 2015. Published February 2016. Originally approved in 1975. Last previous edition approved in 2015 as D1512 – 15a. — 4 p. These test methods, Test Method A—Boiling Slurry and Test Method B—Sonic Slurry, are used to indicate the pH of the carbon black surface by measuring the pH of water in contact with the carbon black. The pH of the carbon black...
Current edition approved June 1, 2012. Published November 2012. Originally approved in 1957. Last previous edition approved in 2005 as D1513 – 05ε2. — 3 p. This test method covers the determination of the pour density of pelleted carbon blacks.
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2004. Published July 2004. Originally approved in 1957. Last previous edition approved in 2001 as D 1514 – 01. This test method covers the determination of the water wash sieve residue in regular untreated carbon blacks. It may not be applicable to oil-treated carbon blacks because the oil would...
Current edition approved June 15, 2015. Published August 2015. Originally approved in 1957. Last previous edition approved in 2011 as D1514 – 04 (2011). — 3 p. This test method covers the determination of the water wash sieve residue in regular untreated carbon blacks. It may not be applicable to oil-treated carbon blacks because the oil would prevent proper wetting of the black...
Current edition approved Aug. 1, 2014. Published November 2014. Originally approved in 1995. Last previous edition approved in 2009 as D1519 – 95 (2009)ε1. — 4 p. These test methods cover the determination of the melting range of commercial rubber processing chemicals either by use of capillary melting point tubes or by differential scanning calorimetry (DSC).
American Society for Testing and Materials (ASTM). Current edition approved March 10, 2000. Published May 2000. 8 p. This test method covers determination of the temperature at which a specified needle penetration occurs when specimens are subjected to specified controlled test conditions. This test method is not recommended for ethyl cellulose, nonrigid poly(vinyl chloride),...
ASTM, 2018. — 3 p. This test method covers the measurement of the color of transparent liquids by means of comparison with arbitrarily numbered glass standards. Users of this method should have normal color vision. The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 15, 2007. Published October 2007. 7 p. This test method may be used to determine the in-place density and unit weight of soils using a sand cone apparatus. This test method is applicable for soils without appreciable amounts of rock or coarse materials in excess of 11⁄2 in. (38 mm) in diameter.
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2009. Published October 2009. 14 p. These test methods cover laboratory compaction methods used to determine the relationship between molding water content and dry unit weight of soils (compaction curve) compacted in a 4- or 6-in. (101.6- or 152.4-mm) diameter mold with a 10.00-lbf. (44.48-N)...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2012. Published June 2012. 14 p. These test methods cover laboratory compaction methods used to determine the relationship between molding water content and dry unit weight of soils (compaction curve) compacted in a 4- or 6-in. (101.6- or 152.4-mm) diameter mold with a 10.00-lbf. (44.48-N) rammer...
Current edition approved Nov. 1, 2015. Published December 2015. Originally approved in 1957. Last previous edition approved in 2014 as D1566 – 14. — 17 p. This terminology covers definitions of technical terms used in the rubber industry. Terms that are generally understood or adequately defined in other readily available sources are not included. Definitions for terms that have...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2016. Published July 2016. Originally approved in 1911. Last previous edition approved in 2014 as D16 – 14. 10 p. This standard consists of technical terms used in standards under the jurisdiction of ASTM Committee D01 (on Paint and Related Coatings, Materials, and Applications), and of...
Current edition approved Aug. 1, 2017. Published August 2017. Originally approved in 1965. Last previous edition approved in 2011 as D1618 – 99 (2011). — 3 p. This test method covers the measurement of the degree of toluene discoloration by carbon black extractables and is useful in controlling the reaction processes for production of carbon black. This test method may not be...
Current edition approved Sept. 1, 2016. Published October 2016. Originally approved in 1958. Last previous edition approved in 2016 as D1619 – 16. — 5 p. These test methods cover the determination of the sulfur content of carbon black. The following test methods are included: Test Method A High-Temperature Combustion With Infrared Absorption Detection Procedures Test Method B...
Current edition approved June 1, 2016. Published June 2016. Originally approved in 1961. Last previous edition approved in 2012 as D1630 – 06 (2012). — 5 p. This test method covers the determination of the resistance to abrasion of vulcanized rubber, or other rubber materials that are similar to the standard reference compound, used for the soles and heels of footwear. It is not...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2014. Published February 2015. Originally approved in 1959. Last previous edition approved in 2009 as D1640 – 03 (2009). 4 p. These test methods can be used to determine the various stages and rates of drying, curing, and film formation of organic coatings for comparing types of coatings,...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2007. Published November 2007. Originally approved in 1959. Last previous edition approved in 2006 as D 1646 – 06. These test methods cover procedures for measuring a property called Mooney viscosity. Mooney viscosity is defined as the shearing torque resisting rotation of a cylindrical metal disk...
Current edition approved Dec. 15, 2015. Published January 2016. Originally approved in 1959. Last previous edition approved in 2012 as D1646 – 07 (2012). — 12 p. These test methods cover procedures for measuring a property called Mooney viscosity. Mooney viscosity is defined as the shearing torque resisting rotation of a cylindrical metal disk (or rotor) embedded in rubber within...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published April 2005. Originally approved in 1959. Last previous edition approved in 2000 as D 1654 – 92 (2000). 4 p. This test method covers the treatment of previously painted or coated specimens for accelerated and atmospheric exposure tests and their subsequent evaluation in respect to...
American Society for Testing and Materials (ASTM). Current edition approved March 10, 2003. Published April 2003. 9 p. These test methods cover the determination of the energy that causes plastic film to fail under specified conditions of impact of a free-falling dart. This energy is expressed in terms of the weight (mass) of the missile falling from a specified height which would...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2003. Published December 2003. Originally approved in 1960. Last previous edition approved in 1996 as D 1729 – 96. 4 p. This practice specifies the equipment and procedures for visual appraisal of the colors and color differences of opaque materials that are diffusely illuminated. These...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2009. Published July 2009. 6 p. This test method covers the determination of the effects of heat and air on a film of semisolid asphaltic materials. The effects of this treatment are determined from measurements of selected asphalt properties before and after the test.
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2006. Published August 2006. Originally approved in 1965. Last previous edition approved in 2005 as D 1765 – 05ae1. This classification system covers the classification of rubber-grade carbon blacks by the use of a four-character nomenclature system. The first character gives some indication of the...
Current edition approved May 1, 2017. Published May 2017. Originally approved in 1965. Last previous edition approved in 2016 as D1765 – 16. — 4 p. This classification system covers the classification of rubber-grade carbon blacks by the use of a four-character nomenclature system. The first character gives some indication of the influence of the carbon black on the rate of cure...
Current edition approved June 1, 2016. Published June 2016. Originally approved in 1960. Last previous edition approved in 2011 as D1766 – 05 (2011). — 2 p. This test method covers a practical test for the solubility of commercial chemicals used in rubber products. It is not a true measure of solubility, since equilibrium is not approached from both sides, that is, higher...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2012. Published May 2012. Originally approved in 1960. Last previous edition approved in 2006 as D 1785 – 06. 11 p. This specification covers poly(vinyl chloride) (PVC) pipe made in Schedule 40, 80, and 120 sizes and pressure-rated for water (see Appendix X1). Included are criteria for classifying...
American Society for Testing and Materials (ASTM). Current edition approved April l, 2008. Published May 2008. Originally approved in 1960. Last previous edition approved in 2002 as D l7l0 - 02. 5 p. This specification covers extruded polytetrafluoroethylene (PTFE) rod, heavy-walled tubing, and basic shapes manufactured from the PTFE resin of Specification D 4894 and reprocessed...
Current edition approved June 1, 2014. Published November 2014. Originally approved in 1960. Last previous edition approved in 2008 as D1799 – 03a (2008). — 3 p. This practice covers the sampling of packaged carbon blacks for shipment in bags, cartons, flexible intermediate bulk containers (FIBC), or other non-bulk packages. The tests to be made on the samples obtained by this...
Current edition approved June 1, 2016. Published June 2016. Originally approved in 1961. Last previous edition approved in 2011 as D1817 – 05 (2011). — 3 p. This test method covers the determination of the density of solid chemicals used as rubber additives during processing and manufacture. It is intended for determining the density of the rubber chemical itself and not for the...
Current edition approved June 1, 2015. Published August 2015. Originally approved in 1961. Last previous edition approved in 2010 as D1869 – 95 (2010). — 3 p. This specification covers rubber rings used to seal the joints of asbestos-cement pipe conforming to Specifications C296, C428, C668, and non-asbestos fiber-cement pipe conforming to Specification C1449. A specification is...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2007. Published December 2007. 9 p. This test method covers the determination of the CBR (California Bearing Ratio) of pavement subgrade, subbase, and base course materials from laboratory compacted specimens. The test method is primarily intended for (but not limited to) evaluating the strength...
Current edition approved Nov. 1, 2015. Published December 2015. Originally approved in 1961. Last previous edition approved in 2011 as D1900 – 06(2011). — 2 p. This practice covers procedures for the sampling and data reporting of bulk shipments of carbon black in threecompartment hopper rail cars and compartmented bulk hopper trailers.
Current edition approved May 1, 2012. Published May 2012. Originally approved in 1962. Last previous edition approved in 2007 as D1917 – 03 (2007). — 4 p. These test methods cover the determination of mill shrinkage of hot-polymerized styrene-butadiene rubbers (SBR) and their compounds.
Current edition approved June 1, 2013. Published July 2013. Originally approved in 1962. Last previous edition approved in 2012 as D1937 – 12. — 3 p. This test method covers the determination of the mass strength of pelleted carbon black. It is designed to determine the force required to pack a cylindrical column with pelleted carbon black. The results of this test are believed to...
Current edition approved June 1, 2015. Published July 2015. Originally approved in 1991. Last previous edition approved in 2010 as D1991 – 05 (2010). — 3 p. This test method covers a procedure for the assay of 2-mercaptobenzothiazole (MBT). It is based on a potentiometric titration of MBT with sodium hydroxide.
Current edition approved June 1, 2017. Published June 2017. Originally approved in 1991. Last previous edition approved in 2013 as D1992 – 91 (2013). — 2 p. This guide covers test methods for synthetic plasticizers that are used in rubber applications.
Current edition approved Nov. 1, 2013. Published January 2014. Originally approved in 1991. Last previous edition approved in 2008 as D1993 – 03 (2008). — 3 p. This test method covers a procedure which is used to measure the surface area of precipitated hydrated silicas by the conventional Brunauer, Emmett, and Teller (BET)2 theory ofmultilayer gas adsorption behavior using...
Current edition approved May 1, 2017. Published July 2017. Originally approved in 1962. Last previous edition approved in 2012 as D2000 – 12. — 53 p. This classification system covers the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2009. Published June 2009. 3 p. This test method covers the determination of the degree of solubility in trichloroethylene of asphalt materials having little or no mineral matter. This test method is a measure of the solubility of asphalt in trichloroethylene. The portion that is soluble in...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2007. Published July 2007. Originally approved in 1971. Last previous edition approved in 2006 as D 2084 – 06. This test method covers the use of the oscillating disk cure meter for determining selected vulcanization characteristics of vulcanizable rubber compounds.
Current edition approved Nov. 1, 2016. Published December 2016. Originally approved in 1971. Last previous edition approved in 2011 as D2084 – 11. — 12 p. This test method covers the use of the oscillating disk cure meter for determining selected vulcanization characteristics of vulcanizable rubber compounds. ISO 3417 is very similar to this test method. It has minor technical...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published July 2005. Originally approved in 1924. Last previous edition approved in 1999 as D 210 – 81a (1999). 2 p. This specification covers the pigment commercially known as bone black, ivory black, or drop black. The pigment may be purchased in the dry form or as an aqueous dispersion....
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2004. Published April 2004. 3 p. This practice lists procedures for determining the relative thermal stability of sheet or molded poly(vinyl chloride) compounds as indicated by discoloration due to exposure to an elevated temperature at controlled oven conditions.
Current edition approved Dec. 1, 2012. Published February 2013. Originally approved in 1962. Last previous edition approved in 2007 as D2136 – 02 (2007). — 3 p. Fabrics coated with rubber or rubber-like materials display increased stiffening when exposed to decreasing ambient temperatures. This test method describes a simple pass/ fail procedure whereby material flexibility at a...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published October 2005. Originally approved in 1962. Last previous edition approved in 2000 as D 2137–94(2000). These test methods cover the determination of the lowest temperature at which rubber vulcanizates and rubbercoated fabrics will not exhibit fractures or coating cracks when...
Current edition approved May 1, 2011. Published July 2011. Originally approved in 1962. Last previous edition approved in 2010 as D2137 – 10. — 7 p. These test methods cover the determination of the lowest temperature at which rubber vulcanizates and rubbercoatedfabrics will not exhibit fractures or coating cracks when subjected to specified impact conditions.
American Society for Testing and Materials (ASTM). Current edition approved July 15, 2006. Published January 2007. 6 p. This test method covers the determination of the unconfined compressive strength of cohesive soil in the intact, remolded, or reconstituted condition, using strain-controlled application of the axial load. This test method provides an approximate value of the...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2010. Published August 2010. 10 p. This test method covers procedures for the determination of kinematic viscosity of liquid asphalts (bitumens), road oils and distillation residues of liquid asphalts (bitumens) all at 60°C [140°F] and of asphalt cements at 135°C [275°F in the range from 6 to 100...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 1963. Last previous edition approved in 1999 as D 2196 – 99. 5 p. These test methods cover the determination of the apparent viscosity and the shear thinning and thixotropic properties of non-Newtonian materials in the shear rate range from 0.1 to...
Current edition approved May 1, 2012. Published May 2012. Originally approved in 1963. Last previous edition approved in 2007 as D2226 – 93 (2007). — 2 p. This classification is intended to establish classification and test methods for certain types of oil used in extending andprocessing styrene-butadiene rubbers (SBR) and butadiene rubbers (BR). Its purpose is for...
Current edition approved Sept. 1, 2015. Published December 2015. Originally approved in 1963. Last previous edition approved in 2011 as D2227 – 96 (2011). — 2 p. This specification covers minimum physical and chemical quality requirements or specifications for five grades of raw natural rubber.
Current edition approved July 1, 2009. Published September 2009. Originally approved in 1963. Last previous edition approved in 2004 as D2228 – 04ε1. — 9 p. This test method covers the determination of the abrasion resistance of vulcanized (thermoset) rubbers, thermoplastic elastomers, and elastomeric and similar materials to a standardized reference system. A standardized set of...
Current edition approved May 1, 2012. Published May 2012. Originally approved in 1963. Last previous edition approved in 2007 as D2230 – 96 (2007). — 5 p. This test method covers the determination of the extrudability of unvulcanized SBR and NBR rubber compounds through a screw-type extruder equipped with ASTM Extrusion Die, Garvey type. This test method is designed to allow the...
Current edition approved Aug. 1, 2015. Published January 2016. Originally approved in 1964. Last previous edition approved in 2010 as D2240 – 05 (2010). — 13 p. This test method covers twelve types of rubber hardness measurement devices known as durometers: Types A, B, C, D, DO, E, M, O, OO, OOO, OOO-S, and R. The procedure for determining indentation hardness of substances...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published November 2005. Originally approved in 1964. Last previous edition approved in 2002 as D 2244 – 02. 10 p. This practice covers the calculation, from instrumentally measured color coordinates based on daylight illumination, of color tolerances and small color differences between...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1964. Last previous edition approved in 1999 as D 2245 – 90 (1999). 4 p. This test method covers the identification of oils and oil acids in vehicles that have been separated from solvent-reducible paints. The test method is based on a gas...
American Society for Testing and Materials (ASTM). Current edition approved August 10, 2002. Published October 2002. Originally published as D 2272-
64. Last previous edition D 2272-98. 12 p. This test method2 utilizes an oxygen-pressured vessel to evaluate the oxidation stability of new and in-service turbine oils having the same composition (base stock and additives) in the...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1965. Last previous edition approved in 2001 as D 2337 – 01. 2 p. This test method covers the determination of the extent to which multicolor lacquers resist coagulation and coalescence when subjected to freezing and subsequent thawing. The...
This standard is issued under the fixed designation D2344/D2344M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1965. Last previous edition approved in 1999 as D 2350 – 90 (1999). 2 p. This test method covers the determination of the total antimony oxide in white pigment separated from solvent-reducible paints. The values stated in SI units are to be...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1965. Last previous edition approved in 1999 as D 2351 – 90 (1999). 3 p. This test method covers the determination of sulfide sulfur in white pigment separated from solvent-reducible paints. The values stated in SI units are to be regarded as...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1965. Last previous edition approved in 1999 as D 2352 – 85 (1999). 2 p. This test method covers the determination of sulfur dioxide in white pigment separated from solvent-reducible paints. This test method is not applicable in the presence...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1965. Last previous edition approved in 1999 as D 2371 – 85 (1999). 2 p. 1.1 This test method covers the procedure for the quantitative separation of the vehicle from the pigment in solvent-reducible coatings. This test method has been proven...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1965. Last previous edition approved in 1999 as D 2372 – 85 (1999). 2 p. This practice covers the procedure for the separation of the vehicle from the pigment in solvent-reducible paint. In the development of the practice the following...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1965. Last previous edition approved in 1999 as D 2373 – 85 (1999). 3 p. This test method covers a titrimetric determination of cobalt in liquid paint driers that can be dissolved in glacial acetic acid and utilizes the disodium salt of...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1965. Last previous approved in 1999 as edition D 2374 – 85 (1999). 3 p. This test method covers a titrimetric determination of lead in liquid paint driers that can be dissolved in glacial acetic acid and utilizes the disodium salt of...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1965. Last previous edition approved in 1999 as D 2375 – 85 (1999). 3 p. This test method covers a titrimetric determination of manganese in liquid paint driers that can be dissolved in a toluene-alcohol mixture and utilizes the disodium salt...
American Society for Testing and Materials (ASTM). Current edition approved July 15, 2008. Published July 2008. Originally approved in 1965. Last previous edition approved in 2002 as D 2412 – 02. 6 p. This test method covers the determination of load-deflection characteristics of plastic pipe under parallel-plate loading. This test method covers thermoplastic resin pipe,...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2008. Published February 2008. Originally approved in 1965. Last previous edition approved in 2006 as D 2414 – 06ae1. This test method covers the determination of the oil absorption number of carbon black.
Current edition approved Jan. 1, 2016. Published January 2016. Originally approved in 1965. Last previous edition approved in 2014 as D2414 – 14. — 8 p. This test method covers the determination of the oil absorption number of carbon black.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2009. Published July 2009. 9 p. This test method is intended to serve as a rapid fieldcorrelation test. The purpose of this test method is to indicate, under standard conditions, the relative proportions of clay-like or plastic fines and dust in granular soils and fine aggregates that pass the...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2006. Published March 2006. 6 p. This test method covers the determination of the coefficient of permeability by a constant-head method for the laminar flow of water through granular soils. The procedure is to establish representative values of the coefficient of permeability of granular soils that...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2004. Published November 2004. 10 p. These test methods covers procedures for determining the magnitude and rate of consolidation of soil when it is restrained laterally and drained axially while subjected to incrementally applied controlled-stress loading.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2009. Published July 2009. 8 p. These test methods and practices, given under the headings titled Composition, Consistency, Stability, and Examination of Residue, cover the examination of asphalt emulsions composed principally of a semisolid or liquid asphaltic base, water, and an emulsifying agent.
Current edition approved Sept. 1, 2015. Published December 2015. Originally approved in 1965. Last previous edition approved in 2011 as D2449 – 88 (2011). — 2 p. This specification covers bale coating on bales of natural rubber (that have rubber wrapper sheets on the bales) and includes test method description. It specifies the maximum permissible amount of such coating. This...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2006. Published March 2006. Originally approved in 1926. Last previous edition approved in 2002 as D 245 – 00 (2002). 16 p. This practice covers the basic principles for establishing related unit stresses and stiffness values for design with visually-graded solid sawn structural lumber. This...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2012. Published April 2012. Originally approved in 1966. Last previous edition approved in 2006 as D2484 – 06. 3 p. This specification covers electrical insulating tape consisting of a polyester plastic film coated on one side with a pressure-sensitive adhesive. The values stated in SI units...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2012. Published February 2012. Originally approved in 1966. Last previous edition approved in 2006 as D2486 – 06. 4 p. These test methods cover a procedure for determining the resistance of wall paints to erosion caused by scrubbing, referred to herein after as scrub resistance. Two test methods...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2006. Published June 2006. 12 p. This practice describes a system for classifying mineral and organo-mineral soils for engineering purposes based on laboratory determination of particle-size characteristics, liquid limit, and plasticity index and shall be used when precise classification is required.
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2009. Published January 2010. Originally approved in 1966. Last previous edition approved in 2009 as D2513 – 09. 61 p. This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and rapid crack resistance of...
Current edition approved May 1, 2017. Published July 2017. Originally approved in 1966. Last previous edition approved in 2011 as D2527 – 83 (2011). — 2 p. This specification covers the strength and appearance of the splice in vulcanized rubber-seal material of any size, type,or cross-sectional shape. Many types and varieties of seals are used in services of all degrees of...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2004. Published June 2004. 20 p. These test methods cover the determination of the resistance of plastics to standardized (see Note 1) pendulumtype hammers, mounted in standardized machines, in breaking standard specimens with one pendulum swing (see Note 2). The standard tests for these test...
This standard is issued under the fixed designation D2562; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard is issued under the fixed designation D2563; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2012. Published December 2012. Originally approved in 1966. Last previous edition approved in 2009 as D2564 – 04(2009). 5 p. This specifcation covers requirements for poly(vinyl chloride) (PVC) solvent cements to be used in joining poly(vinyl chloride) piping systems. These solvent cements are...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2007. Published June 2007. Originally approved in 1925. Last previous edition approved in 2005 as D257 – 99(2005). 18 p. These test methods cover direct-current procedures for the measurement of dc insulation resistance, volume resistance, and surface resistance. From such measurements and the...
American Society for Testing and Materials (ASTM). Current edition approved February 1, 2004. Published March 2004. 4 p. This test method covers the measurement of the wetting tension of a polyethylene or polypropylene film surface in contact with drops of specific test solutions in the presence of air.
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 1967. Last previous edition approved in 2000 as D 2621 – 87 (2000). 26 p. This test method covers the qualitative characterization or identification of separated paint vehicle solids by infrared spectroscopy within the limitations of infrared...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1927. Last previous edition approved in 1999 as D 263 – 75 (1999). 2 p. This specification covers the dry pigment commercially known as chrome oxide green. The values stated in SI units are to be regarded as the standard. The values given in...
Current edition approved Aug. 1, 2015. Published January 2016. Originally approved in 1967. Last previous edition approved in 2014 as D2632 – 14. — 5 p. This test method covers the determination of impact resilience of solid rubber from measurement of the vertical rebound of a dropped mass. This test method is not applicable to the testing of cellular rubbers or coated fabrics.
Current edition approved Jan. 1, 2014. Published February 2014. Originally approved in 1967. Last previous edition approved in 2008 as D2663 – 08. — 12 p. These test methods cover the degree of dispersion of carbon black in rubber. Four test methods are described as follows: Test Method A—Visual Inspection Test Method B—Agglomerate Count Test Method C—Microroughness Measurement...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published January 2005. 7 р. This test method covers the determination of the corrosivity of water by evaluating pitting and by measuring the weight loss of metal specimens. Pitting is a form of localized corrosion: weight loss is a measure of the average corrosion rate. The rate of corrosion...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1965. Last previous edition approved in 1999 as D 2698 – 90 (1999). 2 p. This test method covers the separation of pigment from solvent-reducible paints and the calculation of the percent pigment from the results of nonvolatile determinations on...
Current edition approved June 1, 2016. Published June 2016. Originally approved in 1968. Last previous edition approved in 2011 as D2702 – 05 (2011). — 4 p. This practice covers a simple, rapid practice to prove the identity of a rubber chemical before incorporation into a rubber mix by comparison of its infrared absorption spectrum with that of a reference specimen. This...
Standard Test Method for Bromine Index of Petroleum Hydrocarbons by Electrometric Titration ASTM International, 2015. — Официальный перевод выполнен: ФБУ «КВФ «ИНТЕРСТАНДАРТ», Москва 2015. — 14 страниц. Этот метод испытаний охватывает определение количества бром-реактивного материала в нефтяных углеводородах и, таким образом, является мерой следовых количеств ненасыщенных...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2011. Published February 2011. Originally approved in 1968. Last previous edition approved in 2003 as D 2729 – 03. 5 p. This specification covers requirements and test methods for materials, dimensions, workmanship, chemical resistance, and joint tightness of poly (vinyl chloride) (PVC) sewer and...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1969. Last previous edition approved in 1999 as D 2793 – 99. 3 p. This test method covers the determination of the block resistance of organic coatings on wood and wood-based panel substrates. Block resistance is the ability of a coating to resist...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2010. Published December 2010. Originally approved in 1969. Last previous edition approved in 2004 as D2794 – 93 (2004). 3 p. This test method covers a procedure for rapidly deforming by impact a coating film and its substrate and for evaluating the effect of such deformation. This test method...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1969. Last previous edition approved in 1999 as D 2832 – 85 (1999). 3 p. This guide is intended to aid in the selection of the proper ASTM standard for determining the volatile and nonvolatile content of paint and related coatings.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2006. Published November 2006. 10 p. This test method covers the determination of the water absorption of rigid cellular plastics by measuring the change in buoyant force resulting from immersion under a 5.1 cm (2-in.) head of water for the specified immersion period of 96 h. This test method...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 15, 2007. Published October 2007. 6 p. This test method covers determination of the strength and stress-strain relationships of a cylindrical specimen of either undisturbed or remolded cohesive soil. Specimens are subjected to a confining fluid pressure in a triaxial chamber. No drainage of the...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1970. Last previous edition approved in 1998 as D 2921 – 98. 2 p. This test method covers simple qualitative field or laboratory tests to determine water repellency or the presence of chlorinated phenol2 preservative chemicals in wood products that...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2009. Published August 2009. 3 p. This specification covers quality-controlled graded aggregates that, when hauled to and properly spread and compacted on a prepared grade to appropriate density standards, may be expected to provide adequate stability and load support for use as highway or airport...
Current edition approved July 1, 2015. Published August 2015. Originally approved in 1928. Last previous edition approved in 2013 as D297 – 13. — 37 p. These test methods cover the qualitative and quantitative analysis of the composition of rubber products of the “R” family (see 3.1). Many of these test methods may be applied to the analysis of natural and synthetic crude...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 15, 2006. Published November 2006 Originally approved in 1971. Last previous edition approved in 2001 as D2992-01. 11 p. This practice establishes two procedures, Procedure A (cyclic) and Procedure B (static), for obtaining a hydrostatic design basis (HDB) or a pressure design basis (PDB) for...
American Society for Testing and Materials (ASTM). Current edition approved February 1, 2004. Published March 2004. 4 p. This is a fire-test-response standard. This test method covers a small-scale laboratory screening procedure for comparing relative extent and time of burning and loss of mass of rigid thermoset cellular plastics. This test method is to be used solely to...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2005. Published February 2005. Originally approved in 1972. Last previous edition approved in 1996 as D 3022 – 84 (1996). 4 p. This test method covers the determination, through the use of a miniature sandmill, of the color and strength of dry color pigments. The values stated in SI units are to...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2008. Published May 2008. Originally approved in 1972. Last previous edition approved in 2008 as D 3053 – 08. This terminology covers a compilation of definitions of technical terms used in the carbon black and rubber industries. Terms that are generally understood or adequately defined in other...
Current edition approved Dec. 15, 2015. Published January 2016. Originally approved in 1972. Last previous edition approved in 2013 as D3053 – 13a. — 4 p. This terminology covers a compilation of definitions of technical terms used in the carbon black and rubber industries. Terms that are generally understood or adequately defined in other readily available sources are not...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2004. Published December 20043. 7 p. This test method covers the determination of the consolidated drained shear strength of a soil material in direct shear. The test is performed by deforming a specimen at a controlled strain rate on or near a single shear plane determined by the configuration of...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1972. Last previous edition approved in 2001 as D 3133 – 01. 3 p. This test method covers the quantitative determination of the content of cellulose nitrate (also known as nitrocellulose) in lacquers containing alkyd resins. The values stated in...
Current edition approved Nov. 1, 2013. Published December 2013. Originally approved in 1972. Last previous edition approved in 2007 as D3137 – 81 (2007). — 3 p. This test method covers the determination of the ability of rubber to withstand the environmental effects of high humidity. This is accomplished by examination of the material after removal from the moisture-laden...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2008. Published July 2008. 6 p. This test method covers the determination of flash points by the Tag Open-Cup Apparatus of cutback asphalts having flash points of less than 93°C (200°F).
Current edition approved June 1, 2016. Published June 2016. Originally approved in 1973. Last previous edition approved in 2011 as D3156 – 96 (2011). — 5 p. This practice covers the detection and identification by thin-layer chromatography of antidegradants (antioxidants, antiozonants, and stabilizers) that may be present in raw rubber or rubber products. Analysis for other types...
Current edition approved Aug. 1, 2015. Published September 2015. Originally approved in 1973. Last previous edition approved in 2010 as D3157 – 05 (2010)ɛ1. — 3 p. This test method covers a method of classifying the color of raw rubber according to a standard color scale.
American Society for Testing and Materials (ASTM). Current edition approved February 1, 2004. Published March 2004. 5 p. This specification covers melt processible molding and extrusion materials of modified ETFE-fluoropolymer. The ETFE resin is a copolymer of ethylene containing approximately 75 mass % of tetrafluoroethylene.
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1973. Last previous edition approved in 1999 as D 3168 – 85 (1999). 5 p. This practice describes a procedure for the qualitative identification in emulsion paints of most types of polymers present as major components of the paint vehicle....
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. Published June 2007. Originally approved in 1973. Last previous edition approved in 2006 as D 3182 – 89 (2006). This practice provides a listing of reference compounding materials required to prepare the rubber test compounds listed in succeeding methods and contains procedures for weighing....
Current edition approved Jan. 1, 2016. Published January 2016. Originally approved in 1973. Last previous edition approved in 2015 as D3182 – 15a. — 8 p. This practice provides a listing of reference compounding materials required to prepare the rubber test compounds listed in succeeding methods and contains procedures for weighing. It also specifies the mixing equipment, general...
Current edition approved Nov. 1, 2015. Published December 2015. Originally approved in 1973. Last previous edition approved in 2010 as D3183 – 10. — 2 p. This practice covers methods for the preparation of pieces of a rubber vulcanizate that is not in the form of sheet. Such pieces are used as a source from which specimens are obtained for testing.
This practice covers methods for the preparation of pieces of a rubber vulcanizate that is not in the form of sheet. Such pieces are used as a source from which specimens are obtained for testing. This practice is under the jurisdiction of ASTM Committee D11 on Rubber and is the direct responsibility of Subcommittee D11.10 on Physical Testing. Current edition approved May 1, 2007....
Current edition approved May 1, 2011. Published July 2011. Originally approved in 1973. Last previous edition approved in 2007 as D3184 – 07. — 3 p. This practice covers the standard materials, test formulas, mixing procedures, and test methods for the evaluation and production control of natural rubber (NR).
Current edition approved June 1, 2016. Published July 2016. Originally approved in 1973. Last previous edition approved in 2010 as D3185 – 06 (2010). — 6 p. These test methods cover the standard materials, test formulas, mixing procedures, and test methods for the evaluation of emulsion polybutadiene (EBR) and styrene-butadiene rubbers (SBR) including the emulsion polybutadiene...
Current edition approved June 1, 2016. Published July 2016. Originally approved in 1981. Last previous edition approved in 2011 as D3186 – 07 (2011). — 4 p. These test methods cover the standard materials, test formula, mixing procedures, and test methods for the evaluation and production control of pigmented types of styrenebutadiene rubbers (SBR). This includes the pigmented SBR...
Current edition approved June 1, 2016. Published July 2016. Originally approved in 1973. Last previous edition approved in 2011 as D3187 – 06 (2011). — 5 p. These test methods cover the standard materials, test formulas, mixing procedures and test methods for the evaluation of various types of acrylonitrile-butadiene rubber (NBR).
Current edition approved Dec. 1, 2010. Published February 2011. Originally approved in 1973. Last previous edition approved in 2006 as D3188 – 06. — 5 p. These test methods cover the standard materials, test formula, mixing procedures, and test methods for the evaluation and production control of non-halogenated isobuteneisoprene rubbers (IIR), commonly known as butyl rubber.
Current edition approved June 1, 2016. Published July 2016. Originally approved in 1973. Last previous edition approved in 2011 as D3189 – 06 (2011). — 6 p. These test methods cover the standard materials, test formula, mixing procedures, and test methods for evaluation of butadiene rubber (BR) made by polymerization in solution.
Current edition approved November 1, 2004. Published November 2004. Originally approved in 1930. Last previous edition approved in 1999 as D 319 – 95 (1999). — 2 p. This specification covers synthetic amyl alcohol.
Current edition approved June 1, 2016. Published July 2016. Originally approved in 1973. Last previous edition approved in 2010 as D3190 – 06 (2010). — 6 p. This test method covers the standard materials, test formulas, mixing procedures and test methods for evaluation and quality control testing of chloroprene rubbers (CR). CR can be generally classified according to the two...
Current edition approved Sept. 1, 2014. Published November 2014. Originally approved in 1973. Last previous edition approved in 2010 as D3191 – 10. — 8 p. These test methods cover the standard materials, test formula, mixing procedure, and test methods for the evaluation and production control of carbon blacks in styrene butadiene rubber (SBR).
Current edition approved Sept. 1, 2014. Published November 2014. Originally approved in 1973. Last previous edition approved in 2009 as D3192 – 09. — 7 p. These test methods cover the standard materials, test formulation, mixing procedure, and test methods for the evaluation and production control of carbon blacks in natural rubber (NR).
Current edition approved Jan. 1, 2017. Published January 2017. Originally approved in 1973. Last previous edition approved in 2009 as D3194 – 04 (2009). — 3 p. This test method gives an indication of the oxidation resistance of raw natural rubber at a specified temperature. This resistance is indicated by the Plasticity Retention Index (PRI), a ratio expressed as a percentage of...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1982. Last previous edition approved in 2001 as D 3260 – 01. 2 p. This test method covers the evaluation of the mortar and acid resistance of clear protective coating factory applied to extruded aluminum substrates. The values stated in SI units...
Current edition approved May 1, 2017. Published May 2017. Originally approved in 1973. Last previous edition approved in 2015 as D3265 – 15a. — 6 p. This test method covers the determination of the tint strength of carbon black relative to an industry tint referenceblack (ITRB).
American Society for Testing and Materials (ASTM). Current edition approved April 10, 2003. Published June 2003. 6 p. This specification establishes requirements and methods of test for the material, dimensions, and workmanship, and the physical and electrical properties of molded sheet in minimum thicknesses of A.794 mm (t/tz in)l manufactured from PTFE resin molding materials.
American Society for Testing and Materials (ASTM). Current etiition approvecl April 1, 2006 Published Jtrne 2006. 4 р. This specilication covers skived tape in thicknesses from 0.013 to 6.35 mm (0.0005 to 0.250 in.) manufacturecl by skiving from PTFE resin molcling and extrusion materials
Current edition approved May 1, 2017. Published May 2017. Originally approved in 1974. Last previous edition approved in 2012 as D3314 – 02 (2012). — 4 p. This test method covers the determination of long polystyrene blocks in SBR rubbers and styrene-reinforced latices. Percent block styrene content may be determined in the range from 1 to 100 %. This test method is intended for...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1974. Last previous edition approved in 2001 as D 3322 – 82 (2001). 4 p. This practice covers the selection and use of procedures for testing primers and primer surfacers. The test methods included are listed in Table 1. The values stated in SI...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1974. Last previous edition approved in 1999 as D 3335 – 85a (1999). 4 p. This test method covers the determination of lead2 contents between 0.01 and 5 %, cadmium contents between 50 and 150 ppm (mg/kg), and cobalt contents between 50 and 2000...
Current edition approved May 1, 2012. Published June 2012. Originally approved in 1974. Last previous edition approved in 2007 as D3346 – 07. — 4 p. These test methods explain the use of the shearing disk viscometer to obtain an indication of the processability ofnon-pigmented emulsion styrene- butadiene rubbers (SBR). They may also be used to separate those polymers that are easy...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2009. Published June 2009. Originally approved in 1974. Last previous edition approved in 2008 as D3359 – 08. 8 p. These test methods cover procedures for assessing the adhesion of coating films to metallic substrates by applying and removing pressure-sensitive tape over cuts made in the film....
Американское общество материалов и контроля (ASTM). Июнь 2009. ЗАО «Технорматив», перевод на русский язык, 2009. 16 стр. Эти методики испытаний описывают процедуры для оценки адгезии пленочных покрытий к металлическим субстратам путем наложения и снятия чувствительной к давлению клейкой ленты на прорези, сделанные в этом покрытии
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2017. Published March 2017. Originally approved in 1974. Last previous edition approved in 2009 as D3359 – 09ɛ2. 9 p. These test methods cover procedures for assessing the adhesion of relatively ductile coating films to metallic substrates by applying and removing pressure-sensitive tape over...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2011. Published June 2011. Originally approved in 1974. Last previous edition approved in 2005 as D3363 – 05. 3 p. NOTES: Figure 1 was corrected editorially in August 2011. Figure 2 and Section 7 were corrected editorially in March 2012. This test method covers a procedure for rapid, inexpensive...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1974. Last previous edition D approved in 2000 as D 3363 – 00. 3 p. This test method covers a procedure for rapid, inexpensive determination of the film hardness of an organic coating on a substrate in terms of drawing leads or pencil leads...
American Society for Testing and Materials (ASTM). Current edition approved March 10, 1999. This test method is useful for quality-control tests on PVC compounds having a wide range of melt viscosities. Measurements are made at shear rates close to 1 s−1.
4 p.
Current edition approved April 15, 2016. Published November 2016. Originally approved in 1975. Last previous edition approved in 2015 as D3389 – 15. — 6 p. This test method covers the determination of the wear resistance of fabrics coated with rubber or plastics to abrasion. The abrasion is measured by mass loss or number of cycles required to wear through the coating to initially...
Current edition approved May 1, 2014. Published May 2014. Originally approved in 1975. Last previous edition approved in 2009 as D3393 – 91 (2009). — 2 p. This specification sets forth the minimum requirements for hydrostatic resistance of fabrics coated with rubber orplastics. Coated fabrics satisfying these requirements are considered to be waterproof.
Current edition approved June 1, 2016. Published July 2016. Originally approved in 1975. Last previous edition approved in 2011 as D3403 – 07 (2011). — 6 p. These test methods cover the standard materials, test formula, mixing procedures, and test methods for the evaluation and production control of isoprene rubber (IR).
Current edition approved May 1, 2017. Published May 2017. Originally approved in 1975. Last previous edition approved in 2012 as D3452 – 06 (2012). — 5 p. This practice covers the identification of polymers in raw rubbers, and cured and uncured compounds, based on a single polymer, by the gas chromatographic patterns of their pyrolysis products (pyrograms). Implementation of this...
Current edition approved June 1, 2016. Published July 2016. Originally approved in 1976. Last previous edition approved in 2010 as D3484 – 06 (2010). — 5 p. These test methods cover the standard materials, test formulas, mixing procedures, and test methods for the evaluation and production control of oil-extended polybutadiene rubber (OE-BR) polymerized in an appropriate solution.
Current edition approved July 1, 2016. Published August 2016. Originally approved in 1976. Last previous edition approved in 2015 as D3492 – 15. — 16 p. This specification covers the minimum requirements for individually packaged male condoms made from natural rubber latex and intended for single use. This specification does not cover the specifications for lubricants or other...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2007. Published August 2007. Originally approved in 1976. Last previous edition approved in 2006 as D 3493 – 06e1. This test method covers the procedure for the mechanical compression of a carbon black sample and the determination of the oil absorption number of the compressed sample.
Current edition approved Jan. 1, 2016. Published January 2016. Originally approved in 1976. Last previous edition approved in 2014 as D3493 – 14. — 4 p. This test method covers the procedure for the mechanical compression of a carbon black sample and the determination of the oil absorption number of the compressed sample.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 10, 1999. Published January 2000. Originally published as D 3514 –
76. Discontinued November 1995 and reinstated as D 3514 – 96. 5 p. This test method covers the determination of the resistance to the formation of pills and other surface distortions such as fuzzing of textile fabrics. The method...
Current edition approved July 1, 2014. Published November 2014. Originally approved in 1977. Last previous edition approved in 2009 as D3566 – 03 (2009). — 3 p. This practice covers the determination of bromine and chlorine in rubber. This procedure is applicable to raw or cured NR, SBR, BR, IR, IIR, CIIR, BIIR, and EPDM rubbers and blends of these. Iodine interferes, but...
Current edition approved Nov. 1, 2013. Published January 2014. Originally approved in 1977. Last previous edition approved in 2009 as D3568 – 03 (2009). — 5 p. These test methods specify the standard materials, test formulas, mixing procedures, and test methods for the evaluation and production control of ethylene propylene diene rubbers (EPDM).
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2011. Published January 2012. Originally approved in 1977. Last previous edition approved in 2008 as D3574 – 08. 29 p. These test methods apply to slab, bonded, and molded flexible cellular products known as urethane foams. Urethane foam is generally defined as an expanded cellular product produced...
Current edition approved Nov. 1, 2015. Published December 2015. Originally approved in 1977. Last previous edition approved in 2009 as D3577 – 09ε1. — 4 p. This specification covers certain requirements for packaged sterile rubber surgical gloves used in conducting surgical procedures.
Current edition approved Nov. 1, 2015. Published December 2015. Originally approved in 1977. Last previous edition approved in 2010 as D3578 – 05(2010). — 5 p. This specification covers certain requirements for natural rubber gloves used in conducting medical examinations and diagnostic and therapeutic procedures. It also covers natural rubber gloves used in handling contaminated...
Current edition approved June 1, 2016. Published July 2016. Originally approved in 1977. Last previous edition approved in 2010 as D3579 – 77 (2010). — 3 p. This specification covers Penrose-type rubber tubes used in performing certain surgical drainage procedures. The specification provides for packaged sterile rubber tubes and packaged or bulk nonsterile rubber tubes.
American Society for Testing and Materials (ASTM). Current edition approved Dec. 15, 2009. Published January 2010. 4 p. This test method covers the determination of the softening point of bitumen in the range from 30 to 157°C [86 to 315°F] using the ring-and-ball apparatus immersed in distilled water [30 to 80°C] or USP glycerin (above 80 to 157°C).
Current edition approved Aug. 1, 2014. Published November 2014. Originally approved in 1977. Last previous edition approved in 2009 as D3616 – 95 (2009). — 5 p. This test method covers the determination of the dilute solution viscosity (DSV), the gel characteristics, and the swelling index of raw non-oil-extended and non-pigmented SBR and NBR. This test method may be used to...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1977. Last previous edition approved in 1999 as D 3618 – 85a (1999). 3 p. This test method is intended as a screening test to determine if the solids in a paint contain more than 0.5 % lead. The test described barely detects the presence of 0.4...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1977. Last previous edition approved in 1999 as D 3624 – 85a (1999). 4 p. This test method covers the determination of the content of mercury in the range between 10 and 1000 ppm (mg/kg) present in liquid coatings, coatings vehicles, or in dried...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published August 2005. Originally approved in 1933. Last previous edition approved in 2001 as D 365 – 01. 4 p. This guide covers the testing of soluble nitrocellulose base solutions that are made by dispersing various kinds and concentrations of soluble nitrocellulose (cellulose nitrate) in...
Current edition approved July 1, 2016. Published July 2016. Originally approved in 1978. Last previous edition approved in 2010 as D3667 – 05 (2010). — 4 p. This specification covers the general requirements for materials used in rubber seals of flat-plate solar collectors, except vertically mounted passive collectors. Particular applications may necessitate other requirements...
Current edition approved June 1, 2015. Published September 2015. Originally approved in 1978. Last previous edition approved in 2010 as D3677 – 10ɛ1. — 21 p. These test methods cover rubber identification and are based on infrared examination of pyrolysis products (pyrolyzates) and films. These test methods are applicable to rubbers in the raw state and, when compounded, both in...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1978. Last previous edition approved in 1999 as D 3717 – 84 (1999). 3 p. This test method covers the determination of the content of antimony in the range between 50 and 200 ppm (mg/kg) present in the solids of liquid coatings or in dried films...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1978. Last previous edition approved in 1999 as D 3718 – 85a (1999). 4 p. This test method covers the determination of the content of chromium (including chromium oxide) in the range between 0.005 and 1.0 % present in the solids of liquid...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 1978. Last previous edition approved in 1999 as D 3720 - 90 (1999). 3 p. This test method covers the determination of the ratio of anatase to rutile in titanium dioxide pigments. The method is also applicable to pigment mixtures and pigmented...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1978. Last previous edition approved in 1999 as D 3721 – 83 (1999). 2 p. This specification covers synthetic red iron oxide for use in paints and coatings manufactured by any of the following: 1 Calcination of iron salts. 2 Precipitation...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1978. Last previous edition approved in 1999 as D 3722 – 82 (1999). 2 p. This specification covers dry and wet ground naturally occurring iron oxide, dry and wet ground calcined naturally occurring iron oxide, and mixtures of these with...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1978. Last previous edition approved in 1999 as D 3723 – 84 (1999). 2 p. This test method covers a procedure for the pigment content determination of water-based paints. It is applicable only to pigments that do not decompose or lose weight at...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1978. Last previous edition approved in 2001 as D 3732 – 82 (2001). 2 p. This practice applies to all coatings cured by ultraviolet energy. The values stated in SI units are to be regarded as standard. No other units of measurement are included...
Current edition approved July 1, 2016. Published July 2016. Originally approved in 1978. Last previous edition approved in 2010 as D3738 – 84 (2010). — 3 p. This specification covers rubber-coated cloth sheeting intended for use in the protection of mattresses on hospital beds.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2006. Published November 2006. Originally approved in 1979. Last previous edition approved 2004 as D 3754 – 04. 14 p. This specification covers machine-made fiberglass pipe, 8 in. (200 mm) through 156 in. (4000 mm), for use in pressure systems for conveying sanitary sewage, storm water, and many...
Current edition approved Nov. 1, 2014. Published December 2014. Originally approved in 1979. Last previous edition approved in 2008 as D3767 – 03 (2008). — 8 p. This practice is intended for use in determining the geometrical dimensions of rubber products and specimens for physical tests. This practice describes procedures for determining length, width, thickness, diameter, and...
Current edition approved June 1, 2015. Published August 2015. Originally approved in 1979. Last previous edition approved in 2007 as D3771 – 03 (2007). — 4 p. This specification covers the general requirements for materials used in rubber seals of concentrating solar collectors. Particular applications may necessitate other requirements that would take precedence over these...
Current edition approved July 15, 2015. Published September 2015. Originally approved in 1979. Last previous edition approved in 2010 as D3772 – 01 (2010). — 3 p. This specification covers the requirements for finger cots used in industrial applications which are made from natural rubber latex or a synthetic nitrile polymer. The purpose of this specification is to obtain...
Current edition approved Nov. 1, 2016. Published December 2016. Originally approved in 1991. Last previous edition approved in 2010 as D378 – 10. — 13 p. These test methods (and references) cover the procedures for evaluating the physical properties of flat conveyor belting. Performance criteria for belting will not be detailed here, but can be found through the RMA (Rubber...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2008. Published August 2008. 4 р. This test method describes the measurement of the resistance of textile fabrics to bursting using a hydraulic or pneumatic diaphragm bursting tester. This test method is generally applicable to a wide variety of textile products.
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2013. Published January 2013. Originally approved in 1979. Last previous edition approved in 2012 as D3786–12. 4 p. This test method describes the measurement of the resistance of textile fabrics to bursting using a hydraulic or pneumatic diaphragm bursting tester. This test method is generally...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1979. Last previous edition approved in 1999 as D 3792 – 99. 4 p. This test method is for the determination of the total water content of waterborne paints. It has been evaluated for latex systems (styrene-butadiene, poly(vinylacetate)-acrylic,...
Current edition approved May 1, 2012. Published July 2012. Originally approved in 1933. Last previous edition approved in 2006 as D380 – 94 (2006). — 10 p. These test methods cover procedures for inspection and test of all types and constructions of rubber hose.
Current edition approved May 1, 2017. Published July 2017. Originally approved in 1979. Last previous edition approved in 2011 as D3832 – 79 (2011). — 3 p. This specification covers the general requirements for materials used in preformed rubber seals that contact the circulating liquid in solar energy systems. Particular applications may necessitate other requirements that would...
American Society for Testing and Materials (ASTM). Current edition approved November 10, 2002. Published January 2003. Originally approved in 1979. Last previous edition approved in 1996 as D 3835 – 96. This test method covers measurement of the rheological properties of polymeric materials at various temperatures and shear rates common to processing equipment. It covers...
Current edition approved Dec. 1, 2012. Published February 2013. Originally approved in 1979. Last previous edition approved in 2007 as D3847 – 01 (2007). — 3 p. This practice covers the general requirements for achieving and maintaining temperatures below 21°C for thermal conditioning and physical testing of rubber. This practice describes the acceptable types and construction of...
Current edition approved Nov. 1, 2013. Published January 2014. Originally approved in 1980. Last previous edition approved in 2009 as D3848 – 03 (2009). — 5 p. These test methods specify the standard materials, test formula, mixing procedures, and test methods for the evaluation of acrylonitrile-butadiene rubber (NBR) mixed with carbon black.
Current edition approved Nov. 1, 2014. Published November 2014. Originally approved in 1980. Last previous edition approved in 2014 as D3849 – 14. — 8 p. This test method covers (1) the morphological (for example, size and shape) characterization of carbon black from transmission electron microscope images which are used to derive the mean particle and aggregate size of carbon...
Current edition approved May 1, 2017. Published May 2017. Originally approved in 1979. Last previous edition approved in 2012 as D3853 – 12. — 4 p. This terminology is a compilation of abbreviations for accelerators, vulcanizing agents, activators, antidegradants, plasticizers, softeners, processing aids, blowing agents, retarders, isocyanates, peroxides, and antireversion agents...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1979. Last previous edition approved in 1999 as D 3872 – 86 (1999). 3 p. This test method covers the quantitative determination of ferrous oxide (FeO) by oxidation of ferrous iron (Fe++) in an acid solution to the ferric state (Fe+++) and...
Current edition approved June 1, 2016. Published July 2016. Originally approved in 1980. Last previous edition approved in 2011 as D3896 – 07 (2011). — 2 p. This practice, intended for referee purposes, covers a uniform procedure for sampling lots of solid synthetic rubbers. Raw synthetic rubber generally is marketed in bales or packages of various sizes. A procedure for...
Current edition approved June 1, 2015. Published July 2015. Originally approved in 1980. Last previous edition approved in 2010 as D3900 – 05a (2010). — 11 p. These test methods cover the determination of the proportion of ethylene and propylene units in ethylenepropylene copolymers (EPM) and ethylene-propylenediene terpolymers (EPDM) over the range from 35 to 85 mass % ethylene....
Current edition approved May 1, 2012. Published July 2012. Originally approved in 1980. Last previous edition approved in 2004 as D3902 – 90 (2004)ε1. — 3 p. This test method covers the determination of the volume of liquefied petroleum gas diffusing through the wall of a hose during a specified period of time.
Current edition approved June 1, 2015. Published August 2015. Originally approved in 1980. Last previous edition approved in 2007 as D3903 – 03 (2007). — 4 p. This specification covers the general requirements for the rubber seals used in solar energy systems employing air-heat transport. Examples are duct and damper seals. Particular applications may necessitate other...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2005. Published February 2005. Originally approved in 1980. Last previous edition approved in 1996 as D 3924 – 80 (1996). 2 p. This specification defines the standard atmospheres for normal conditioning and testing of paint, varnish, lacquer, and related materials, at approximately ambient...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published July 2005. Originally approved in 1980. last previous edition approved in 1999 as D 3926 – 80 (1999). 3 p. These test methods cover the determination of the weight percent of solids in aqueous slurries of titanium dioxide pigments by either the use of a gravity-convection oven...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1980. Last previous edition approved in 2000 as D 3928 – 00a. 3 p. This test method covers the determination of the uniformity of gloss or sheen of a paint applied by brush to a test panel simulating an interior wall section. Variations in gloss or...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2008. Published June 2008. 6 p. These test methods cover the testing of rubber intended for use in applications in which the rubber will be subjected to compressive stresses in air or liquid media. They are applicable particularly to the rubber used in machinery mountings, vibration dampers, and...
Current edition approved April 15, 2016. Published May 2016. Editorially corrected 1.1 in March 2017. Originally approved in 1934. Last previous edition approved in 2015 as D395 – 15. — 8 p. These test methods cover the testing of rubber intended for use in applications in which the rubber will be subjected to compressive stresses in air or liquid media. They are applicable...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 15, 2010. Published September 2010. Originally approved in 1980. Last previous edition approved in 2004 as D3951 – 98 (2004). 3 p. This practice establishes minimum requirements for packaging of supplies and equipment, exclusive of ammunition, explosives, or hazardous materials, as covered in Title 49...
Current edition approved June 1, 2016. Published July 2016. Originally approved in 1980. Last previous edition approved in 2011 as D3958 – 06 (2011). — 5 p. These test methods cover the standard materials, test formula, mixing procedures, and test methods for the evaluation of halogenated isobutene-isoprene rubbers (BIIR and CIIR). Both mill and miniature internal mixer procedures...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 1981. Last previous edition approved in 2004 as D 3960 – 04. 6 p. This practice measures the volatile organic compound (VOC) content of solventborne and waterborne paints and related coatings as determined from the quantity of material released...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1980. Last previous editions approved in 1999 as D 3970 – 80 (1999). 3 p. This test method covers the titrimetric determination of cerium in liquid cerium and rare earth paint driers and utilizes ferrous ammonium sulfate. This test method is...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2010. Published November 2010. Originally approved in 1981. Last previous edition approved in 2005 as D3985 – 05. 7 p. This test method covers a procedure for determination of the steady-state rate of transmission of oxygen gas through plastics in the form of film, sheeting, laminates,...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1981. Last previous edition approved in 1999 as D 3988 – 85 (1999). 3 p. This test method covers the titrimetric determination of vanadium in liquid vanadium driers and utilizes the disodium salt of ethylenediaminetetraacetic acid dihydrate...
Current edition approved May 1, 2017. Published May 2017. Originally approved in 1981. Last previous edition approved in 2012 as D4004 – 06 (2012). — 6 p. These test methods cover the determination of lead, zinc, copper, and manganese in raw rubber and rubber compounds, vulcanized or unvulcanized. The level at which the metals are present is taken into account by suitable...
Current edition approved June 1, 2015. Published September 2015. Originally approved in 1981. Last previous edition approved in 2010 as D4005 – 92 (2010). — 2 p. This test method describes a simple procedure to determine the completeness of fusion of poly(vinyl chloride) (PVC) dispersion coatings on fabric. This test applies primarily to coatings with a mechanical bond and does...
American Society for Testing and Materials (ASTM). Current edition approved July 15, 2008. Published August 2008. 5 p. This test method covers a distillation test for cutback asphaltic (bituminous) products. This procedure measures the amount of the more volatile constituents in cutback asphaltic products. The properties of the residue after distillation are not necessarily...
Current edition approved May 1, 2017. Published May 2017. Originally approved in 1981. Last previous edition approved in 2012 as D4026 – 06 (2012). — 6 p. This test method covers the determination of the residual styrene content of styrene butadiene (SBR) latex. This test method is based upon direct injection of a diluted latex into a gas chromatograph. The amount of residual...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published July 2005. Originally approved in 1981. Last previous edition approved in 1999 as D 4040 – 99. 9.p This test method covers the procedure for determining the falling-rod viscosity and degree of non-Newtonian behavior of printing inks, vehicles, and similar liquids that are...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2014. Published January 2015. Originally approved in 1981. Last previous edition approved in 2010 as D4060 – 10. 5 p. This test method covers the determination of the resistance of organic coatings to abrasion produced by the Taber Abraser on coatings applied to a plane, rigid surface, such as a...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published December 2006. Originally approved in 1982. Last previous edition approved in 2001 as D 4065 - 01. This practice is for general use in gathering and reporting dynamic mechanical data. It incorporates laboratory practice for determining dynamic mechanical properties of plastic...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 15, 2008. Published September 2008. Originally approved in 1982. Last previous edition approved in 2001 as D 4066 - 01a. 19 p. This classification system covers nylon materials suitable for injection molding and extrusion. Some of these compositions are also suitable for compression molding and...
Current edition approved May 1, 2017. Published May 2017. Originally approved in 1981. Last previous edition approved in 2012 as D4075 – 06 (2012). — 4 p. These test methods cover the determination of metals in rubber compounding materials by flame atomic absorption.
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2007. Published March 2007. Originally approved in 1982. Last previous edition approved in 2001 as D 4092 - 01. This terminology is a compilation of definitions and descriptions of technical terms used in dynamic mechanical property measurements on polymeric materials, including solutions, melts,...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 15, 2006. Published January 2007. 14 p. These test methods cover procedures used to evaluate the tensile (tension) properties of vulcanized thermoset rubbers and thermoplastic elastomers. These methods are not applicable to ebonite and similar hard, low elongation materials.
Current edition approved Nov. 1, 2016. Published December 2016. Originally approved in 1935. Last previous edition approved in 2015 as D412 – 15a. — 14 p. These test methods cover procedures used to evaluate the tensile (tension) properties of vulcanized thermoset rubbers and thermoplastic elastomers. These methods are not applicable to ebonite and similar hard, low elongation...
Current edition approved Jan. 1, 2017. Published January 2017. Originally approved in 1982. Last previous edition approved in 2015 as D4122 – 10a (2015). — 6 p. This practice covers guidelines for the production and testing for uniformity of a lot of carbon black to be used as an Industry Reference Black (IRB).
Current edition approved Nov. 1, 2013. Published January 2014. Originally approved in 1935. Last previous edition approved in 2007 as D413 – 98 (2007). — 5 p. These test methods cover the determination of the adhesion strength between plies of fabric bonded with rubber or the adhesion of the rubber layer in articles made from rubber attached to other material. They are applicable...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2013. Published July 2013. Originally approved in 1982. Last previous edition approved in 2007 as D4138 – 07a. 6 p. This practice describes the measurement of dry film thickness of coating films by microscopic observation of precision angular cuts in the coating film. Use of these procedures may...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1982. Last previous edition approved in 1999 as D 4144 – 94 (1999). 2 p. This method covers procedures for testing the package stability of coatings intended to be cured by ultraviolet radiation. One procedure is given for clear coatings and...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published September 2007. 2 p. This practice covers the dry preparation of soil samples as received from the field for particle-size analysis and the determination of the soil constants. This practice can be used to prepare samples for particle-size and plasticity tests where it is...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1982. Last previous edition approved in 1999 as D 4212 – 99. 6 p. This test method covers the determination of viscosity of paints, varnishes, lacquers, inks, and related liquid materials by dip-type viscosity cups. This test method is recommended...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 15, 2007. Published October 2007. 8 р. This test method covers the quantitative determination of the distribution of particle sizes in soils. The distribution of particle sizes larger than 75 μm (retained on the No. 200 sieve) is determined by sieving, while the distribution of particle sizes smaller...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2005. Published December 2005. 3 p. This test method, when used in conjunction with a test performed by Test Method D422 on a duplicate soil sample, provides an indication of the natural dispersive characteristics of clay soils. This test method is applicable only to soils with a plasticity...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1983. Last previous edition approved in 1999 as D 4227 – 99. 3 p. This practice provides a standard qualifying method for coating applicators to verify their proficiency and ability to attain the required quality for application of specified...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1983. Last previous edition approved in 1999 as D 4228 – 99. 3 p. This practice provides a standard qualifying method for coating applicators to verify their proficiency and ability to attain the required quality for application of specified...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1983. Last previous edition approved in 2001 as D 4236 – 94 (2001). 5 p. This practice describes a procedure for developing precautionary labels for art materials and provides hazard and precautionary statements based upon knowledge that exists in...
Данные методы испытанием подходят для двух способов сжигания в печи с высокотемпературной трубой при быстром определении содержания серы в опытных образцах угля или кокса. Эти методы описаны в следующем порядке: метод А – высокотемпературное сжигание с процедурой определения путем титрирования кислотой; метод В - высокотемпературное сжигание с процедурой определения путем...
Стандартный метод исследования серы при анализе проб угля и кокса с использованием методов сжигания в высокотемпературной трубчатой печи. 26 стр.
Данные методы исследования охватывают три альтернативные процедуры с использованием методов сжигания в высокотемпературной трубчатой печи с целью быстрого определения содержания серы в пробах угля и кокса.
Данные методы исследования...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1983. Last previous edition approved in 1999 as D 4258 – 83 (1999). 2 p. This practice includes surface cleaning of concrete to remove grease, dirt, and loose material prior to the application of coatings. Procedures include broom cleaning,...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2005. Published June 2005. Originally approved in 1983. Last previous edition approved in 1999 as D 4260 – 88 (1999). 3 p. This practice covers surface preparation of concrete to prepare the surface prior to the application of coatings. This practice is intended to alter the surface profile of...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1983. Last previous edition approved in 1999 as D 4262 – 83 (1999). 2 p. This test method covers procedures for determining the acidity or alkalinity of concrete surfaces prepared by chemical cleaning or etching prior to coating.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1983. Last previous edition approved in 1999 as D 4263 – 83 (1999). 2 p. This test method is used to indicate the presence of moisture in concrete. The values stated in inch-pound units are to be regarded as the standard. The values given...
American Society for Testing and Materials (ASTM). urrent edition approved May 15, 2005. Published June 2005. Originally approved in 1983. Last previous edition approved in 2000 as D 4287 – 00. 3 p. This test method covers the determination of the viscosity of paints, varnishes, and related products at a rate of shear of 12 000 s −1. Paints and varnishes that dry very rapidly...
Current edition approved May 1, 2014. Published May 2014. Originally approved in 1935. Last previous edition approved in 2008 as D429 – 08. — 22 p. These test methods cover procedures for testing the static adhesional strength of rubber to rigid materials (in most cases metals). Method A - Rubber Part Assembled Between Two Parallel Metal Plates. Method B - 90° Stripping...
ASTM International. — 9 p. This test method covers the determination of total sulfur in petroleum and petroleum products that are single-phase and either liquid at ambient conditions, liquefiable with moderate heat, or soluble in hydrocarbon solvents. These materials can include diesel fuel, jet fuel, kerosine, other distillate oil, naphtha, residual oil, lubricating base oil,...
Current edition approved Feb. 1, 2017. Published February 2017. Originally approved in 1983. Last previous edition approved in 2012 as D4295 – 89 (2012). — 2 p. This classification system covers the compounding material commercially known as zinc oxide. The types of zinc oxide used in the rubber industry are related to the production process used. Typical chemical and physical...
Current edition approved May 1, 2012. Published May 2012. Originally approved in 1935. Last previous edition approved in 2006 as D430 – 06ε1. — 10 p. These test methods cover testing procedures that estimate the ability of soft rubber materials to resist dynamic fatigue. No exact correlation between these test results and service is given or implied. This is due to the varied...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1984. Last previous edition approved in 1996 as D 4301 – 84 (1996), which was withdrawn June 2005 and reinstated in September 2005. 3 p. This test method describes a procedure for the determination of total chlorine in epoxy resins and...
American Society for Testing and Materials (ASTM). Current edition approved July 1, approved in 1999 as D 4302 – 99. 9 p. This specification establishes requirements for composition, physical properties, performance, and labeling of artists’ oil, resin-oil, and alkyd paints. This specification covers pigments, vehicles, and additives. Requirements are included for pigment...
Current edition approved Feb. 1, 2017. Published February 2017. Originally approved in 1984. Last previous edition approved in 2012 as D4315 – 94 (2012). — 3 p. These test methods cover chemical and physical tests for zinc oxide that are considered to be important to its use in rubber compounding. The tests appear in the following order: Zinc Oxide Lead and Cadmium Sulfur Heat...
Current edition approved June 1, 2016. Published July 2016. Originally approved in 1984. Last previous edition approved in 2010 as D4316 – 95 (2010). — 2 p. This specification covers requirements for molded, nonfabric reinforced, elastomeric water bottles with closure and screw stopper, generally used with hot or cold water in personal hygiene and health care.
American Society for Testing and Materials (ASTM). Current edition approved Jan. 15, 2010. Published March 2010. 16 p. These test methods cover the determination of the liquid limit, plastic limit, and the plasticity index of soils as defined in Section 3 on Terminology. Two methods for preparing test specimens are provided as follows: Wet preparation method, as described in...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1984. Last previous edition approved in 1999 as D 4358 – 84 (1999). 4 p. This test method determines amounts of lead and chromium in residues obtained from air sampling of lead chromate and lead silico-chromate type pigment dusts. It is not...
This test method covers the procedure for determining the apparent tack of printing inks using a mechanical or electronic model of a three-roller tackmeter. This test method is applicable to paste-type printing inks and vehicles that are essentially nonvolatile under ordinary room conditions.
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1984. Last previous edition approved in 1999 as D 4399 – 90 (1999). 2 p. This test method covers the determination of the electrical conductivity of electrocoat baths or ultrafiltrate samples using commercially available equipment. The values...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2008. Published April 2008. 2p. This practice is intended for use as a summary of nondestructive quality control test methods for determining the integrity of seams used in the joining of flexible sheet materials in a geotechnical application. This practice outlines the test procedures available...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1995. Last previous edition approved in 2002 as D 4446 – 02. 4 p. s test method is designed to evaluate the effectiveness of water-repellent compositions for retarding dimensional changes in coated wood submerged in water. It can also be used to...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2006. Published June 2006. 10p. This test method specifies a procedure for the determination of the kinematic viscosity, n, of liquid petroleum products, both transparent and opaque, by measuring the time for a volume of liquid to flow under gravity through a calibrated glass capillary viscometer....
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2008. Published April 2008. Originally approved in 1985. Last previous edition approved in 2003 as D4473 – 03. This test method covers the use of dynamic-mechanicaloscillation instrumentation for gathering and reporting the thermal advancement of cure behavior of thermosetting resin. It may be...
Current edition approved May 1, 2011. Published July 2011. Originally approved in 1985. Last previous edition approved in 2007 as D4482 – 07. — 10 p. This test method covers the determination of fatigue life of rubber compounds undergoing a tensile-strain cycle. During part of the cycle, the strain is relaxed to a zero value. The specimens are tested without intentionally...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2005. Published January 2006. Originally approved in 1985. Last previous edition approved in 2005 as D 4483 – 05. This practice covers guidelines for evaluating precision and serves as the governing practice for interlaboratory test programs (ITP) used to evaluate precision for test methods as used...
Current edition approved May 1, 2014. Published May 2014. Originally approved in 1985. Last previous edition approved in 2014 as D4483 – 14. — 59 p. This practice covers guidelines for evaluating precision and serves as the governing practice for interlaboratory test programs (ITP) used to evaluate precision for test methods as used in the rubber manufacturing and the carbon black...
Current edition approved June 1, 2016. Published July 2016. Originally approved in 1985. Last previous edition approved in 2011 as D4527 – 99 (2011). — 3 p. This test method covers the procedure for measuring carbon black solvent extractables. This test method determines the total material extracted from carbon black by toluene under specified conditions. The procedure is also...
Current edition approved Feb. 1, 2017. Published February 2017. Originally approved in 1988. Last previous edition approved in 2012 as D4528 – 88 (2012). — 2 p. This classification covers the variety of sulfur grades used in the rubber industry. Typical chemical and physical properties for sulfur are shown. Sulfur is principally used in unsaturated rubbers as a vulcanizing agent.
Current edition approved July 1, 2015. Published October 2015. Originally approved in 1952. Last previous edition approved in 2010 as D454 – 04 (2010). — 4 p. This test method covers a procedure to determine the influence of elevated temperature and air pressure on the physical properties of vulcanized rubber. The results of this test may not give an exact correlation with service...
Current edition approved May 1, 2017. Published May 2017. Originally approved in 1986. Last previous edition approved in 2012 as D4569 – 06 (2012). — 3 p. This test method covers the determination of the acid material, which disassociates in distilled water, that is present in sulfur. The acidity is determined by an electrometric or visual titration.
Current edition approved Feb. 1, 2017. Published February 2017. Originally approved in 1986. Last previous edition approved in 2012 as D4570 – 02 (2012). — 2 p. This test method covers the particle size measurement of the coarse fraction of ground sulfurs. It is limited to measurement of particles greater than 45 μm (No. 325 sieve). If the sulfur is very fine and the screens...
Current edition approved May 1, 2017. Published May 2017. Originally approved in 1986. Last previous edition approved in 2012 as D4571 – 06 (2012). — 4 p. These test methods cover the determination of the loss of volatile materials in various rubber chemicals based on the mass loss upon heating at 70°C. These test methods for the determination of volatile matter include sulfur and...
Current edition approved Feb. 1, 2017. Published February 2017. Originally approved in 1986. Last previous edition approved in 2012 as D4572 – 89 (2012). — 3 p. This test method covers the evaluation of the particle size distribution of the coarse fraction of sulfur. It is limited to the measurement of those particles greater than 45 μm (No. 325 sieve).
Current edition approved July 1, 2014. Published November 2014. Originally approved in 1986. Last previous edition approved in 2009 as D4573 – 03 (2009). — 3 p. This test method covers the determination of the amount of hydrocarbon oils added to oil-treated sulfurs. The test method is employed when the amount of oil added is 1 % or more of the total sample.
Current edition approved May 1, 2017. Published May 2017. Originally approved in 1986. Last previous edition approved in 2012 as D4574 – 06 (2012). — 4 p. These test methods cover the determination of ash content of rubber chemicals. The test methods include the following materials: Sulfur p-Phenylenediamine Antioxidants Benzothiazole Sulfenamide Accelerators
Current edition approved July 1, 2015. Published September 2015. Originally approved in 1986. Last previous edition approved in 2009 as D4575 – 09. — 10 p. These test methods cover the following three types of methods for the determination of ozone content in laboratory test chambers. Method A (UV absorption) is specified for reference or referee purposes and as a means of...
Current edition approved May 1, 2017. Published June 2017. Originally approved in 1986. Last previous edition approved in 2012 as D4578 – 06 (2012). — 3 p. These test methods cover the determination of solvent insoluble materials in a sulfur sample. The two test methods available are: (1) Test Method A, Extraction by Carbon Disulfide, and (2) Test Method B, Extraction by Toluene....
Current edition approved Jan. 1, 2015. Published February 2015. Originally approved in 1986. Last previous edition approved in 2009 as D4583 – 95 (2009). — 4 p. This practice covers (1) a statistical procedure for analyzing the test data generated in the statistical process control of a carbon black manufacturing process; (2) a format for reporting process capability determined...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published July 2005. Originally approved in 1986. Last previous edition approved in 2001 as D 4587 – 01. 6 p. This practice covers the selection of test conditions for accelerated exposure testing of coatings and related products in fluorescent UV and condensation devices conducted according...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2011. Published August 2011. Originally approved in 1986. Last previous edition approved in 2005 as D4587 – 05. 6 p. This practice covers the selection of test conditions for accelerated exposure testing of coatings and related products in fluorescent UV and condensation devices conducted according...
Current edition approved Feb. 1, 2017. Published February 2017. Originally approved in 1986. Last previous edition approved in 2012 as D4620 – 02 (2012). — 2 p. This test method specifies the standard materials, mixing procedure, and test method for ranking zinc-oxide samples according to their specific surface area in a standard test formula based on chloroprene rubber (CR). The...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2008. Published May 1991. Originally approved in 1991. Last previous edition approved in 2003 as D4632 – 91(2003). 4 p. This test method is an index test which provides a procedure for determining the breaking load (grab strength) and elongation (grab elongation) of geotextiles using the grab...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2008. Published March 2008. Originally approved in 1987. Last previous edition approved in 2004 as D4637 – 04. 4 p. This specification covers flexible sheet made from ethylene-propylene-diene terpolymer (EPDM) intended for use in single-ply roofing membranes exposed to the weather. The tests and...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2005. Published January 2006. Originally approved in 1937. Last previous edition approved in 1999 as D 464 – 95 (1999). 3 p. These test methods cover the determination of the saponification number of tall oil and products obtained by the fractionation of tall oil such as rosin, fatty acids and...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2005. Published January 2006. Originally approved in 1937. Last previous edition approved in 2001 as D 465 – 01. 4 p. These test methods are intended for determining the acid number of naval store products as defined in Terminology D 804 including tall oil products, wood and gum rosin, and other...
Current edition approved Feb. 1, 2017. Published February 2017. Originally approved in 1987. Last previous edition approved in 2012 as D4676 – 94 (2012). — 4 p. This classification covers antidegradants used in rubber and where appropriate defines their important chemical and physical characteristics for use in rubber. The general term “antidegradant” describes materials used in...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published November 2006. Originally approved in 1987. Last previous edition approved in 2001 as D 4676 – 94 (2001). This classification covers antidegradants used in rubber and where appropriate defines their important chemical and physical characteristics for use in rubber.
Current edition approved Nov. 1, 2013. Published January 2014. Originally approved in 1987. Last previous edition approved in 2007 as D4677 – 87 (2007). — 2 p. This classification covers the compounding material known as titanium dioxide. It is generally used in rubber compounds to impart whiteness to selected products. Typical chemical and physical properties are included.
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2004. Published January 2005. Originally approved in 1987. Last previous edition approved in 2001 as D 4678 – 94 (2001). This practice covers materials used on an industry-wide basis as reference materials, which are vitally important to conduct product, specification, and development testing in...
Current edition approved July 1, 2015. Published August 2015. Originally approved in 1987. Last previous edition approved in 2015 as D4678 – 15. — 24 p. This practice covers materials used on an industry-wide basis as reference materials, which are vitally important to conduct product, specification, and development testing in the rubber industry. This practice describes the steps...
Current edition approved Jan. 1, 2015. Published February 2015. Originally approved in 1987. Last previous edition approved in 2007 as D4679 – 02 (2007). — 3 p. This specification covers requirements for gloves made of rubber-like latex, whether made of natural or synthetic materials, unsupported with or without a flock lining, intended for household, beautician use, or general...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2003. Published January 2004. Originally approved in 1987. Last previous edition approved in 1996 as D 4695 – 96. 6 p. This guide provides procedural information for measuring pavement surface deflections, directly under, or at locations radially outward (offset) from a known static, steady-state,...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published November 2006. 13 p. This test method covers the required procedures to evaluate the comparative ability of rubber and rubber-like compositions to withstand the effect of liquids.
Current edition approved July 1, 2016. Published July 2016. Originally approved in 1937. Last previous edition approved in 2016 as D471 – 16. — 16 p. This test method covers the required procedures to evaluate the comparative ability of rubber and rubber-like compositions to withstand the effect of liquids. It is designed for testing: (1) specimens of vulcanized rubber cut from...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published July 2005. Originally approved in 1987. Last previous edition approved in 2001 as D 4712 – 97a (2001). 8 p. This guide covers the selection and use of procedures for testing water-reducible coatings, both pigmented and clear, utilizing synthetic latices, synthetic resin emulsions,...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2013. Published January 2013. Originally approved in 1995. Last previous edition approved in 2008 as D4716 – 08. 9 p. This test method covers the procedure for determining the flow rate per unit width within the manufactured plane of geosynthetics under varying normal compressive stresses and a...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published September 2007. 3 p. This practice presents a procedure for calculating the unit weights and water contents of soils containing oversize particles when the data are known for the soil fraction with the oversize particles removed. The practice also can be used to calculate the...
American Society for Testing and Materials (ASTM). Current edition approved April 10, 2002. Published July 2002. 10 р. This test method evaluates the oxidation stability of engine oils for gasoline automotive engines. This test, run at 160°C, utilizes a high pressure reactor pressurized with oxygen along with a metal catalyst package, a fuel catalyst, and water in a partial...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1938. Last previous edition approved in 2000 as D 476 – 00. 3 p. This classification describes seven types of dry pigmentary titanium dioxide products, grouped by composition, typical end use application, and some performance properties....
This standard is issued under the fixed designation D4762; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2004. Published December 2004. 13 p. This test method covers the determination of strength and stress-strain relationships of a cylindrical specimen of either an undisturbed or remolded saturated cohesive soil. Specimens are isotropically consolidated and sheared in compression without drainage...
Current edition approved Feb. 1, 2017. Published February 2017. Originally approved in 1988. Last previous edition approved in 2012 as D4817 – 88 (2012). — 2 p. This classification covers the compounding materials commercially known as stearic acid.
Current edition approved Feb. 1, 2017. Published March 2017. Originally approved in 1988. Last previous edition approved in 2012 as D4818 – 89 (2012). — 4 p. This classification covers vulcanization accelerators and defines their important chemical and physical characteristics. The properties outlined herein are useful for quality control; they can frequently be directly or...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 1988. Last previous edition approved in 1999 as D 4818 – 88(1999). This classification covers vulcanization accelerators and defines their important chemical and physical characteristics. The properties outlined herein are useful for quality control;...
Current edition approved July 1, 2016. Published August 2016. Originally approved in 1988. Last previous edition approved in 2015 as D4821 – 15. — 13 p. This guide covers procedures for using the ASTM Standard Reference Blacks2 (SRBs) and the HT and INR Iodine Number Standards to continuously monitor the precision of those carbon black test methods for which reference values have...
ASTM D 4833 – 07 Standard Test Method for Index Puncture Resistance of Geomembranes and Related Products American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2007. Published January 2008. Originally approved in 1988. Last previous edition approved in 2000 as D 4833 – 00. 4 p. This test method is used to measure the index puncture resistance of...
ASTM, 2013. — 5 p. These test methods measure visually the color of clear polyester and polyether liquids. They apply only to materials whose colors have light-absorption characteristics similar to those of the standards. An alternative method is Test Method D1209. Units — The values stated in SI units are to be regarded as standard. No other units of measurement are included...
Current edition approved Feb. 1, 2017. Published March 2017. Originally approved in 1989. Last previous edition approved in 2012 as D4924 – 89 (2012). — 2 p. This classification is intended to establish a classification system and test methods for petroleum waxes used in rubber compounding primarily as a static protective agent or material for unsaturated rubbers such as...
6 с.
Язык: Английский.
Данные методы испытаний распространяются на определение содержания бария, кальция, фосфора, серы и цинка в не бывших в употреблении смазочных маслах в диапазонах концентраций этих элементов, указанных в таблице
1. Этот диапазон может быть расширен в область более высоких концентраций путем разбавления проб образцов. Присадки также могут измеряться после...
Current edition approved May 1, 2012. Published July 2012. Originally approved in 1989. Last previous edition approved in 2006 as D4934 – 02 (2006). — 3 p. This test method covers a general procedure for the determination of insoluble impurities of sulfenamides in suitable organic solvents.
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published November 2006. Originally approved in 1989. Last previous edition approved in 2002 as D 4934 – 02. This test method covers a general procedure for the determination of insoluble impurities of sulfenamides in suitable organic solvents.
Current edition approved June 1, 2015. Published September 2015. Originally approved in 1989. Last previous edition approved in 2010 as D4936 – 10. — 8 p. This test method covers the determination of assay on mercaptobenzothiazole (MBT) sulfenamides. It is based on a titration of the basic amines liberated upon reduction of the sulfenamides with hydrogen sulfide gas (H2S)2,3 or...
Current edition approved May 1, 2012. Published July 2012. Originally approved in 1989. Last previous edition approved in 2006 as D4937 – 96 (2006)ε1. — 7 p. This test method covers the determination of the purity of Class I, II, and III p-phenylenediamine (PPD) antidegradants as described in Classification D4676 by gas chromatography (GC) detection and area normalization for data...
American Society for Testing and Materials (ASTM). Current edition approved April 28, 1989. Published June 1989. 3 p. These test methods cover two procedures for determining the amount of water picked up by lithographic printing inks in a laboratory mixer. Test method A covers single-point water pickup; Test method B covers the rate of water pickup. Both test methods are...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2009. Published August 2009. Originally approved in 1989. Last previous edition approved in 2007 as D4956 – 07. 11 p. This specification covers flexible, non-exposed glass bead lens and microprismatic, retroreflective sheeting designed for use on traffic control signs, delineators, barricades, and...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2012. Published February 2012. Originally approved in 1989. Last previous edition approved in 2010 as D4966 – 10. 4 p. This test method covers the determination of the abrasion resistance of textile fabrics using the Martindale abrasion tester. Fabrics of all types may be tested by this method but...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. 4 p. This test method covers determination of the penetration of semi-solid and solid bituminous materials. The needles, containers and other conditions described in this test method provide for the determinations of penetrations up to 500.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1917. Last previous edition approved in 1999 as D 50 – 90 (1999). 5 p. These test methods cover procedures for the chemical analysis of yellow, orange, red, and brown pigments containing iron and manganese. The test methods apply specifically...
Американское общество по тестированию и материалам (ASTM). Перевод на русский язык. 9 стр. Этот метод испытаний охватывает определение плотности или относительной плотности сырой нефти, которая является жидкостью при температурах испытаний от 15 до 35 °С. Это приложение применимо для сырой нефти с высоким давлением насыщенных паров, с соблюдением соответствующих мер...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published July 2005. Originally approved in 1996. Last previous edition approved in 2002 as D 5009 – 02. 4 p. This test method covers the evaluation and comparison of the transfer efficiency of spray-applied coatings under controlled laboratory conditions. This test method has been shown...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published July 2005. Originally approved in 1991. Last previous edition approved in 2003 as D 5010 – 03. 7 p. This guide covers a list of test methods, practices, and specifications that can be used for the testing and evaluation of printing inks, printed ink films, and substrates used in...
American Society for Testing and Materials (ASTM). Current edition approved March 15, 2007. Published April 2007. Originally approved in 1989. Last previous edition approved in 2001 as D 5024 - 01. This test method outlines the use of dynamic mechanical instrumentation for determining and reporting the viscoelastic properties of thermoplastic and thermosetting resins as well as...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2006. Published September 2006. Originally approved in 1989. Last previous edition approved in 2001 as D 5026 - 01. This test method outlines the use of dynamic mechanical instrumentation for gathering and reporting the viscoelastic properties of thermoplastic and thermosetting resins and...
Current edition approved May 1, 2012. Published July 2012. Originally approved in 1990. Last previous edition approved in 2006 as D5044 – 06. — 3 p. This test method covers the procedure for estimation of the acidic impurities in benzothiazyl disulfide (MBTS).
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1990. Last previous edition approved in 2002 as D 5044 – 02. This test method covers the procedure for estimation of the acidic impurities in benzothiazyl disulfide (MBTS).
Current edition approved May 1, 2012. Published July 2012. Originally approved in 1990. Last previous edition approved in 2006 as D5051 – 06. — 3 p. This test method covers the determination of assay of benzothiazyl disulfide (MBTS). It is based on a titration of free iodine liberated upon reduction of MBTS, with potassium iodide (KI) in acid medium. The assay is determined as...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1990. Last previous edition approved in 2002 as D 5051 – 02. This test method covers the determination of assay of benzothiazyl disulfide (MBTS). It is based on a titration of free iodine liberated upon reduction of MBTS, with potassium iodide...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published July 2005. Originally approved in 1990. Last previous edition approved in 2001 as D 5066 – 91 (2001). 5 p. This test method covers procedures for determination of the transfer efficiency (using a weight method) under production conditions for in-plant spray application of automotive...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 1990. Last previous edition approved in 1999 as D 5067 - 99. 6 p. This specification establishes requirements for composition, physical properties, performance, and labeling of artists’ watercolor paints. This specification covers pigments,...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1938. Last previous edition approved in 2003 as D 509 – 03. 3 p. These test methods cover procedures for sampling and determining the grade of rosin delivered in commercial bags, barrels, drums or in molten form. Although developed for rosin, these...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 1990. Last previous edition approved in 2005 as D 5098 – 05. 8 p. This specification establishes requirements for composition, physical properties, performance, and labeling of artists’ acrylic emulsion paints. This specification covers...
Current edition approved Nov. 1, 2013. Published January 2014. Originally approved in 1993. Last previous edition approved in 2008 as D5099 – 08. — 9 p. These test methods describe how capillary rheometry may be used to measure the rheological characteristics of rubber (raw or compounded). Two methods are addressed: Method A—using a piston type capillary rheometer, and Method...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2008. Published May 2008. Originally approved in 1993. Last previous edition approved in 2003 as D 5099 – 93 (2003). These test methods describe how capillary rheometry may be used to measure the rheological characteristics of rubber (raw or compounded). Two methods are addressed: Method A—using a...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1991. Last previous edition approved in 1997 as D 5125 – 97. 8 p. This test method covers the determination of the flow time (viscosity) of Newtonian and near-Newtonian paints, and related coatings and products using ISO capillary flow cups.
American Society for Testing and Materials (ASTM). Current edition approved April 15, 2007. Published May 2007. Originally approved in 1990. Last previous edition approved in 1999 as D 5127 – 99. 5 p. This guide provides recommendations for water quality related to electronics and semiconductor-industry manufacturing. Six classifications of water are described, including water for...
Current edition approved Nov. 1, 2015. Published December 2015. Originally approved in 1990. Last previous edition approved in 2011 as D5151 – 06 (2011). — 2 p. This test method covers the detection of holes in medical gloves. This test method is limited to the detection of holes that allow water leakage under the conditions of the test. The smallest hole size that will allow...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2015. Published December 2015. Last previous edition approved in 2008 as D5162 – 08. 5 p. This practice covers procedures for determining discontinuities (a flaw, void, crack, thin spot, foreign inclusion, or contamination in the coating film that significantly lowers the dielectric strength of...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published April 2005. Originally approved in 1991. Last previous edition approved in 2005 as D 5163 – 05. 4 p. This guide covers procedures for establishing a program to monitor the performance of Coating Service Level I coating systems in operating nuclear power plants. Monitoring is an on...
Current edition approved Aug. 1, 2017. Published August 2017. Originally approved in 1991. Last previous edition approved in 2012 as D5193/D5193M – 93 (2012). — 2 p. This test method describes the determination of the retention of air by fabrics coated on one or both sides with rubber.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1991. Last previous edition approved in 2001 as D 5199 – 01. 4 p. This test method is limited to measuring the nominal thickness of geotextiles, smooth surfaced geomembranes, geonets, and geocomposite drainage products.
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published June 2005. Originally approved in 1939 . Last previous edition approved in 2000 as D 520 – 00. 2 p. This specification covers three types of zinc dust, for use as a pigment in paints. The values stated in SI units are to be regarded as the standard. The values given in...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published July 2005. Originally approved in 1991. Last previous edition approved in 2003 as D 5201 – 03a. 6 p. This practice covers procedures commonly used in the paint industry to formulate paints and coating materials. It describes procedures for calculating formulation values for weight...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2013. Published December 2013. Originally approved in 1939. Last previous edition approved in 2008 as D522 – 93a (2008). 4 p. These test methods cover the determination of the resistance to cracking (flexibility) of attached organic coatings on substrates of sheet metal or rubber-type materials....
Current edition approved Sept. 1, 2014. Published October 2014. Originally approved in 1992. Last previous edition approved in 2013 as D5230 – 13. — 5 p. This test method covers a procedure for measuring individual pellet hardness of carbon black by the automated pellet hardness tester.
Current edition approved Nov. 1, 2015. Published December 2015. Originally approved in 1992. Last previous edition approved in 2011 as D5250 – 06(2011). — 3 p. This specification covers certain requirements for poly- (vinyl chloride) gloves used in conducting medical examinations and diagnostic and therapeutic procedures. It also covers poly(vinyl chloride) gloves used in handling...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published July 2005. Originally approved in 1993. Last previous edition approved in 2001 as D 5286 – 01. 5 p. These test methods cover the determination of the transfer efficiency of spray-applied coatings under general plant conditions. Transfer efficiency is the ratio of paint solids...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2007. Published December 2007. Originally approved in 1992. Last previous edition approved in 2007 as D 5289 – 07. This test method covers a method for the measurement of selected vulcanization characteristics of rubber compounds using unsealed and sealed torsion shear cure meters. The two types of...
Current edition approved May 1, 2012. Published June 2012. Originally approved in 1992. Last previous edition approved in 2007 as D5289 – 07a. — 9 p. This test method covers a method for the measurement of selected vulcanization characteristics of rubber compounds using unsealed and sealed torsion shear cure meters. The two types of instruments may not give the same results. An...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1992. Last previous edition approved in 1997 as D 5296 - 97. 13 p. This test method covers the determination of molecular weight (MW) averages and the distribution of molecular weights for linear, soluble polystyrene by liquid highperformance...
Current edition approved Aug. 1, 2014. Published November 2014. Originally approved in 1992. Last previous edition approved in 2009 as D5297 – 95 (2009). — 7 p. These test methods cover the determination of the purity of present commercially available rubber chemical accelerators in the range from 80 to 100 % by high performance liquid chromatography (HPLC) using ultraviolet...
Current edition approved Aug. 1, 2015. Published January 2016. Originally approved in 1939. Last previous edition approved in 2010 as D531 – 00 (2010). — 4 p. This test method covers the determination of the indentation of rubber or rubber-like materials by means of the Pusey and Jones type of plastometer. This apparatus is used to measure the depth of indentation of an indentor,...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2008. Published April 2008. Originally approved in 1992. Last previous edition approved in 2001 as D5319 – 97(2001). 4 p. This specification covers the classification, materials of construction, workmanship, physical requirements, and methods of testing glass-fiber-reinforced polyester composite...
Current edition approved May 1, 2017. Published July 2017. Originally approved in 1993. Last previous edition approved in 2012 as D5376 – 06 (2012). — 4 p. This test method covers the determination of the nitrogen content of polymerized 2,2,4-trimethyl-1,2- dihydroquinoline (TMQ). It is based on a potentiometric titration of an acetone solution of TMQ with perchloric acid in...
Current edition approved Feb. 1, 2017. Published March 2017. Originally approved in 1993. Last previous edition approved in 2012 as D5377 – 93 (2012). — 2 p. This classification covers the compounding material known as ground coal. It is generally used in rubber compounds as a filler. There are three grades of ground coal based on particle size, ash, and moisture. The selected...
This standard is issued under the fixed designation D5379/D5379M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
Current edition approved June 1, 2016. Published July 2016. Originally approved in 1993. Last previous edition approved in 2011 as D5406 – 93 (2011). — 3 p. This practice provides a calculation procedure and a format for reporting the process performance of a manufacturing operation for a rubber or rubber product. This practice is specifically designed to be used for technically...
Current edition approved May 1, 2017. Published July 2017. Originally approved in 1993. Last previous edition approved in 2012 as D5460 – 02 (2012). — 3 p. This test method covers a procedure for the determination of water in 2-mercaptobenzothiazole sulfenamide accelerators by a Karl Fischer coulometric titration.
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published November 2006. Originally approved in 1993. Last previous edition approved in 2002 as D 5460 – 02. This test method covers a procedure for the determination of water in 2-mercaptobenzothiazole sulfenamide accelerators by a Karl Fischer coulometric titration.
Current edition approved May 1, 2017. Published July 2017. Originally approved in 1993. Last previous edition approved in 2012 as D5461 – 06 (2012). — 3 p. This test method covers a procedure for the qualitative evaluation of aggregate size and aggregate size distribution of powdered rubber accelerators and other compounding materials which are insoluble in water.
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1994. Last previous edition approved in 2003 as D 5531 - 94 (2003). 4 p. This guide covers three levels of physical product standards for color or appearance, or both, commonly used in the coatings industry, provides terminology to describe each...
Current edition approved May 1, 2013. Published August 2013. Originally approved in 1994. Last previous edition approved in 2007 as D5538 – 07. — 2 p. This practice covers a uniform, consensus nomenclature approach for thermoplastic elastomers. This compilation is intended to accommodate and supplement any existing trade names and trademarks. No attempt is made to develop an...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 15, 2007. Published October 2007. 5 p. This test method covers the measurement of the resistance to plastic flow of cylindrical specimens of bituminous paving mixture loaded on the lateral surface by means of the Marshall apparatus. This test method is for use with mixtures containing asphalt cement...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2006. Published January 2006. Originally approved in 1994. Last previous edition approved in 1998 as D 5602 – 98. 3 p. This test method covers evaluation of the maximum static puncture load that roofing membrane samples can withstand without allowing the passage of water. This laboratory test is...
Current edition approved June 15, 2015. Published October 2015. Originally approved in 1996. Last previous edition approved in 2008 as D5603 – 01 (2008). — 4 p. This classification covers the compounding material commercially known as recycled vulcanizate particulate rubber. Recycled vulcanizate particulate rubber is the product that results when vulcanizate rubber has been...
Current edition approved Feb. 1, 2017. Published March 2017. Originally approved in 1994. Last previous edition approved in 2012 as D5604 – 96 (2012). — 6 p. These test methods cover a procedure to measure the surface area of precipitated hydrated silicas by, a single point approximation of the Brunauer, Emmett, and Teller (B.E.T.)2 theory of multilayer gas adsorption. These test...
Current edition approved June 1, 2016. Published July 2016. Originally approved in 1994. Last previous edition approved in 2011 as D5605 – 94 (2011). — 2 p. This practice covers a means for producers and users of emulsion styrene-butadiene rubber (SBR) to establish commontarget values for the Mooney viscosity of these rubbers. Mooney viscosity is a widely used measurement for...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1994. Last previous edition approved in 2000 as D 5618 – 94 (2000). 2 p. This test method covers the measurement of barnacle adhesion in shear to surfaces exposed in the marine environment. It is used to establish the ability of a surface to...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1994. Last previous edition approved in 1999 as D 5629 - 99. 3 p. This test method measures the acidity, expressed as ppm of hydrochloric acid (HCl), in aromatic isocyanate or polyurethane prepolymer samples of below 100 ppm acidity. The test...
Current edition approved Nov. 1, 2013. Published January 2014. Originally approved in 1994. Last previous edition approved in 2008 as D5644 – 01 (2008)ε1. — 4 p. These test methods describe the procedures for determining average particle size distribution of recycled vulcanizate particulate. Method A describes the Ro-tap sieve test method for 60 mesh or coarser particles. Method B...
Current edition approved Aug. 1, 2014. Published November 2014. Originally approved in 1995. Last previous edition approved in 2009 as D5666 – 95 (2009). — 4 p. This test method covers the purity of Type I, II, and III p-phenylenediamine (PPD) antidegradants as described in Classification D4676 by high performance liquid chromatography (HPLC) using ultraviolet detection and...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2004. Published December 2004. Originally approved in 1995. Last previous edition approved in 2000 as D 5666 - 95 (2000). This test method covers the purity of Type I, II, and III p-phenylenediamine (PPD) antidegradants as described in Practice D 4676 by high performance liquid chromatography...
Current edition approved June 1, 2015. Published September 2015. Originally approved in 1995. Last previous edition approved in 2010 as D5667 – 95 (2010). — 2 p. This test method covers a test method for the determination of ash content in synthetic rubber.
Current edition approved July 1, 2014. Published November 2014. Originally approved in 1995. Last previous edition approved in 2009 as D5668 – 09. — 3 p. These test methods cover a hot mill method, two oven methods, and a press method for the determination of moisture and other volatile matter content in synthetic rubber. Either oven method shall be used especially when the rubber...
Current edition approved Aug. 1, 2014. Published November 2014. Originally approved in 1995. Last previous edition approved in 2009 as D5670 – 95 (2009). — 5 p. This test method covers the percentage of residual unsaturation (double bonds in unhydrogenated butadiene) in hydrogenated nitrile rubber and is based on infrared examination of rubber films cast from solution. This test...
ASTM International, 2013. — Официальный перевод выполнен: ФБУ «КВФ «ИНТЕРСТАНДАРТ», Москва 2015. — 25 с. Область применения: Эти методы испытаний охватывают определение никеля, ванадия и железа в сырой нефти и остаточном топливе с помощью атомно-эмиссионной спектрометрии с индуктивно связанной плазмой (ICP). Представлены два разных метода испытаний. Метод испытаний A (разделы...
Current edition approved July 1, 2015. Published September 2015. Originally approved in 1995. Last previous edition approved in 2010 as D5712 – 10. — 9 p. This test method covers an analytical test for determining the amount of total aqueous extractable protein associated with NR, latex, and elastomeric products. Water soluble proteins are extracted in a buffer solution and...
Current edition approved July 1, 2015. Published October 2015. Originally approved in 1940. Last previous edition approved in 2010 as D572 – 04 (2010). — 4 p. This test method covers a procedure to determine the relative deterioration resistance of vulcanized rubber in a high temperature and high pressure oxygen environment. There may be no exact correlation between this...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 1995. Last previous edition approved in 1999 as D 5724 – 99. 8 p. This specification establishes requirements for composition, physical properties, performance, and labeling of gouache paints. This specification covers pigments, vehicles, and...
Current edition approved July 1, 2015. Published October 2015. Originally approved in 1940. Last previous edition approved in 2010 as D573 – 04 (2010). — 6 p. This test method covers a procedure to determine the influence of elevated temperature on the physical properties of vulcanized rubber. The results of this test method may not give an exact correlation with service...
Current edition approved Jan. 1, 2012. Published March 2012. Originally approved in 1940. Last previous edition approved in 2007 as D575 – 91 (2007). — 4 p. These test methods cover two test procedures for determining the compression-deflection characteristics of rubber compounds other than those usually classified as hard rubber and sponge rubber.
Current edition approved Aug. 1, 2014. Published November 2014. Originally approved in 1995. Last previous edition approved in 2009 as D5774 – 95 (2009). — 7 p. These test methods cover the chemical analysis of extractables from synthetic rubbers and are intended for general use on solid uncompounded styrene-butadiene copolymers commonly referred to as SBR. Analysis of other...
Current edition approved Aug. 1, 2014. Published November 2014. Originally approved in 1995. Last previous edition approved in 2009 as D5775 – 95 (2009)ε1. — 4 p. This test method covers the determination of styrene content, and is intended for general use on solid uncompounded styrene-butadiene copolymers, commonly referred to as SBR, prepared by the emulsion process. SBR...
ASTM International. — 4 p. This test method determines the amount of brominereactive material in aromatic hydrocarbons and is thus a measure of trace amounts of unsaturates in these materials. It is applicable to materials having bromine indexes below 500.
Current edition approved Aug. 1, 2014. Published November 2014. Originally approved in 1995. Last previous edition approved in 2009 as D5805 – 00 (2009). — 4 p. These test methods cover the determination of the amount of carbon black in a masterbatch and cover emulsion SBR-carbon black mixtures, but may be applicable to other polymers. Three test methods are included: Inert...
Current edition approved June 1, 2014. Published November 2014. Originally approved in 1995. Last previous edition approved in 2008 as D5817 – 03a (2008). — 4 p. This practice describes the procedure for blending of pelleted carbon black, the procedure for the reduction of gross samples of pelleted carbon black to the appropriate size for testing and the preparation of the sample...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1996. Last previous edition approved in 2004 as D 5857 - 04. 20 p. This specification covers polypropylene materials suitable for injection molding and extrusion. Polymers consist of polypropylene homopolymers, polypropylene copolymers, and...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published July 2005. Originally approved in 1996. Last previous edition approved in 1996 as D 5894 – 96. 3 p. This practice covers basic principles and operating practice for cyclic corrosion/UV exposure of paints on metal, using alternating periods of exposure in two different cabinets: a...
Current edition approved Nov. 1, 2013. Published January 2014. Originally approved in 1996. Last previous edition approved in 2008 as D5899 – 98 (2008). — 3 p. This classification is intended to establish a method to find compounding materials on a computer data base by both functional and chemical classification. This classification will include rubber compounding materials or...
Current edition approved June 1, 2016. Published July 2016. Originally approved in 1996. Last previous edition approved in 2015 as D5900 – 15c. — 5 p. This specification covers the chemical and physical quality specifications or requirements, or both, for Industry Reference Materials (IRMs) as cited in Practice D4678 and other standards. IRMs, as evaluated and referenced in...
Current edition approved June 1, 2015. Published September 2015. Originally approved in 1996. Last previous edition approved in 2010 as D5902 – 05 (2010). — 3 p. This test method covers the Wiijs procedure for the determination of unsaturation (iodine value) in hydrogenated nitrile rubbers. This test method is applicable only to those hydrogenated nitrile rubbers derived from...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published January 2006. Originally approved in 1996. Last previous edition approved in 1996 as D 5910 – 96 which was withdrawn December 2004 and reinstated in October 2005. 6 p. This test method is used for the determination of free formaldehyde (HCHO) in emulsion polymers without upsetting...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1996. Last previous edition approved in 2002 as D 5948 - 96(02). 18 p. This specification covers the basic properties of thermoset molding compounds and the test methods used to establish the properties.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1996. Last previous edition approved in 1999 as D 5958 - 99. 6 p. These practices describe laboratory procedures for preparing an oil-based ink resin solution in a high-boiling solvent using four pieces of lab equipment; (1) a hot oil...
Current edition approved July 1, 2015. Published September 2015. Originally approved in 1997. Last previous edition approved in 2010 as D5963 – 04 (2010)ɛ1. — 9 p. This test method covers the measurement of abrasion resistance of rubbers (vulcanized thermoset rubbers and thermoplastic elastomers) that are subject to abrasive/frictional wear in actual service. The abrasion...
Current edition approved Feb. 1, 2016. Published February 2016. Originally approved in 1996. Last previous edition approved in 2015 as D5964 – 15a. — 10 p. This practice covers three immersion oils to be used as replacements forASTM No. 1, No. 2, and No. 3 immersion oils as called for in Test Method D471. The immersion oils will be designated as IRM 901 as a replacement for...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2005. Published February 2006. Originally approved in 1996. Last previous edition approved in 2000 as D 5974 – 00. 6 p. These test methods cover the determination of the amounts of the individual fatty acids and rosin acids in fractionated tall oil products, using capillary gas chromatographic...
American Society for Testing and Materials (ASTM). Current edition approved July 15, 2005. Published August 2005. Originally approved in 1998. Last previous edition approved in 2003 as D 5989 - 03. 7 p. This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded and cast sheet, plate, rod and tubular bar...
Current edition approved May 1, 2011. Published July 2011. Originally approved in 1996. Last previous edition approved in 2006 as D5992 – 96 (2006)ε1. — 25 p. This guide covers dynamic testing of vulcanized rubber and rubber-like (both hereinafter termed “rubber” or “elastomeric”) materials and products, leading from the definitions of terms used, through the basic mathematics and...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2006. Published December 2006. 3 p. This test method covers the determination of the loss in mass (exclusive of water) of oil and asphaltic compounds when heated as hereinafter prescribed. This test method is useful in characterizing certain petroleum products by the determination of their loss...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 1996. Last previous edition approved in 1996 as D 6038 – 96. 5 p. These test methods cover the manual and automatic procedures for testing the compatibility of lithographic ink resins in high boiling ink solvents by precipitation temperature...
Current edition approved Nov. 1, 2015. Published December 2015. Originally approved in 1996. Last previous edition approved in 2014 as D6047 – 99 (2014). — 8 p. These test methods cover the determination of the content of 5-ethylidenenorbornene (ENB) or Dicyclopentadiene (DCPD) in ethylene-propylene-diene (EPDM) terpolymers. They are applicable to diene contents in the 0.1 to 10...
Current edition approved May 1, 2012. Published July 2012. Originally approved in 1996. Last previous edition approved in 2007 as D6048 – 07. — 15 p. This practice covers several different techniques for determining the stress relaxation characteristics of rubber and rubberlike materials and for the possible interconversion of this stress relaxation information into dynamic...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. Published June 2007. Originally approved in 1996. Last previous edition approved in 2002 as D 6048 – 02. This practice covers several different techniques for determining the stress relaxation characteristics of rubber and rubberlike materials and for the possible interconversion of this...
Current edition approved Nov. 1, 2013. Published January 2014. Originally approved in 1996. Last previous edition approved in 2008 as D6049 – 03 (2008). — 9 p. This test method is an adaptation of the German Standard DIN 53514, a further development of the former “Defo Test” (see Appendix X1). This test method is capable of measuring and characterizing the rheological behavior...
Current edition approved June 1, 2016. Published July 2016. Originally approved in 1997. Last previous edition approved in 2011 as D6085 – 97 (2011). — 7 p. This practice covers a standardized terminology and some basic concepts for testing and sampling across the broad range of chemical and physical testing operations characteristic of the rubber and carbon black manufacturing...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2012. Published November 2012. Originally approved in 1941. Last previous edition approved in 2008 as D610 – 08. 6 p. This practice covers the evaluation of the degree of rusting on painted steel surfaces. The visual examples which depict the percentage of rusting given in the written...
American Society for Testing and Materials (ASTM). Current edition approved February 1, 2005. Published February 2005. Originally approved in 1997. Last previous edition approved in 2003 as D 6109 - 03. 7 p. These test methods are suitable for determining the flexural properties for any solid or hollow manufactured plastic lumber product of square, rectangular, round, or other...
American Society for Testing and Materials, 2010. — 7 с. These test methods cover the determination of the aniline point of petroleum products and hydrocarbon solvents. Test Method A is suitable for transparent samples with an initial boiling point above room temperature and where the aniline point is below the bubble point and above the solidification point of the...
Current edition approved May 1, 2017. Published July 2017. Originally approved in 2000. Last previous edition approved in 2011 as D6124 – 06 (2011). — 5 p. This test method covers the determination of average powder or filter-retained mass found on a sample of medical gloves as described in the introduction. The average powder mass per glove is reported in milligrams. The safe and...
Current edition approved Nov. 1, 2014. Published December 2014. Originally approved in 1997. Last previous edition approved in 2008 as D6147 – 97 (2008)ε1. — 7 p. This standard specifies two methods for determining the decrease in counterforce exerted by a test specimen of vulcanized rubber or thermoplastic elastomer which has been compressed at a constant deformation under...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2008. Published February 2008. Originally approved in 1997. Last previous edition approved in 2002 as D 6147 – 97 (2002). This standard specifies two methods for determining the decrease in counterforce exerted by a test specimen of vulcanized rubber or thermoplastic elastomer which has been...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 10, 2000. Published January 2001. 4 p. In general, the physical and electrical properties of plastics are influenced by temperature and relative humidity in a manner that materially affects test results. In order that reliable comparisons may be made of different materials and between different...
American Society for Testing and Materials (ASTM). Current edition approved April 10, 2003. Published May 2003. Originally approved in 1997. Last previous edition approved in 1997 as D 6195 - 97. 5 p. These test methods cover the determination of properties of a pressure-sensitive adhesive. These test methods are applicable to those adhesives that form a bond of measurable...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2007. Published July 2007. Originally approved in 1997. Last previous edition approved in 2005 as D 6204 – 05. This test method covers the use of a rotorless oscillating shear rheometer for the measurement of the flow properties of raw rubber and unvulcanized rubber compounds. These flow properties...
Current edition approved Nov. 1, 2015. Published December 2015. Originally approved in 1997. Last previous edition approved in 2012 as D6204 – 12. — 12 p. This test method covers the use of a rotorless oscillating shear rheometer for the measurement of the flow properties of raw rubber and unvulcanized rubber compounds. These flow properties are related to factory processing.
Current edition approved May 1, 2012. Published July 2012. Originally approved in 1941. Last previous edition approved in 2005 as D622 – 99 (2005). — 5 p. These test methods are intended for use in testing the conventional types of hose employed for the operation of air brake and vacuum brake systems,2 either on a single motor vehicle or as connecting or transmission lines in a...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2005. Published June 2005. Originally approved in 1998. Last previous edition approved in 1998 as D 6226 - 98. 7 p. This test method covers cellular plastics, which are composed of membranes or walls of polymer separating small cavities or cells. These cells may be interconnecting (open cell),...
Current edition approved May 1, 2014. Published May 2014. Originally approved in 1941. Last previous edition approved in 2007 as D623 – 07. — 7 p. These test methods may be used to compare the fatigue characteristics and rate of heat generation of different rubber vulcanizates when they are subjected to dynamic compressive strains.
Current edition approved Jan. 1, 2012. Published March 2012. Originally approved in 1941. Last previous edition approved in 2007 as D624 – 00 (2007). — 9 p. This test method describes procedures for measuring a property of conventional vulcanized rubber and thermoplastic elastomers called tear strength.
American Society for Testing and Materials (ASTM). Current edition approved July 10, 2000. Published September 2000. 9 p. This test method describes procedures for measuring a property of conventional vulcanized rubber and thermoplastic elastomers called tear strength
Описание стандартных методик определения некоторых элементов (F, Na, Mg, Al, Si, P, S, Ca, Ti, Cr, Zn) в полиолефинах методом волновой рентгенофлуоресцентной спектроскопии
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 1998. Last previous edition approved in 2000 as D 6266 – 00a. 8 p. This test method describes the determination of the amount of volatile organic compound (VOC) released from applied waterborne automotive coatings that is available for delivery to...
This standard is issued under the fixed designation D6272; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
Current edition approved Jan. 1, 2017. Published April 2017. Originally approved in 1998. Last previous edition approved in 2009 as D6284 – 09. — 8 p. This test method covers procedures for evaluating the ability of rubber and rubber-like materials to withstand the effects of aqueous solutions with available chlorine and chloramine. It is intended to compare the effects of...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1998. Last previous edition approved in 1998 as D 6287 - 98. 3 p. This practice covers equipment and techniques for cutting film and sheeting specimens for testing.2 The specimens are nick-free, non stretched and can be rapidly prepared. The...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2005. Published June 2005. Originally approved in 1998. Last previous edition approved in 1998 as D 6290 - 98. 5 p. This test method is intended primarily for the instrumental measurement of the degree of yellowness (or change of degree of yellowness) under daylight illumination of homogeneous,...
Current edition approved Nov. 1, 2015. Published December 2015. Originally approved in 1999. Last previous edition approved in 2005 as D6319 – 10. — 4 p. This specification covers certain requirements for nitrile rubber gloves used in conducting medical examinations and diagnostic and therapeutic procedures. This specification covers nitrile rubber examinationgloves that fit...
Current edition approved June 1, 2017. Published July 2017. Originally approved in 1999. Last previous edition approved in 2011 as D6324 – 11. — 14 p. This specification covers the minimum requirements for individually packaged male condoms made from polyurethane. This specification also describes the minimum inspection and quality levels that shall be utilized in referee tests....
This test method covers the quantitative determination of total sulfur in gasoline and gasoline-oxygenate blends. The Pooled Limit of Quantitation (PLOQ) was determined to be 15
mg/kg. Therefore, the practical range for this test method is from 15 to 940 mg/kg
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1998. Last previous edition approved in 2004 as D 6339 - 04. 6 p. This specification covers syndiotactic polystyrene materials including homopolymer, copolymers, blends, and impact modified, suitable for molding and extrusion. Recycled product...
Страниц: 6 ASTM International 100 Barr Harbor Dr., West Conshohocken This test method covers the determination of total mercury in natural gas streams down to 0.001 μg/m3. It includes procedures to both obtaining a representative sample and the atomic fluorescence detection of the analyte. This procedure can be applied for both organic and inorganic mercury compounds.
Current edition approved May 1, 2017. Published July 2017. Originally approved in 1998. Last previous edition approved in 2012 as D6355 – 07 (2012). — 7 p. This test method is designed to evaluate the potential of glove materials under test to induce and elicit Type IV skin sensitization reactions (that is, allergic contact dermatitis) in humans.
Current edition approved Aug. 1, 2014. Published November 2014. Originally approved in 1999. Last previous edition approved in 2009 as D6370 – 99 (2009). — 4 p. This test method provides a thermogravimetric (TGA) technique to determine the amounts of organics (oil, polymer), carbon black and ash (filler) in a rubber compound. The amount of plasticizer/oil may be determined...
American Society for Testing and Materials (ASTM). Current edition approved December 1, 2003. Published January 2004. 15 p. This test method covers the determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, humidity, and testing machine...
American Society for Testing and Materials (ASTM). Current edition approved December 1, 2003. Published January 2004. 15 р. This test method covers the determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, humidity, and testing machine...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2010. Published June 2010. 16 р. This test method covers the determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, humidity, and testing machine speed.
American Society for Testing and Materials (ASTM). Current edition approved July 1 2005. Published August 2005. Originally approved in 1999. Last previous edition approved in 1999 as D 6386 – 99. 4 p. This practice describes methods of preparing surfaces of new and weathered hot-dip galvanized steel for painting. Hot-dip galvanized steel is produced by the immersion of fabricated...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2005. Published June 2005. Originally approved in 1999. Last previous edition approved in 2003 as D 6394 - 03. 6 p. This specification covers the classification of sulfone plastics suitable for injection molding and extrusion. The properties included in this specification are those required to...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1999. Last previous edition approved in 2000 as D 6419 – 00. 3 p. This test method describes a procedure for determination of the weight percent volatile content of sheet-fed and coldset web offset printing inks. Test specimens are heated at...
American Society for Testing and Materials (ASTM). Current edition approved December 1, 2007. Published January 2008. 48 р. This practice covers the determination of roads and parking lots pavement condition through visual surveys using the Pavement Condition Index (PCI) method of quantifying pavement condition. The PCI for roads and parking lots was developed by the U.S. Army...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 1999. Last previous edition approved in 1999 as D 6437 - 99. 3 p. This test method covers measuring alkalinity in lowalkalinity ( 0.002 meq/g basicity) polyols. This alkalinity is often expressed as CPR (controlled polymerization rate) of...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published July 2005. Originally approved in 1999. Last previous edition approved in 1999 as D 6438 – 99. 4 p. This test method is for the determination of acetone, methyl acetate, or parachlorobenzotrifluoride (PCBTF), or combination of any of the three, in paints and coatings, by solid phase...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 1999. Last previous edition approved in 1999 as D 6441 – 99a. 8 p. These test methods determine and report the hiding power of a powder coating with respect to two parameters: 1 Test Method A—Contrast Ratio at a given film thickness 2 Test...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 1999. Last previous edition approved in 2003 as D 6442 - 03. 10 p. This test method covers the laboratory determination of the rate at which copper is released from an antifouling coating in substitute ocean water. The practical limits for...
American Society for Testing and Materials (ASTM). Current edition approved August 10, 2001. Published October 2001. 13 p. This test method covers the determination of the temperature at which an arbitrary deformation occurs when specimens are subjected to an arbitrary set of testing conditions. This test method applies to molded and sheet materials available in thicknesses of...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005. Published July 2005. Originally approved in 1999. Last previous edition approved in 2001 as D 6486 – 01. 3 p. This practice covers the protocol for vehicle service exposure testing of automotive coatings. Such exposure testing is valuable for the verification of the performance of automotive...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2005. Published December 2005. Originally approved in 1999. Last previous edition approved in 2004 as D 6488 – 04. 6 p. This terminology standard gives definitions for problems that develop with printed matter as a result of deficiencies in the ink, substrate, press, or combinations thereof....
Current edition approved July 1, 2016. Published August 2016. Originally approved in 2000. Last previous edition approved in 2012 as D6499 – 12. — 9 p. This test method covers an immunological method to determine the amount of antigenic protein in natural rubber and its products using rabbit antisera specific for natural rubber latex (NRL) proteins. This immunoassay procedure...
Current edition approved July 1, 2016. Published August 2016. Originally approved in 2000. Last previous edition approved in 2010 as D6515 – 00 (2010). — 7 p. This test method covers a procedure to determine the recovery response of rubber after particular bending deformation, subsequent to aging in selected media at a specified temperature, and for a specified time period, thus...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 2000. Last previous edition approved in 2000 as D 6531 – 00. 3 p. This test method covers the procedure for determining the relative tinting strength of waterbased ink systems using a computer-aided spectrophotometer. This test method is...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2007. Published November 2007. Originally approved in 2000. Last previous edition approved in 2004 as D 6556 – 04. This test method covers the determination of the total surface area by the Brunauer, Emmett, and Teller (B.E.T. NSA) theory of multilayer gas adsorption behavior using multipoint...
Current edition approved Jan. 1, 2016. Published February 2016. Originally approved in 2000. Last previous edition approved in 2014 as D6556 – 14. — 6 p. This test method covers the determination of the total surface area by the Brunauer, Emmett, and Teller (B.E.T. NSA) theory of multilayer gas adsorption behavior using multipoint determinations and the external surface area based...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. Originally approved in 2000. Last previous edition approved in 2000 as D 6580 – 00. 3 p. This test method covers the determination by differential scanning calorimetry of the metallic zinc content of both zinc-dust pigment, and of dried films of zinc-rich coatings. This...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2005. Published June 2005. Originally approved in 2000. Last previous edition approved in 2000 as D 6585 - 00. 4 p. This specification covers unsintered extruded films or tapes manufactured from virgin, unpigmented polytetrafluoroethylene, in nominal thickness from 0.025 to 0.51 mm [0.001 to 0.020...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1944. Last previous edition approved in 2000 as D 660 – 93 (2000). 10 p. The illustrated reference standards included in this test method are representative of degrees and types of checking of exterior paint films. These standards are...
Current edition approved Nov. 1, 2013. Published January 2014. Originally approved in 2000. Last previous edition approved in 2009 as D6600 – 00 (2009). — 16 p. This practice covers testing to evaluate chemical constituents, chemical and physical properties of compounding materials, and compounded and cured rubbers, which may frequently be conducted by one or more test methods....
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2008. Published June 2008. Originally approved in 2000. Last previous edition approved in 2002 as D 6601 – 02. This test method covers the use of a rotorless oscillating shear rheometer for measuring after cure dynamic properties at predetermined temperature(s) below the cure temperature.
Current edition approved Nov. 1, 2015. Published December 2015. Originally approved in 2000. Last previous edition approved in 2012 as D6601 – 12. — 13 p. This test method covers the use of a rotorless oscillating shear rheometer for measuring after cure dynamic properties at predetermined temperature(s) below the cure temperature. Specified cure conditions that approximate a...
Current edition approved Nov. 1, 2013. Published December 2013. Originally approved in 2000. Last previous edition approved in 2010 as D6602 – 03b (2010)ε1. — 22 p. This practice covers sampling and testing for distinguishing ASTM type carbon black, in the N100 to N900 series, from other environmental particulates. This practice requires some degree of expertise on the part of the...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1942. Last previous edition approved in 2000 as D 661 – 93 (2000). 3 p. This test method covers the evaluation of the degree of cracking of exterior paints by comparison with photographic standards.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1942. Last previous edition approved in 2000 as D 662 – 93 (2000). 3 p. This test method covers the evaluation of the degree of erosion of exterior paints by comparison with photographic standards.
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published July 2005. Originally approved in 2001. Last previous edition approved in 2001 as D 6631 – 01. 3 p. This guide covers a simplified statistical procedure for planning and conducting interlaboratory evaluations of test
American Society for Testing and Materials (ASTM). Current edition approved June 10, 2001. Published August 2001. 4 р. This specification covers joint and crack sealants of the hot applied type intended for use in sealing joints and cracks in Portland Cement Concrete and Asphaltic Concrete Pavements.
This practice covers the selection of test conditions for accelerated exposure testing of coatings and related products in xenon arc devices conducted according to Practices G 151 and G
155. This practice also covers the preparation of test specimens, the test conditions suited for coatings, and the evaluation of test results. Table 1 describes commonly used test conditions.
Current edition approved Nov. 1, 2015. Published December 2015. Originally approved in 2001. Last previous edition approved in 2011 as D6738 – 11. — 2 p. This test method covers a procedure to determine the volatile content of precipitated hydrated silicas. These volatiles are generally excess water adsorbed onto the surface of the silica. This test method does not determine water...
Current edition approved Nov. 1, 2015. Published December 2015. Originally approved in 2001. Last previous edition approved in 2011 as D6739 – 11. — 2 p. This test method is used to measure the pH of a 5 % silica/water suspension or mechanical dispersion and is indicative of the relative acidity or alkalinity of the silica.
Current edition approved June 1, 2015. Published July 2015. Originally approved in 2001. Last previous edition approved in 2010 as D6740 – 10. — 3 p. This test method covers the determination of the residue on ignition of silanes of the type bis- (triethoxysilylpropyl)sulfane, or of admixtures of these silanes and solid carriers, such as carbon black, waxes, or organic polymers.
Current edition approved June 1, 2015. Published September 2015. Originally approved in 2001. Last previous edition approved in 2010 as D6741 – 10. — 4 p. These test methods cover the determination of the sulfur content of silanes, or of admixtures of silane and carbon black, of the type bis-(triethoxysilylpropyl)sulfane. The following test methods are included: Test Method A:...
Current edition approved Nov. 1, 2015. Published December 2015. Originally approved in 2002. Last previous edition approved in 2010 as D6746 – 10. — 6 p. This test method covers methods to evaluate a characteristic of raw rubber or unvulcanized rubber compounds that is designated as green strength. This special strength property for uncured rubbers is an important processing...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2008. Published February 2008. Originally approved in 2002. Last previous edition approved in 2002 as D6760 – 02. 7 p. This test method covers procedures for checking the homogeneity and integrity of concrete in deep foundation such as bored piles, drilled shafts, concrete piles or augercast piles....
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. Originally approved in 2002. Last previous edition approved in 2004 as D 6779 - 04a. 14 p. This classification system covers polyamide materials suitable for molding and extrusion. Some of these compositions are also suitable for application from solution. This...
Current edition approved Nov. 1, 2013. Published January 2014. Originally approved in 2002. Last previous edition approved in 2008 as D6814 – 02 (2008). — 3 p. This test method covers the procedure for determining percent devulcanization from crosslink density measurements of devulcanized rubber and control crumb rubber in the laboratory. Percent devulcanization is a quantitative...
Current edition approved June 1, 2015. Published September 2015. Originally approved in 2002. Last previous edition approved in 2010 as D6843 – 10. — 5 p. This test method covers the characterization of silanes of the type bis-(triethoxysilylpropyl)sulfanes by gas chromatography.
Current edition approved June 1, 2015. Published September 2015. Originally approved in 2002. Last previous edition approved in 2010 as D6844 – 10. — 6 p. This test method covers the characterization of silanes, or of admixtures of silane and carbon black (see 10.4), of the type bis-(triethoxysilylpropyl)sulfane by high performance liquid chromatography.
Current edition approved Jan. 1, 2012. Published February 2012. Originally approved in 2002. Last previous edition approved in 2008 as D6845 – 02 (2008). — 4 p. This test method covers the measurement of the specific surface area of precipitated silicas exclusive of area contained in micropores too small to admit hexadecyltrimethylammonium bromide (cetyltrimethylammonium bromide,...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published April 2005. Originally approved in 2004. Last previous edition approved in 2004 as D 6866 - 04a. 14 p. These test methods do not address environmental impact, product performance and functionality, determination of geographical origin, or assignment of required amounts of...
Current edition approved July 1, 2016. Published August 2016. Originally approved in 2003. Last previous edition approved in 2010 as D6909 – 10. — 2 p. This specification covers requirements for the fluorocarbon terpolymer elastomer used in the manufacture of expansion joints for use in coal-fired utilities and other high temperature industrial applications in which corrosive flue...
Current edition approved May 1, 2017. Published May 2017. Originally approved in 2003. Last previous edition approved in 2012 as D6915 – 12. — 5 p. This practice covers guidelines for the production and testing for uniformity of a set of carbon blacks to be used asStandard Reference Blacks (SRBs).
This standard is issued under the fixed designation D 695; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
Current edition approved May 1, 2013. Published May 2013. Originally approved in 2003. Last previous edition approved in 2008 as D6976 – 08. — 6 p. This specification covers requirements for contraceptive vaginal diaphragms, hereafter called diaphragms. Vaginal barrier devices known as cervical caps, vaginal sponges and female condoms are not included in this specification.
Current edition approved June 1, 2016. Published July 2016. Originally approved in 2004. Last previous edition approved in 2010 as D6977 – 04 (2010). — 4 p. This specification provides certain requirements for polychloroprene rubber gloves used in conducting medical examinations and diagnostic and therapeutic procedures. This specification covers polychloroprene rubber examination...
Current edition approved Jan. 1, 2013. Published April 2013. Originally approved in 2005. Last previous edition approved in 2005 as D6978 – 05. — 3 p. This practice covers a protocol for the assessment of resistance of medical glove materials to permeation by potentially hazardous cancer chemotherapy drugs under conditions of continuous contact. An assessment is made based on the...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. Originally approved in 2003. Last previous edition approved in 2003 as D 6990 – 03. 12 p. This practice establishes a practice for evaluating degree of biofouling settlement on and physical performance of marine coating systems when panels coated with such coating...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2005. Published February 2005. 5 p. This test method covers the procedure for measurements of internal stresses in organic coatings by using the cantilever (beam) method. This method is appropriate for the coatings for which the modulus of elasticity of substrate (Es) is significantly greater...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2009. Published June 2009. 4 р. This test method covers the determination of the relative density and density of semi-solid bituminous materials, asphalt cements, and soft tar pitches by use of a pycnometer.
Current edition approved May 1, 2014. Published May 2014. Originally approved in 2004. Last previous edition approved in 2009 as D7050 – 04 (2009). — 2 p. This practice covers the sorting of natural rubber bales of TSR10 or TSR20 in the factory according to their predictedprocessing performance based on differences in viscoelastic properties. This practice determines which...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. 4 p. This guide describes procedures for the application of brush or roller, or both, applied paint films to sealed wallboard for evaluating application properties. Because both the application and panel evaluation are subjective, this guide should be used only for...
This guide covers several comparable procedures for the quantitative chemical analysis of up to 29 elements in fluid catalytic cracking (FCC) catalyst by X-ray fluorescence spectrometry (XRF). Additional elements may be added.
This guide is applicable to fresh FCC catalyst, equilibrium FCC catalyst, spent FCC catalyst, and FCC catalyst fines
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published July 2005. Originally approved in 2005. Last previous edition approved in 2005 as D 7087 – 05. 4 p. This test method covers the measurement of rust creepage area from a scribe line on painted/coated flat test panels after exposure to corrosive environments. This test method has the...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2005. Published September 2005. 7 p. This practice describes the nondestructive measurement of the dry film thickness of nonmagnetic coatings applied to the surface of ferrous metals using magnetic gages and the nondestructive measurement of the dry film thickness of electrically nonconductive,...
Current edition approved May 1, 2017. Published June 2017. Originally approved in 2004. Last previous edition approved in 2010 as D7102 – 10. — 5 p. This guide covers a selection of methodologies for the determination of bacterial endotoxin on gloves when such a determination is appropriate. As bacteria may continue to grow on non-sterile gloves, reportable endotoxin levels are...
Current edition approved May 1, 2013. Published May 2013. Originally approved in 2006. Last previous edition approved in 2006 as D7103 – 06ε1. — 4 p. This guide is intended to assist in the identification and application of the most appropriate ASTM and associated standards for the assessment, development of specifications, and selection of medical gloves with the ultimate goal of...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. 3 p. This guide delineates recommendations for development of procedures and criteria for designation of personnel as a Nuclear Coatings Specialist involved in work in nuclear facilities. The Nuclear Coatings Specialist is responsible for the technical aspects of...
Current edition approved May 1, 2012. Published July 2012. Originally approved in 2005. Last previous edition approved in 2005 as D7121 – 05. — 4 p. This test method covers a means of determining the resilience of rubber, within a range of impact strain and strain rate, by means of the impacting and measuring apparatus conforming to the requirements described in this test method....
This test method determines the damage resistance of multidirectional polymer matrix composite laminated plates subjected to a drop-weight impact event
This test method covers compression residual strength properties of multidirectional polymer matrix composite laminated plates, which have been subjected to quasi-static indentation per Test Method D6264/D6264M or drop-weight impact per Test Method D7136/D7136M prior to application of
compressive force. The composite material forms are limited to continuous-fiber reinforced...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2009. Published July 2009. Originally approved in 1943. Last previous edition approved in 2002 as D714–02. 6 p. This test method employs photographic reference standards to evaluate the degree of blistering that may develop when paint systems are subjected to conditions which will cause...
Current edition approved June 1, 2016. Published December 2016. Originally approved in 2005. Last previous edition approved in 2010 as D7160 – 05 (2010). — 7 p. This practice covers all surgeon’s and examination gloves made from either synthetic or natural rubber latex. The purpose of this practice is to establish methods for testing medical gloves and analyzing the data to...
Current edition approved June 1, 2016. Published June 2016. Originally approved in 2005. Last previous edition approved in 2010 as D7161 – 05 (2010). — 2 p. This practice covers all surgeon’s and examination gloves, made from either synthetic or natural rubber latex, marketed at the time this practice is published, for which there is no previous real time aging data available,...
American Society for Testing and Materials (ASTM). Current edition approved May 15, 2005, 2005. Published July 2005. 3 p. This test method covers the procedure for determining the specular gloss of printed matter. This test is applicable to prints on any flat substrate including paper, paperboard, metallic foil and plastic produced by any printing process, either in the...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2005. Published July 2005. 5 p. This guide covers procedures for establishing a program to monitor the performance of Coating Service Level III lining (and coating) systems in operating nuclear power plants. Monitoring is an ongoing process of evaluating the condition of the in-service lining...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published September 2005. 15 p. This terminology standard covers terms used in the description of printing inks, printing materials, and printing processes. This terminology standard does not include definitions related to Print Problems (see Terminology D 6488).
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published September 2005. 3 p. This test method covers the laboratory procedure for determining the relative mileage of news inks on newsprint. The test method utilizes a proofing press, analytical balance and a reflection densitometer.
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published July 2005. 2 p. This practice covers the ability of a latex paint film to resist staining caused by the leaching of water-soluble materials when contacted with water shortly after application. Water staining is attributed to the leaching of surfactants or other water-soluble...
Current edition approved Dec. 1, 2012. Published February 2013. Originally approved in 2005. Last previous edition approved in 2005 as D7198 – 05. — 6 p. This specification covers certain requirements for natural rubber (Latex), synthetic rubber (Polychloroprene and Nitrile), and vinyl (PVC) disposable gloves for use in conducting single-use embalming procedures. This...
7 с.
Язык: английский.
Данный метод позволяет определить содержание масла в нефтяных парафинах, имеющих температуру застывания 30°C (86°F) или выше, как определено в соответствии с Методом испытаний D 938, и содержание масла в которых не превышает 15%.
Current edition approved Nov. 1, 2015. Published December 2015. Originally approved in 2006. Last previous edition approved in 2011 as D7246 – 06(2011)ɛ1. — 3 p. This test method covers the detection of holes in polyethylene food service gloves. This test method shall not be used on any medical glove. This test method is limited to the detection of holes that allow water leakage...
American Society for Testing and Materials (ASTM). Current edition approved April 15, 1994. Published June 1994. Originally published as D726 – 43 T. Last previous edition D726 – 58(1971). 3 p. This test method covers the determination of the resistance of nonporous paper to the passage of air. This test method cannot be used in those cases where the paper cannot be clamped...
Current edition approved Dec. 1, 2012. Published February 2013. Originally approved in 2007. Last previous edition approved in 2007 as D7329 – 07. — 5 p. This specification covers the properties necessary for thin film, unlined polymer gloves to be used in food preparation and food handling. This specification is intended to serve as a referee and a guide to permit obtaining...
This practice covers information relating to sampling,
calibration and validation of X-ray fluorescence instruments
for elemental analysis, including all kinds of wavelength
dispersive (WDXRF) and energy dispersive (EDXRF) tech-
niques. This practice includes sampling issues such as the
selection of storage vessels, transportation, and sub-sampling.
Treatment, assembly, and...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2012. Published August 2012. Originally approved in 1943 . Last previous edition approved in 2008 as D737 – 04(2008). 5 p. This test method covers the measurement of the air permeability of textile fabrics. This test method applies to most fabrics including woven fabrics, nonwoven fabrics, air...
Current edition approved Nov. 1, 2013. Published January 2014. Originally approved in 2008. Last previous edition approved in 2008 as D7426 – 08. — 4 p. This test method covers the assignment of the glass transition temperatures (Tg) of materials using differential scanning calorimetry. This test method is applicable to amorphous materials, including thermosets or semicrystaline...
Current edition approved June 1, 2016. Published July 2016. Originally approved in 2008. Last previous edition approved in 2014 as D7427 – 14. — 15 p. This test method covers an immunological method known as an immunoenzymetric assay to quantify the amount of 4 principal Hevea brasiliensis [Hev b] allergenic proteins [Hev b 1, Hev b 3, Hev b 5 and Hev b 6.02] in Hevea natural...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2008. Published May 2008. 10 p. This practice applies to the measurement of moisture content of solid wood, including solid wood products containing additives, that is, chemicals or adhesives, by hand-held moisture meters under conditions of end-use. This practice includes calibration, use, and...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2007. Published March 2007. 8 p. This test method covers the determination of the temperature at which plastics and elastomers exhibit brittle failure under specified impact conditions. Two routine inspection and acceptance procedures are also provided.
American Society for Testing and Materials (ASTM). Current edition approved April 10, 2002. Published June 2002. 6 p. This test method covers the determination of the apparent bending modulus2 of plastics by means of a cantilever beam. It is well suited for determining relative flexibility of materials over a wide range. It is particularly useful for materials too flexible to be...
1 Current edition approved June 1, 2017. Published July 2017. Originally approved in 1943. Last previous edition approved in 2012 as D750 – 12. — 4 p. This practice covers specific variations in the test conditions and procedures that shall be applicable when Practice G151 plus either Practice G152, G153, G154, or G155 are employed for exposure of vulcanized rubber compounds. It...
Current edition approved Nov. 1, 2011. Published January 2012. Originally approved in 1943. Last previous edition approved in 2006 as D751 – 06. — 19 p. These test methods cover, but are not limited to, rubber-coated fabrics, that is, tarpaulins, rainwear, and similar products. The test methods appear in the following sections: Dimensions and Mass Breaking Strength Procedure...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2006. Published May 2006. Originally approved in 1943. Last previous edition approved in 2000 as D 751 – 00. 19 p. These test methods cover, but are not limited to, rubber-coated fabrics, that is, tarpaulins, rainwear, and similar products. The scope of each of these test methods appears in the...
Current edition approved Nov. 1, 2014. Published December 2014. Originally approved in 2009. Last previous edition approved in 2009 as D7558 – 09. — 5 p. This test method is designed to quantify the amount of total extractable accelerators in natural rubber latex (NRL) and nitrile gloves. Three common classes of rubber accelerators, the mercaptobenzothiazole (MBT), thiuram, and...
Описание стандартных способов калибровки, используемых в различных методах элементного анализа нефтепродуктов и смазочных материалов. Calibration in Empirical Test Methods Calibration in Photometric Test Methods Calibration in Electrometric Test Methods Calibration in Atomic Absorption Spectrometry Calibration in ICP-AES Test Methods Calibration in XRF Test Methods
Current edition approved Nov. 1, 2013. Published December 2013. Originally approved in 2010. Last previous edition approved in 2010 as D7633 – 10b. — 3 p. This test method covers the instrumental determination of carbon content in a carbon black sample. Values obtained represent the total carbon content. The method is applicable to tread, carcass and specialty type carbon blacks...
Current edition approved Oct. 1, 2010. Published November 2010. — 14 p. This test method covers procedures used to detect a shift in physical properties of non-lubricated natural rubber latex (NRL) condoms after immersion in a personal lubricant. “Personal lubricants” are lubricants such as liquids or gels that are applied by the consumer at the time of condom use. This test...
Current edition approved June 15, 2015. Published September 2015. Originally approved in 2010. Last previous edition approved in 2013 as D7662 – 13. — 4 p. This test method covers the instrumental determination of carbon content in samples of carbon black feedstock oils. Values obtained represent the total carbon content. This test method is applicable to carbon black feedstock...
Current edition approved Jan. 1, 2016. Published February 2016. Originally approved in 2010. Last previous edition approved in 2013 as D7679 – 13. — 5 p. This test method covers the instrumental determination of sulfur content in samples of carbon black feedstock oils. Values obtained represent the total sulfur content. Two analysis methods are available for use: Test Method A:...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published December 2005. Originally approved in 1944. Last previous edition approved in 2000 as D 772 – 86 (2000). 4 p. This test method covers the evaluation of the degree of flaking (scaling) of exterior paints by comparison with photographic standards. The values stated in SI units are...
Current edition approved May 1, 2011. Published July 2011. — 4 p. This test method covers a procedure to measure the macro-dispersion of fillers in a rubber matrix by quantifying the surface roughness of a freshly cut specimen using an optical microscope in reflection mode. The method provides a procedure to measure the quality of mixing of reinforcing fillers such as silica and...
Current edition approved June 1, 2016. Published July 2016. Originally approved in 2011. Last previous edition approved in 2011 as D7724 – 11. — 3 p. This test method covers the determination of nondispersible matter after mechanical water flushing of regular untreated carbon blacks. It may not be applicable to oil-treated carbon blacks because the oil would prevent proper wetting...
Current edition approved Jan. 1, 2017. Published January 2017. Originally approved in 2011. Last previous edition approved in 2015 as D7771 – 15. — 10 p. This test method covers the qualitative and quantitative determination of only benzo-α-pyrene (BaP), a specific polycyclic aromatic hydrocarbon (PAH), on carbon black. The procedure involves Soxhlet extraction with toluene and...
Current edition approved June 1, 2015. Published September 2015. Originally approved in 2011. Last previous edition approved in 2011 as D7772 – 11. — 3 p. This method covers the determination of extinction (absorbance) of carbon black cyclohexane extract at 386 nm using a UV spectrophotometer.
Current edition approved June 1, 2014. Published June 2014. — 2 p. This classification covers instructions for naming the reference materials used by Committee D24.
Current edition approved Jan. 1, 2013. Published January 2013. — 4 p. This specification covers the biological quality specifications or requirements, or both, for Industry Reference Materials (IRMs) as cited in Practice D4678 and other standards. IRMs, as evaluated and referenced in Practice D4678, are vitally important to conduct product, specification, and development testing...
Current edition approved Jan. 1, 2016. Published February 2016. Originally approved in 2013. Last previous edition approved in 2015 as D7854 – 15. — 5 p. This test method covers a procedure to measure a carbon black structure property known as Void Volume at mean pressure. Compressed void volumes are obtained by measuring the compressed volume of a weighed sample in a cylindrical...
Current edition approved Dec. 1, 2014. Published December 2014. Originally approved in 2014. Last previous edition approved in 2014 as D7866 – 14. — 1 p. To describe the requirements for packaged protective gloves with radiation attenuating properties intended to protect the operator or other persons from unnecessary exposure to radiation during radiological procedures by...
American Society for Testing and Materials (ASTM). Current edition approved February 1, 2004. Published March 2004. 7 p. The purpose of this classification system is to provide a method of adequately identifying PMMA materials using a system consistent with that of Classification System D
4000. It further provides a means for specifying these materials by the use of a simple line...
American Society for Testing and Materials (ASTM). Current edition approved March 10, 2003. Published April 2003. 11 p. These test methods cover the determination of flexural properties of unreinforced and reinforced plastics, including high-modulus composites and electrical insulating materials in the form of rectangular bars molded directly or cut from sheets, plates, or molded...
Current edition approved May 1, 2014. Published May 2014. — 8 p. The methods herein specify two analytical tests for quantitatively evaluating surface bactericidal efficacy of medical examination gloves incorporated with bactericidal properties. They may be used for the determination of bactericidal activity on either the outer or inner glove surface. The methods incorporate...
American Society for Testing and Materials (ASTM). Current edition approved June 15, 2008. Published July 2008. 6 p. These test methods describe the determination of the specific gravity (relative density) and density of solid plastics in forms such as sheets, rods, tubes, or molded items.
Current edition approved Jan. 1, 2016. Published January 2016. Originally approved in 2015. Last previous edition approved in 2015 as D7969 – 15. — 4 p. This specification covers the performance requirements for general purpose air ovens ordinarily used in testing operations, which have a testing chamber up to 0.6 m3 (25 ft3) in volume. It is applicable to gravity convection ovens...
Current edition approved June 1, 2015. Published January 2016. — 2 p. This classification system covers the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic robbers, alone or in combination) that are intended for use in rubber products found in natural gas pipeline applications (for example, elastomeric couplings, o-rings, quad seals, and...
Current edition approved Dec. 15, 2015. Published February 2016. — 4 p. This standard gives the testing procedure to determine the change in dimensions of specimens of rubber or elastomeric materials, or both, resulting from exposure to gaseous hydrocarbon environments. The size of the specimens is such to facilitate preparation from as molded component configurations such as...
Current edition approved Nov. 1, 2015. Published December 2015. — 3 p. This test method is used to determine the number of silanol groups on the surface of silica by titration according to a method as developed by Sears. This test method is suitable for characterizing rubber-grade silicas.
Current edition approved July 1, 2016. Published October 2016. — 4 p. This test method covers the use of a sealed cavity rotorless oscillating shear rheometer for the measurement of the softening effects of rising sinusoidal strain when applied to an unvulcanized rubber compound containing significant amounts of colloidal fillers (such as silica or carbon black, or both) from a...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2009. Published November 2009. 6 p. This practice, known as the embrittlement-detector method, covers the apparatus and procedure for determining the embrittling or nonembrittling characteristics of the water in an operating boiler. The interpretation of the results shall be restricted to the...
Current edition approved May 1, 2014. Published May 2014. Originally approved in 1944. Last previous edition approved in 2007 as D813 – 07. — 6 p. This test method covers the determination of crack growth of vulcanized rubber when subjected to repeated bending strain or flexing. It is particularly applicable to tests of synthetic rubber compounds which resist the initiation of...
Current edition approved Nov. 1, 2014. Published December 2014. Originally approved in 1944. Last previous edition approved in 2010 as D814 – 95 (2010). — 2 p. This test method covers the measurement of the rate of vapor transmission of volatile liquids through a rubber sheet, disk, or diaphragm.
Current edition approved July 1, 2016. Published August 2016. Originally approved in 1951. Last previous edition approved in 2011 as D816 – 06 (2011). — 6 p. These test methods cover tests to measure the properties of adhesives, commonly called rubber cements, that may be applied in plastic or fluid form and that are manufactured from natural rubber, reclaimed rubber, synthetic...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2006. Published May 2006. Originally approved in 1951. Last previous edition approved in 2001 as D 816 – 82 (2001). 6 p. These test methods cover tests to measure the properties of adhesives, commonly called rubber cements, that may be applied in plastic or fluid form and that are manufactured from...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2012. Published November 2012. Originally approved in 1945. Last previous edition approved in 2007 as D823 – 95 (2007). 8 p. Five practices are given for preparing films of uniform thickness of coatings on test panels. These practices are: Practice A—Automatic Spray Machine Application Practice...
Current edition approved Dec. 1, 2012. Published February 2013. Originally approved in 1945. Last previous edition approved in 2007 as D832 – 07. — 4 p. This practice covers the characteristic mechanical behavior of rubbers at low temperatures, and outlines the conditioning procedure necessary for testing at these temperatures.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1921. Last previous edition approved in 1999 as D 85 – 87 (1999). 2 p. This specification covers ferrous earthy pigment included under the general term ochre. The pigment may be purchased in the dry form.
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2010. Published March 2010. 7 p. These test methods cover the determination of the specific gravity of soil solids that pass the 4.75-mm (No. 4) sieve, by means of a water pycnometer. When the soil contains particles larger than the 4.75-mm sieve, Test Method C127 shall be used for the soil solids...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2004. Published June 2004. 26 р. This test method covers the atmospheric distillation of petroleum products using a laboratory batch distillation unit to determine quantitatively the boiling range characteristics of such products as natural gasolines, light and middle distillates, automotive...
28 С.
Язык: английский.
Стандартный метод перегонки нефтепродуктов при атмосферном давлении.
Standard Test Method for Distillation of Petroleum Products at atmospheric pressure.
Current edition approved Aug. 15, 2011. Published September 2011. Originally approved in 1946. Last previous edition approved in 2005 as D865 – 99 (2005). — 5 p. This test method covers a procedure to determine the deterioration induced by heating rubber specimens in individual test tube enclosures with circulating air. This isolation prevents cross contamination of compounds due...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2007. Published November 2007. 7 р . This test method covers the empirical procedures for determining the Saybolt Universal or Saybolt Furol viscosities of petroleum products at specified temperatures between 21 and 99°C (70 and 210°F). A special procedure for waxy products is indicated.
American Society for Testing and Materials (ASTM). Current edition approved April 10, 2002. Published June 2002. 10 p. This test method covers the determination of tensile properties of plastics in the form of thin sheeting, including film (less than 1.0 mm (0.04 in.) in thickness). NOTE 1—Film has been arbitrarily defined as sheeting having nominal thickness not greater than...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2011. Published May 2011. Originally approved in 1947 (replacing former D615). Last previous edition approved in 2007 as D910–07a. 8 p. This specification covers formulating specifications for purchases of aviation gasoline under contract and is intended primarily for use by purchasing agencies....
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2005. Published August 2005. 10 p. This test method describes the determination of the flash point and fire point of petroleum products by a manual Cleveland open cup apparatus or an automated Cleveland open cup apparatus.
Current edition approved May 1, 2014. Published May 2014. Originally approved in 1947. Last previous edition approved in 2006 as D925 – 06ε2. — 6 p. These test methods cover techniques to evaluate three types of staining that rubber may cause when in contact with, or in proximity to, another surface that may be light colored. The test methods also describe how to qualitatively...
Current edition approved Nov. 1, 2013. Published January 2014. Originally approved in 1956. Last previous edition approved in 2008 as D926 – 08. — 4 p. This test method covers the determination of plasticity and recovery of unvulcanized rubber by means of the parallel plate plastometer. Uncompounded, compounded, and reclaim rubber may be tested. ISO 2007 and Test Method D3194 use...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2006. Published July 2006. Originally approved in 1948. Last previous edition approved in 2001 as D 945 – 92 (2001)e1. These test methods cover the use of the Yerzley mechanical oscillograph for measuring mechanical properties of rubber vulcanizates in the generally small range of deformation that...
Current edition approved July 1, 2016. Published July 2016. Originally approved in 1948. Last previous edition approved in 2012 as D945 – 06 (2012). — 13 p. These test methods cover the use of the Yerzley mechanical oscillograph for measuring mechanical properties of rubber vulcanizates in the generally small range of deformationthat characterizes many technical applications....
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2010. Published May 2010. 6 p. This test method covers the determination of water in the range from 0 to 25 % volume in petroleum products, tars, and other bituminous materials by the distillation method. The specific products considered during the development of this test method are listed in...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2011. Published July 2011. Originally approved in 1927, replacing D
47. Last previous edition approved in 2009 as D97–09. 5 p. This test method covers and is intended for use on any petroleum product.2 A procedure suitable for black specimens, cylinder stock, and nondistillate fuel oil is...
Current edition approved Nov. 1, 2014. Published December 2014. Originally approved in 1948. Last previous edition approved in 2010 as D991 – 89 (2010). — 5 p. This test method covers the determination of volume resistivity of rubbers used in electrically conductive and antistatic products. This test method assumes that the surface conductivity is negligible compared with the...
Standard Test Method for Bromine Index of Aromatic Hydrocarbons by Coulometric Titration. Перевод: РГП «КазИнСт», Астана Редактор: Баймолдинова А.Б. Кол-во страниц: 9 Кол-во таблиц: 2 Перевод выполнен: 01.03.2012 Редактирование выполнено: 01.03.2012 Область применения Настоящий метод испытаний распространяется на определение количества материала, вступающего в реакцию с бромом...
West Conshohocken: ASTM International, 2001. — 6 p. Scope Referenced documents Terminology Significance and use Apparatus Test specimens Preparation of apparatus Conditioning Procedure Calculation Report Precision and bias Keywords
West Conshohocken: ASTM International, 2003. — 7 p. Scope Referenced documents Terminology Summary of Test method Significance and use Apparatus Materials and Reagents Hazads Sampling and specimen preparation Procedure Calculation Report Precision and bias
West Conshohocken: ASTM International, 2002. — 5 p. Scope Referenced documents Terminology Significance and use Apparatus and materials Sampling Preparation of test specimens Procedure Report Precision and bias Keywords
West Conshohocken: ASTM International, 2003. — 9 p. Scope. Referenced documents. Terminology. Summary of test method. Significance and use. Interferences. Apparatus. Preparation of test pieces. Procedure. Calculation and interpretation of results. Report. Precision and bias. Keywords. Annex.
American Society for Testing and Materials. Reapproved edition, 2014.- 26 p. This document provides practical guidance on the selection and optimization of sample designs in waste management sampling activities, within the context of the requirements established by the data quality objectives or other planning process. This document (1) provides guidance for selection of...
American Society for Testing and Materials - 2017.- 15 p. This guide covers the context of groundwater monitoring at waste disposal facilities. Regulations have required statistical methods as the basis for investigating potential environmental impact due to waste disposal facility operation. Owner/operators must typically perform a statistical analysis on a quarterly or...
American Society for Testing and Materials - 2017.- 3 p. This practice addresses sampling of Organic compounds (i.e., PCBs, dioxins, many Pesticides and similar compounds) from smooth nonporous surfaces using a solvent-wetted wipe sampling method. Samples are collected in a manner that permits the solvent extraction of the Organic compound(s) of interest from the wipes and...
American Society for Testing and Materials, 2011. — 24 с. Элементный анализ микроэлементов используется для определения уровня загрязнения среднедистиллятного топлива. Следы металлов в турбинном топливе могут вызывать коррозию и осаждение на компонентах турбин при повышенных температурах. Некоторые виды дизельного топлива имеют предельные требования по содержанию следов...
American Society for Testing and Materials - 2016.- 6 p. This test method describes a solid phase extraction (SPE) procedure to separate 99Tc from environmental water (non-process-related or effluent water samples). Technetium-99 beta activity is measured by liquid scintillation spectrometry. This test method is designed to measure 99Tc in the range of approximately 0.037 Bq/L...
Standard Test Method for Hydrogen Content of Middle Distillate Petroleum Products by Low-Resolution Pulsed Nuclear Magnetic Resonance Spectroscopy. — ASTM International, 2016. — Официальный перевод выполнен: Госстандарт Республики Казахстан, Астана, 2016. — 15 с. Настоящий метод испытаний распространяется на определение содержания водорода в среднедистиллятных нефтепродуктах с...
American Society for Testing and Materials - 2014.- 25 p. This practice covers consensus criteria for the calibration and quality control of nuclear instruments. This practice is provided for establishing appropriate quality control parameters at instrument startup, calibration of nuclear counting instruments and the continuing monitoring of quality control parameters....
American Society for Testing and Materials - 2017.- 13 p. This test method covers the measurement of gross alpha- and beta- activity concentrations in a homogeneous water sample. It is applicable to alpha emitters with activity concentration levels above 0.11 Bq/L and beta emitters with activity concentration levels above 0.15 Bq/L. This test method is not applicable to samples...
American Society for Testing and Materials - 2014.- 8 p. The objective of this guide is to provide useful information for the interpretation of radiological instrument responses in the event of a radiological incident or emergency. For the purposes of this guide, a radiological incident or emergency is defined as those events that follow the indication of the presence of...
American Society for Testing and Materials - 2014.- 4 p. This guide provides a rapid procedure by which vegetation samples may be screened for surface contamination of radioactive strontium (89Sr and 90Sr, collectively referred to as radiostrontium) following an airborne radioactive dispersal event. It provides a conservative estimate of radiostrontium deposition that can be...
American Society for Testing and Materials. Reapproved edition, 2015.- 8 p. This test method covers the determination of radioactive 210Pb in environmental water samples (for example, drinking, non-process and effluent waters) in the range of 37 mBq/L or greater. The values stated in SI units are to be regarded as standard. The values given in parentheses are provided for...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2010. Published March 2010. DOI: 10.1520/ D7605-10. This test method covers the use of a rotorless oscillating shear rheometer for the measurement of the flow properties of polymer melts and their respective congealed dynamic properties for thermoplastic elastomers (TPE) which includes...
American Society for Testing and Materials - 2012.- 7 p. This practice covers the quantification of radionuclides in environmental media (e.g., water, soil, vegetation, food) by means of simple preparation and counting with a high-resolution gamma ray detector. Because the practice is designed for rapid analysis, extensive efforts to ensure homogeneity or ideal sample counting...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 10, 2001. Published December 2001. Originally published as E 1–
39. Last previous edition E 1–01. 63 p. This specification covers liquid-in-glass thermometers graduated in Celsius (centigrade) or Fahrenheit degrees which are frequently specified in methods of ASTM. The various thermometers covered...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2010. Published June 2010. Originally approved in 1924. Last previous edition approved in 2008 as E10 – 08. 32 p. This test method covers the determination of the Brinell hardness of metallic materials by the Brinell indentation hardness principle. This standard provides the requirements for a...
Publisher: ASTM Publish Date: 2015 Pages: 32 Language: English Format: PDF Size: 334 kB Scope 1.1 This test method covers the determination of the Brinell hardness of metallic materials by the Brinell indentation hardness principle. This standard provides the requirements for a Brinell testing machine and the procedures for performing Brinell hardness tests. 1.2 This standard...
American Society for Testing and Materials (ASTM). 1998, 20 pages.
This guide describes practices and image quality measuring systems for real-time, and near real-time, nonfilm detection, display, and recording of radioscopic images. These images, used in materials inspection, are generated by penetrating radiation passing through the subject material and producing an image on...
American Society for Testing and Materials (ASTM). 1999, 9 pages. This practice describes procedures for the ultrasonic examination of bulk materials or parts by transmitting pulsed, longitudinal waves through a liquid couplant into the material and observing the indications of reflected waves (Fig. 1). It covers only examinations in which one search unit is used as both...
American Society for Testing and Materials (ASTM). 1996, 4 pages.
Test Method A, Pressurization—This test method covers procedures for calibration of ultrasonic instruments, location,and estimated measurements of gas leakage to atmosph ereby
the airborn ultrasonic technique
American Society for Testing and Materials (ASTM). Reapproved 2000, 3 pages.
This test method covers the testing of components for leaks by pressurizing them inside with a liquid. This test method can be used on piping, valves, and containers with welded or fitted sections which can be sealed at their ends and which are designed for internal pressure
American Society for Testing and Materials (ASTM). 1999, 4 pages.
This practice covers a procedure for determining the electrical conductivity of nonmagnetic metals using the electromagnetic (eddy-current) method. The procedure has been written primarily for use with commercially available direct reading electrical conductivity instruments. General purpose
eddy-current...
Scope - This test method covers the determination of the Brinell hardness of metallic materials by the Brinell indentation hardness principle. This standard provides the requirements for a Brinell testing machine and the procedures for performing Brinell hardness tests. This test method includes requirements for the use of portable Brinell hardness testing machines that measure...
American Society for Testing and Materials (ASTM). 1999, 6 pages.
This practice covers the design, material grouping classification, and manufacture of hole-type image quality indicators (IQI) used to indicate the quality of radiologic images.
American Society for Testing and Materials (ASTM). 1995, 11 pages.
This test method provides a uniform procedure for radiographic examination of metallic castings using radiographic film as the recording medium
American Society for Testing and Materials (ASTM). 1995, 5 pages.
This test method provides a uniform procedure for radiographic examination of weldments using industrial radiographic film. Requirements expressed in this method are intended to control the quality of the radiographic images and are not intended for controlling acceptability or quality of
welds
American Society for Testing and Materials (ASTM). 1998, 3 pages.
This practice covers a procedure for in-line, eddycurrent examination of continuously welded (CW) ferromagnetic pipe and tubing at temperatures above the Curie temperature (approximately 1400°F (760°C), where the pipe is substantially nonmagnetic or austenitic.
American Society for Testing and Materials (ASTM). 1999, 21 pages.
This guide covers measurement procedures for evaluating certain characteristics of ultrasonic search units (also known as transducers) that are used with ultrasonic examination
instrumentation. This guide describes means for obtaining performance data that may be used to define the acoustic and electric responses...
American Society for Testing and Materials (ASTM). Reapproved 2000, 5 pages.
This test method covers the testing of large single- and double-walled tanks, pressure and vacuum vessels, laminated, lined- or double-walled parts, complex piping systems, flexible containers (such as aircraft fuel tanks), glass-to-metal seals in hybrid packages, and systems that inherently contain or...
American Society for Testing and Materials (ASTM). 1996, 17 pages.
This practice covers acoustic emission (AE) examination or monitoring of fiberglass-reinforced plastic (FRP) tanksvessels (equipment) under pressure or vacuum to determine structural integrity.
American Society for Testing and Materials (ASTM). 1997, 2 pages.
This practice covers the calibration of transmission densitometers used to perform radiographic film density measurements
Publisher: ASTM Publish Date: 2014 Pages: 5 Language: English Format: PDF Size: 96 kB Scope 1.1 This test method defines the requirements for portable instruments that are intended to be used to measure the Rockwell or Brinell hardness of metallic materials by performing indentation tests on the surface of materials in the field or outside of a test lab, or in cases where the...
American Society for Testing and Materials (ASTM). Reapproved 1997, 12 pages.
This method covers the requirements for the absolute calibration of acoustic emission (AE) sensors. The calibration yields the frequency response of a transducer to waves, at a surface, of the type normally encountered in acoustic emission work. The transducer voltage response is determined at discrete...
American Society for Testing and Materials (ASTM). Reapproved 1997, 4 pages.
This test method covers the determination of the focal size of an iridium-192 radiographic source. The determination is based upon measurement of the image of the iridium metal source in a projection radiograph of the source assembly and comparison to the measurement of the image of a reference sample in...
American Society for Testing and Materials (ASTM). 1995, 12 pages.
This practice covers acoustic emission (AE) examination or monitoring of reinforced thermosetting resin pipe (RTRP) to determine structural integrity. It is applicable to lined or unlined pipe, fittings, joints, and piping systems.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2010. Published December 2010. 27 p. These test methods cover the measurement of average grain size and include the comparison procedure, the planimetric (or Jeffries) procedure, and the intercept procedures. These test methods may also be applied to nonmetallic materials with structures having...
Scope - These test methods cover the measurement of average grain size and include the comparison procedure, the planimetric (or Jeffries) procedure, and the intercept procedures. These test methods may also be applied to nonmetallic materials with structures having appearances similar to those of the metallic structures shown in the comparison charts. These test methods apply...
American Society for Testing and Materials (ASTM). 1997, 5 pages.
This test method describes the techniques for comparing the brightness of the penetrants used in the fluorescent dye penetrant process. This comparison is performed under controlled conditions which eliminate most of the variables present in actual penetrant examination. Thus, the brightness factor is isolated and...
США ASTM International Актуальный стандарт 2016 год ASTM E1136 – 14 - Стандартная спецификация для шин P195 / 75R14 Standard Specification for P195/75R14 Radial Standard Reference Test Tire
American Society for Testing and Materials (ASTM). 1997, 6 pages.
This practice provides guidelines for continuous monitoring of acoustic emission (AE) from metal pressure boundaries in industrial systems during operation. Examples are pressure vessels, piping, and other system components which serve to contain system pressure. Pressure boundaries other
than metal, such as...
American Society for Testing and Materials (ASTM). 1995, 5 pages. This practice covers ultrasonic examination of materials by the pulse-echo method using straight-beam longitudinal waves introduced by direct contact of the search unit with the material being examined.
American Society for Testing and Materials (ASTM). 1998, 4 pages.
This guide covers general procedures for the material selection and fabrication of reference blocks made of metal or metal alloys and intended to be used for the pulsed longitudinal wave ultrasonic examination of the same or similar production materials.
American Society for Testing and Materials (ASTM). 1995, 3 pages.
This test method provides a standard procedure for nondestructive radiographic examination of semiconductor devices, electronic components, and the materials used for construction of these items. This test method covers the radiographic testing of these items for possible defective
conditions such as extraneous...
American Society for Testing and Materials (ASTM). Reapproved 1996, 7 pages.
This test method provides instructions for determining the length and width dimensions of line focal spots in industrial X-ray tubes (see Note 1). This determination is based on the
measurement of an image of a focal spot that has been radiographically recorded with a pinhole projection/imaging...
American Society for Testing and Materials (ASTM). 1999, 7 pages. This test method covers procedures for fluorescent liquid penetrant examination utilizing the lipophilic postemulsification process. It is a nondestructive testing method for detecting discontinuities that are open to the surface such as cracks, seams, laps, cold shuts, laminations, through leaks, or lack of...
American Society for Testing and Materials (ASTM). 1999, 6 pages.
This test method2 covers procedures for water-washable fluorescent penetrant examination of materials. It is a nondestructive testing method for detecting discontinuities that are open to the surface such as cracks, seams, laps, cold shuts, laminations, isolated porosity, through leaks, or lack of porosity and is...
American Society for Testing and Materials (ASTM). 1999, 7 pages.
This test method covers procedures for fluorescent penetrant examination utilizing the hydrophilic postemulsification process. It is a nondestructive testing method for detecting discontinuities that are open to the surface such as cracks, seams, laps, cold shuts, laminations, isolated porosity,
through leaks, or...
American Society for Testing and Materials (ASTM). 1997, 5 pages.
This practice describes a passive method for detecting and locating the steady state source of gas and liquid leaking out of a pressurized system. The method employs surfacemounted
acoustic emission sensors (for noncontact sensors see Test Method E 1002), or sensors attached to the system via acoustic waveguides...
American Society for Testing and Materials (ASTM). 1999, 5 pages.
This practice covers general requirements for the establishment and maintenance of a quality control system for agencies engaged in nondestructive testing (NDT).
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2009. Published March 2009. Originally approved in 1987. Last previous edition approved in 2002 as E 1213 – 97 (2002). 1 p. This test method covers the determination of the minimum resolvable temperature difference (MRTD) capability of the compound observer-thermal imaging system as a function of...
American Society for Testing and Materials (ASTM). 1997, 3 pages.
This test method covers the determination of the minimum resolvable temperature difference (MRTD) capability of the compound observer-thermal imaging system as a function of spatial frequency.
American Society for Testing and Materials (ASTM). 1999, 6 pages. This test method2 covers procedures for fluorescent penetrant examination utilizing the solvent-removable process. It is a nondestructive testing method for detecting discontinuities that are open to the surface, such as cracks, seams, laps, cold shuts, laminations, isolated porosity, through leaks, or lack of...
American Society for Testing and Materials (ASTM). 1999, 6 pages.
This test method2 covers procedures for visible penetrant examination utilizing the solvent-removable process. It is a nondestructive testing method for detecting discontinuities
that are open to the surface such as cracks, seams, laps, cold shuts, laminations, isolated porosity, through leaks, or lack of fusion...
American Society for Testing and Materials (ASTM), Reapproved 1997, 2 pages.
This collection of reference photographs covers types and degrees of discontinuities occurring in steel castings and other types of ferrous castings detectable by the dry powder
magnetic particle method.
These reference photographs are intended to assist in the classification of those discontinuities...
American Society for Testing and Materials (ASTM). 1998, 3 pages.
This guide may be used for the control and maintenance of industrial radiographs and unexposed films used for industrial radiography.
American Society for Testing and Materials (ASTM). 1996, 13 pages.
This practice provides application details for radioscopic examination using penetrating radiation. This includes dynamic radioscopy and for the purposes of this practice, radioscopy where there is no motion of the test object during exposure (referred to as static radioscopic imaging). Since the
techniques...
American Society for Testing and Materials (ASTM). 1998, 13 pages.
This practice covers a procedure for fabricating aluminum alloy ultrasonic standard reference blocks that can be used for checking performance of ultrasonic testing equipment and
for standardization and control of ultrasonic tests of aluminum alloy products using pulsed longitudinal waves introduced into test...
This practice describes procedures to determine the load resistance of specified glass types, including combinations of glass types used in a sealed insulating glass unit, exposed to a uniform lateral load of short or long duration, for a specified probability of breakage.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2010. Published November 2010. Originally approved in 1989. Last previous edition approved in 2004 as E 1311 – 89 (2004). 1 p. This test method covers the determination of the minimum detectable temperature difference (MDTD) capability of a compound observer-thermal imaging system as a function of...
American Society for Testing and Materials (ASTM). Reapproved 1999, 3 pages.
This test method covers the determination of the minimum detectable temperature difference (MDTD) capability of a compound observer-thermal imaging system as a function of the angle subtended by the target.
American Society for Testing and Materials (ASTM). 1999, 3 pages.
This practice covers procedures for eddy-current examination of hot ferromagnetic bars above the Curie temperature where the product is essentially nonmagnetic, but below 2100°F (1149°C).
American Society for Testing and Materials (ASTM). 1993, 4 pages.
This practice describes the selection of single element hard face ultrasonic search units for which flat-entry-surface calibration blocks can be used for examination of steel with convex cylindrically curved entry surfaces
American Society for Testing and Materials (ASTM). 1999, 38 pages. This standard defines the terminology used in the standards prepared by the E-7 Committee on Nondestructive Testing. These nondestructive testing (NDT) methods include: acoustic emission, electromagnetic testing, gamma- and X-radiology, leak testing, liquid penetrant examination, magnetic particle examination,...
American Society for Testing and Materials (ASTM). 1995, 4 pages.
These reference radiographs are reproductions of original radiographs and are supplied as a means for establishing some of the categories and severity levels of discontinuities in titanium castings that may be revealed by radiographic examination. The title is intended to be descriptive and not restrictive. The...
American Society for Testing and Materials (ASTM). 2000, 10 pages.
This guide describes procedures for electronically measuring the following performance-related characteristics of some sections of ultrasonic instruments
American Society for Testing and Materials (ASTM). 1999, 8 pages.
This guide establishes areas for review and provides a survey form that can be used in determining the competence of a nondestructive testing agency.
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2005. Published June 2005. Originally approved in 1990. Last previous edition approved in 2000 as E 1360 – 90 (2000). 15 p. This practice provides a means for specifying the colors of objects in terms of the Optical Society of America Uniform Color Scales. Both computational and visual methods are...
American Society for Testing and Materials (ASTM). 1990, 3 pages.
This guide provides the recommended minimum requirements for illuminators used for viewing industrial film radiographs using transmitted light
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2007. Published January 2007. 21 p. Conversion Table 1 presents data in the Rockwell C hardness range on the relationship among Brinell hardness, Vickers hardness, Rockwell hardness, Rockwell superficial hardness, Knoop hardness, and Scleroscope hardness of nonaustenitic steels including carbon,...
Publisher: ASTM Publish Date: 2012 Pages: 25 Language: English Format: PDF Size: 229 kB Scope 1.1 Conversion Table 1 presents data in the Rockwell C hardness range on the relationship among Brinell hardness, Vickers hardness, Rockwell hardness, Rockwell superficial hardness, Knoop hardness, and Scleroscope hardness of nonaustenitic steels including carbon, alloy, and tool...
American Society for Testing and Materials (ASTM). 1995, 12 pages.
This practice provides test and measurement details for measuring the performance of X-ray and Gamma ray radioscopic systems. Radioscopic examination applications are diverse. Therefore, system configurations are also diverse and constantly changing as the technology advances.
American Society for Testing and Materials (ASTM). 1996, 5 pages.
This test method covers a uniform procedure for radioscopic examination of weldments. Requirements expressed in this test method are intended to control the quality of the
radioscopic images and are not intended for controlling acceptability or quality of welds.
American Society for Testing and Materials (ASTM). 1999, 10 pages.
This practice establishes the minimum requirements forconducting liquid penetran examination of nonporous metal, and nonmetal components
This practice establishes the minimum requirements for conducting liquid penetrant examination of nonporous metal, and nonmetal components This standard is issued under the fixed designation E1417/E1417M; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses...
American Society for Testing and Materials (ASTM). 1999, 6 pages.
This test method describes procedures for visible liquid penetrant examination utilizing the water-washable process. It is a nondestructive test method for detecting discontinuities
that are open to the surface such as cracks, seams, laps, cold shuts, laminations, isolated porosity, through leaks or lack of fusion...
American Society for Testing and Materials (ASTM). 1996, 6 pages.
This test method provides guidelines for acoustic emission (AE) tests of seamless pressure vessels (tubes) of the type used for distribution of industrial gases
American Society for Testing and Materials (ASTM). Current edition approved April 10, 2003. Published July 2003. Originally approved in 1991. Last previous edition approved in 1998 as E 1426 – 98. 4 p. This test method covers a procedure for experimentally determining the effective elastic parameter, Eeff, for the evaluation of residual and applied stresses by X-ray diffraction...
American Society for Testing and Materials (ASTM). 1997, 32 pages.
Computed tomography (CT) is a radiographic method that provides an ideal examination technique whenever the primary goal is to locate and size planar and volumetric detail in three dimensions. Because of the relatively good penetrability of X rays, as well as the sensitivity of absorption cross
sections to atomic...
American Society for Testing and Materials (ASTM). 1994, 12 pages.
This practice establishes minimum requirements for magnetic particle examination used for the detection of surface or slightly subsurface discontinuities in ferromagnetic material. This practice is intended as a direct replacement of MIL-STD- 1949. Guide E 709 can be used in conjunction with this practice as a...
Данная методика устанавливает минимальные требования к магнитопорошковой дефектоскопии, используемой для выявления поверхностных или неглубоких подповерхностных неоднородностей в ферромагнитном материале.
This standard has been approved for use agencies of the Department of Defense
This practice establishes minimum requirements for magnetic particle used the detection of surface or slightly subsurface discontinuities in ferromagnetic material
American Society for Testing and Materials (ASTM). 1996, 2 pages.
This guide may be used for the control and maintenance of recorded and unrecorded magnetic and optical media of analog or digital electronic data from industrial radioscopy.
American Society for Testing and Materials (ASTM). 1997, 5 pages.
This guide provides a listing and description of the fields that are recommended for inclusion in a digital ultrasonic examination data base to facilitate the transfer of such data. This guide is prepared for use particularly with digital image data obtained from ultrasonic scanning systems. The field
listing...
American Society for Testing and Materials (ASTM). 1997, 5 pages.
This guide provides a listing and description of the fields that are recommended for inclusion in a digital radiological test data base to facilitate the transfer of such data. This guide sets
guidelines for the format of data fields for computerized transfer of digital images files obtained from radiographic,...
American Society for Testing and Materials (ASTM). 1997, 13 pages.
This guide is intended for tutorial purposes only. It describes the general requirements, methods, and procedures for the nondestructive identification and sorting of metals.
American Society for Testing and Materials (ASTM). 1997, 9 pages.
This guide explains the rationale and basic technology for the acousto-ultrasonic (AU) method. Guidelines are given for nondestructive evaluation (NDE) of flaws and physical characteristics that influence the mechanical properties and relative strength of composite structures (for example,
filament-wound pressure...
American Society for Testing and Materials (ASTM). 1997, 4 pages.
This test method provides a technique for extracting quantitative dimensional information on an object from its neutron radiograph. The technique is based on the identification
of changes in film density caused by material changes where a corresponding discontinuity in film density exists. This test method is...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2007. Published November 2007 . Originally approved in 1993. Last previous edition approved in 2003 as E 1515 – 03a. 9 p. This test method covers the determination of the minimum concentration of a dust-air mixture that will propagate a deflagration in a near-spherical closed vessel of 20 L or...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2013. Published November 2013. Originally approved in 1993. Last previous edition approved in 2005 as E1527 – 05. 47 p. The purpose of this practice is to define good commercial and customary practice in the United States of America for conducting an environmental site assessment of a parcel of...
American Society for Testing and Materials (ASTM). Curent edition approved Jan. 15, 2014. Published February 2014. Originally approved in 1993. Last previous edition approved in 2006 as E1528– 06. 27 p. Purpose—The purpose of this practice is to define a good practice in the United States of America for conducting a transaction screen for a parcel of commercial real estate where...
American Society for Testing and Materials (ASTM). Current edition approved December 1, 2011. Published March 2012. Originally approved in 1993. Last previous edition approved in 2006 as E 1353 – 00 (2006). 1 p. This test method covers the determination of the noise equivalent temperature difference (NETD; NE[delta]T) of thermal imaging systems of the conventional forward-looking...
American Society for Testing and Materials (ASTM). 2000, 4 pages.
This test method covers the determination of the noise equivalent temperature difference (NETD; NEDT) of thermal imaging systems of the conventional forward-looking infrared
(FLIR) or other types that utilize an optical-mechanical scanner; it does not include charge-coupled devices or pyroelectric vidicons.
American Society for Testing and Materials (ASTM). 1995, 4 pages. These reference radiographs illustrate the types and degrees of discontinuities that may be found in aluminum-alloy and magnesium-alloy castings. The castings illustrated are in thicknesses of 1⁄4 in. (6.35 mm) and 3⁄4 in. (19.1 mm). This document may be used where no other applicable document exists, for other...
American Society for Testing and Materials (ASTM). 2000, 11 pages. This practice is for computed tomography (CT), which may be used to nondestructively disclose physical features or anomalies within an object under examination by providing radiological density and geometric measurements. This practice implicitly assumes the use of penetrating radiation, specifically x-ray and g-ray
American Society for Testing and Materials (ASTM). 1999, 5 pages.
These test methods cover procedures for testing the sources of gas leaking at the rate of 4.4 3 10−14 moles/s (1 3 10−9 standard-cm3/s at 0°C) or greater. These test methods may be conducted on any object that can be evacuated and to the other side of which helium or other tracer gas may be applied. The object must...
American Society for Testing and Materials (ASTM). 1999, 4 pages. This practice covers the procedures that shall be followed in electromagnetic (eddy-current) examination of copper redraw rods for detecting discontinuities or imperfections of a severity likely to cause failure or markedly impair surface quality of the rod. These procedures are applicable for continuous lengths...
American Society for Testing and Materials (ASTM). 1994, 6 pages.
This practice covers a procedure for determining the impedance of absolute eddy-current probes (bridge-type, air or ferrite core, wire wound, shielded, or unshielded) used for finding material defects in electrically conducting material. This practice is intended to establish a uniform test methodology to measure...
American Society for Testing and Materials (ASTM), 1997, 23 pages.
This practice covers techniques for the ultrasonic A-scan examination of specific weld configurations joining wrought ferrous or aluminum alloy materials to detect weld discontinuities (Note 1). The reflection method using pulsed waves is specified. Manual techniques are described employing contact of the search...
American Society for Testing and Materials (ASTM). 1998, 4 pages.
This practice covers the design and material selection of a contrast sensitivity measuring gage used to determine the minimum change in material thickness or density that may be imaged without regard to spatial resolution limitations.
American Society for Testing and Materials (ASTM). 1995, 3 pages.
These reference radiographs illustrate various types and severity levels of discontinuities in aluminum fusion welds that may be revealed by radiographic examination. These reference
radiographs do not specify the acceptable level of these discontinuities, rather they provide a visual reference for communicating...
ASTM, 2014, 13p. E 1652 Standard Specification for Magnesium Oxide and Aluminum Oxide Powder and Crushable Insulators Used in the Manufacture of Base Metal Thermocouples, Metal-Sheathed Platinum Resistance Thermometers, and Noble Metal Thermocouples
Brief Summary
his specification covers the requirements for magnesium oxide (MgO) and aluminum oxide (Al2O3) powders and...
American Society for Testing and Materials (ASTM). 1995, 10 pages. This guide covers guidelines for translating application requirements into computed tomography (CT) system requirements/specifications and establishes a common terminology to guide both purchaser and supplier in the CT system selection process. This guide is applicable to the purchaser of both CT systems and...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published January 2005. Originally approved in 1995. Last previous edition approved in 2001 as E 1682 – 96 (2001). 6 p. This guide is intended for use in establishing the operating characteristics of a visual display unit (VDU), such as a cathode ray tube (CRT). Those characteristics define...
ASTM International, 2013. — 5 p. This test method provides instruction for determining the spatial resolution and contrast sensitivity in X-ray and γ-ray computed tomography (CT) images. The determination is based on the examination of the CT image of a uniform disk of material. The spatial resolution measurement is derived from an image analysis of the sharpness at the edge of...
American Society for Testing and Materials (ASTM). 1995, 4 pages.
This test method provides instruction for determining the spatial resolution and contrast sensitivity in X-ray and g-ray computed tomography (CT) images. The determination is based on examination of the CT image of a uniform disk of material. The spatial resolution measurement is derived from
an image analysis of...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published October 2005. Originally approved in 1995. Last previous edition approved in 2000 as E 1699 – 00. Reapproved 2005. 6 p. This practice covers a procedure for defining and satisfying the requirements of the user’s/owner’s project. A multidisciplinary team uses the procedure to...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published January 2005. Originally approved in 1995. Last previous edition approved in 1997 as E 1710 – 97. 6 p. This test method covers measurement of the retroreflective properties of horizontal pavement marking materials containing retroreflecting beads, such as traffic stripes and surface...
American Society for Testing and Materials (ASTM). 1998, 9 pages.
This practice covers a uniform procedure for radioscopic examination of castings.
This practice applies only to radioscopic examination in which an image is finally presented on a display screen (monitor) for evaluation. Test part acceptance may be based on a static or dynamic image. The examination results may be...
American Society for Testing and Materials (ASTM). 2000, 5 pages.
This test method covers determination of the relative image quality response of industrial radiographic film when exposed to X-radiation sources having photon energies from 4 to 25 MV. Evaluation of the film is based on the visibility of holes in a special image quality indicator (IQI). Since results for a given...
American Society for Testing and Materials (ASTM). 1995. 5 pages. This practice covers a procedure for acousto-ultrasonic (AU) assessment of filament-wound pressure vessels. Guidelines are given for the detection of defect states and flaw populations that arise during materials processing or manufacturing or upon exposure to aggressive service environments. Although this...
American Society for Testing and Materials (ASTM). 1995, 11 pages.
This practice establishes the minimum requirements for radiographic examination for metallic and nonmetallic materials.
American Society for Testing and Materials (ASTM). 1996, 8 pages.
This guide is intended primarily for tutorial purposes. It provides an overview of the general principles governing the
operation and use of electromagnetic acoustic transducers (EMATs) for ultrasonic examination.
США ASTM International Актуальный стандарт 2016 год Стандартная практика для работы с внешними наблюдениями имеет отношение к испытаниям шин и является подстандартом Standard Practice for Dealing With Outlying Observations
American Society for Testing and Materials (ASTM). 1998, 7 pages.
This practice covers requirements for the secondary calibration of acoustic emission (AE) sensors. The secondary
calibration yields the frequency response of a sensor to waves of the type normally encountered in acoustic emission work.
The source producing the signal used for the calibration is mounted on the...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2008. Published January 2009. 37 p. These test methods cover the determination of the Rockwell hardness and the Rockwell superficial hardness of metallic materials by the Rockwell indentation hardness principle. This standard provides the requirements for Rockwell hardness machines and the...
American Society for Testing and Materials (ASTM). 1996, 4 pages.
This practice covers a uniform procedure for the examination of castings by the computed tomography (CT) technique.
The requirements expressed in this practice are intended to control the quality of the nondestructive examination by CT
and are not intended for controlling the acceptability or quality of the...
American Society for Testing and Materials (ASTM). 1996, 6 pages.
This test method covers a procedure for determination of the performance of film systems used for industrial radiography.
This test method establishes minimum requirements that correspond to system classes
Publisher: ASTM Publish Date: 2015 Pages: 38 Language: English Format: PDF Size: 591 kB Scope 1.1 These test methods cover the determination of the Rockwell hardness and the Rockwell superficial hardness of metallic materials by the Rockwell indentation hardness principle. This standard provides the requirements for Rockwell hardness machines and the procedures for performing...
American Society for Testing and Materials (ASTM). 1996, 10 pages.
This practice covers procedures for the use of electromagnetic acoustic transducers (EMATs) for specific ultrasonic
examination applications. Recommendations are given for specific applications for using EMAT techniques to detect
flaws through both surface and volumetric inspections as well as to measure...
American Society for Testing and Materials (ASTM). 1996, 3 pages.
This practice covers the radiological examination of unique materials or processes, or both, for which conventionally
designed image quality indicators (IQIs), such as those described in Practices E 747 and E 1025, may be inadequate in
controlling the quality and repeatability of the radiological image.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2013. Published January 2014. Originally approved in 1996. Last previous edition approved in 2011 as E1820 – 11. 54 p. This test method covers procedures and guidelines for the determination of fracture toughness of metallic materials using the following parameters: K, J, and CTOD (δ). Toughness...
Publisher: ASTM
Publish Date: 2015
Pages: 54
Language: English
Format: PDF
Document Scope
1.1 This test method covers procedures and guidelines for
the determination of fracture toughness of metallic materials
using the following parameters: K, J, and CTOD (δ). Toughness
can be measured in the R-curve format or as a point value.
The fracture toughness determined in...
Publisher: ASTM Publish Date: 2013 Pages: 25 Language: English Format: PDF Size: 716 kB Scope 1.1 This terminology contains definitions, definitions of terms specific to certain standards, symbols, and abbreviations approved for use in standards on fatigue and fracture testing. The definitions are preceded by two lists. The first is an alphabetical listing of symbols used....
American Society for Testing and Materials (ASTM). 1998, 3 pages. These reference radiographs2 for heavy-walled steel castings are applicable to nominal section thicknesses of 2 to 41⁄2 in. (51 to 114 mm) and consists of three separate sets as follows: Volume 1: 1–MV X Rays and Iridium 192 (called 1 to 2–Mev X rays in previous editions)-Set of 28 plates (5 by 8 in. (127 by 203...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2010. Published March 2011. Originally approved in 1997. Last previous edition approved in 2002 as E 1862 – 97 (2002). 1 p. This practice covers procedures for measuring and compensating for reflected temperature when measuring the surface temperature of a specimen with an infrared imaging...
American Society for Testing and Materials (ASTM). 1997, 3 pages.
These test methods cover procedures for measuring and compensating for reflected temperature when measuring the
surface temperature of a specimen with an infrared imaging radiometer.
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2010. Published August 2010. Originally approved in 1997. Last previous edition approved in 2009 as E1868 – 09. 6 p. This test method describes a procedure for determining the amount of volatile matter of any kind that is driven off from a test specimen under a specific set of temperature and time...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published January 2005. Originally approved in 1997. Last previous edition approved in 2004 as E 1886 – 04a. 8 p. This test method covers the performance of exterior windows, curtain walls, doors, and impact protective systems impacted by missile(s) and subsequently subjected to cyclic static...
American Society for Testing and Materials (ASTM). 1997, 9 pages.
This test method covers guidelines for acoustic emission (AE) tests of pressurized containers made of fiberglass reinforced
plastic (FRP) with balsa cores. Containers of this type are commonly used on tank trailers for the transport of hazardous chemicals.
American Society for Testing and Materials (ASTM). 1997, 3 pages.
These test methods cover procedures for measuring and compensating for transmittance when using an infrared imaging
radiometer to measure the temperature of a specimen through an attenuating medium, such as a window, filter or atmosphere
American Society for Testing and Materials (ASTM). 1997, 7 pages.
This guide covers procedures for the contact ultrasonic examination of bulk materials or parts by transmitting pulsed
ultrasonic waves into the material and observing the indications of reflected waves. This guide covers only examinations
in which one search unit is used as both transmitter and receiver...
Publisher: ASTM Publish Date: 2014 Pages: 4 Language: English Format: PDF Size: 151 kB Scope 1.1 This test method covers a guided bend test for the determination of soundness and ductility of welds in ferrous and nonferrous products. Flaws, not shown by X rays, may appear in the surface of a specimen when it is subjected to progressive localized overstressing. This guided bend...
American Society for Testing and Materials (ASTM). Current edition approved June 15, 2011. Published July 2011. Originally approved in 1997. Last previous edition approved in 2002 as E1903 – 97 (2002). 21 p. This practice covers a process for conducting a Phase II environmental site assessment (ESA) of a parcel of property with respect to the presence or the likely presence of...
American Society for Testing and Materials (ASTM). 1995, 3 pages.
These reference radiographs illustrate various types and degrees of discontinuities occurring in thin-wall steel investment castings. They are intended to provide the following:
A guide enabling recognition of thin-wall steel casting discontinuities and their differentiation both as to type and degree through...
Publisher: ASTM Publish Date: 2003 (Reaffirmed 2014) Pages: 5 Language: English Format: PDF Size: 91 kB Scope 1.1 This guide covers recommendations for sectioning, cleaning, mounting, grinding, and polishing to reveal the microstructural features of thermal sprayed coatings (TSCs) and the substrates to which they are applied when examined microscopically. Because of the...
American Society for Testing and Materials (ASTM). 1997, 12 pages.
This test method covers guidelines for acoustic emission (AE) examinations of new and in-service aboveground storage
tanks of the type used for storage of liquids. This test method will detect acoustic emission in areas of sensor coverage that are stressed during the course of the test. For flat-bottom tanks...
American Society for Testing and Materials (ASTM). 1997, 13 pages.
Purpose—This guide covers a tutorial introduction to familiarize the reader with the operational capabilities and
limitations inherent in X-ray Compton Scatter Tomography (CST). Also included is a brief description of the physics and
typical hardware configuration for CST.
American Society for Testing and Materials (ASTM). 1997, 4 pages.
This guide covers techniques for conducting acoustic emission (AE) examinations of small parts. It is confined to test
objects (or defined regions of larger objects) where there is low AE signal attenuation throughout the test region. This eliminates
the consideration of complex attenuation factor corrections and...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2009. Published May 2009. Originally approved in 1999. Last previous edition approved in 2008 as E1996 – 08. 13 p. This specification covers exterior windows, glazed curtain walls, doors, and impact protective systems used in buildings located in geographic regions that are prone to hurricanes....
Publisher: ASTM Publish Date: 2011 Pages: 8 Language: English Format: PDF Size: 121 kB Scope This guide outlines the basic safety guidelines to be used in a metallographic laboratory. Safe working habits are discussed for various tasks performed in a metallographic laboratory.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2006. Published December 2006. 29 р. This specification covers industrial woven wire fabric, referred to as wire cloth, for general use including the separation of particles. Wire cloth can be made of any primary metal or metal alloy wire that is suitable for weaving. This specification does not...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2008. Published July 2008. Originally approved in 1999. Last previous edition approved in 2001 as E2018 – 01. 25 p. The purpose of this guide is to define good commercial and customary practice in the United States of America for conducting a baseline property condition assessment (PCA) of the...
This test method is intended as a general guide for the application of the volumetric Karl Fischer (KF) titration for determining free water and water of hydration in most solid or liquid organic and inorganic compounds. This test method is designed for use with automatic titration systems capable of determining the KF titration end point amperometrically. This test method is...
This test method covers the temperature calibration of dielectric analyzers over the temperature range from –100 to 300°C and is applicable to commercial and custom-built apparatus. The calibration is performed by observing the melting transition of standard reference materials having known transition temperatures within the temperature range of use.
This test method describes the gathering and reporting of dynamic dielectric data. It incorporates laboratory test method for determining dynamic dielectric properties of specimens subjected to an oscillatory electric field using a variety of dielectric sensor/cell configurations on a variety of instruments called dielectric, microdielectric, DETA (DiElectric Thermal Analysis), or...
Publisher: ASTM Publish Date: 2009 Pages: 8 Language: English Format: PDF Size: 122 kB Scope 1.1 These test methods cover procedure and equipment for the determination of tensile strength, yield strength, elongation, and reduction of area of metallic materials at elevated temperatures. 1.2 Determination of modulus of elasticity and proportional limit are not included. 1.3...
Scope - These test methods cover procedure and equipment for the determination of tensile strength, yield strength, elongation, and reduction of area of metallic materials at elevated temperatures. Current edition approved Dec. 1, 2017. Published January 2018. Originally approved in 1933. Last previous edition approved in 2009 as E21-09. DOI: 10.1520/E0021-17E01.
American Society for Testing and Materials (ASTM). 1998, 5 pages.
This practice covers a procedure for detecting discontinuities in metal pipe and tubing using pulse-reflection ultrasonic contact or immersion angle beam techniques. Artificial discontinuities consisting of longitudinal reference notches are employed as the primary means of standardizing the ultrasonic
system. If...
American Society for Testing and Materials (ASTM). Reapproved 1996. 3 pages.
This practice describes in general terms an ultrasonic test procedure for detecting discontinuities in material using testing instruments which have been designed to transmit and receive pulsed longitudinal ultrasonic waves introduced into the material to be inspected through a liquid coupling agent.
American Society for Testing and Materials (ASTM). 1998, 7 pages.
This practice is intended as a guide for standardizing eddy-current equipment employed in the examination of seamless aluminum-alloy tube. Artificial discontinuities consisting of flat-bottomed or through holes, or both, are employed as the means of standardizing the eddy-current system. General requirements for...
American Society for Testing and Materials (ASTM). Current edition approved April 10, 2002. Published July 2002. 2 р. This terminology standard includes terms that relate to
the examination performed by forensic document examiners
Publisher: ASTM Publish Date: 2013 Pages: 6 Language: English Format: PDF Size: 143 kB Scope 1.1 This test method describes notched-bar impact testing of metallic materials using Miniaturized Charpy V-Notch (MCVN) specimens and test apparatus. It provides: (a) a description of the apparatus, (b) requirements for inspection and calibration, (c) safety precautions, (d) sampling,...
Publisher: ASTM
Publish Date: 2015
Pages: 9
Language: English
Format: PDF
Document Scope
1.1 This test method establishes the requirements for performing
instrumented Charpy V-Notch (CVN) and instrumented
Miniaturized Charpy V-Notch (MCVN) impact tests on
metallic materials. This method, which is based on experience
developed testing steels, provides further...
Publisher: ASTM Publish Date: 2012 Pages: 25 Language: English Format: PDF Size: 722 kB Scope 1.1 These test methods describe notched-bar impact testing of metallic materials by the Charpy (simple-beam) test and the Izod (cantilever-beam) test. They give the requirements for: test specimens, test procedures, test reports, test machines (see Annex A1) verifying Charpy impact...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. 4 p. This test method covers measurement of the daytime chromaticity coordinates (x, y) of horizontal pavement markings, such as traffic stripes and surface symbols, and pavement surfaces under diffuse illumination, using a portable reflection colorimeter that can be...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. 4 p. This test method covers measurement of the nighttime chromaticity coordinates (x, y) of horizontal pavement markings, such as traffic stripes and surface symbols, using a portable retroreflection colorimeter that can be placed on the road delineation to measure...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published February 2005. 14 p. This practice describes procedures for determining the amount and angular distribution of optical scatter from a surface. In particular it focuses on measurement of the bidirectional scattering distribution function (BSDF). BSDF is a convenient and well accepted...
American Society for Testing and Materials (ASTM). 1995, 3 pages.
This document describes the appearance of a radiographic image where fundamental components of image quality are changed, that is, variables such as whether a X-ray or gamma ray source was used, the characteristics of the radiographic film and intensifying screens, and the geometrical
configuration of the object...
American Society for Testing and Materials (ASTM). 1997, 6 pages.
This practice2 covers the procedures that shall be followed in eddy-current examination of copper and copperalloy tubes for detecting discontinuities of a severity likely to cause failure of the tube. These procedures are applicable for tubes with outside diameters to 31⁄8 in. (79.4 mm), inclusive,
and wall...
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2008. Published August 2008. 18 p. This guide describes procedures for evaluating some performance characteristics of phased-array ultrasonic examination instruments and systems. Evaluation of these characteristics is intended to be used for comparing instruments and systems or, by periodic...
American Society for Testing and Materials (ASTM). Current edition approved Julu 1, 2007. Published July 2007. 1 p. This practice describes a procedure for detecting subsurface flaws in composite panels and repair patches using Flash Thermography (FT), in which an infrared (IR) camera is used to detect anomalous cooling behavior of a sample surface after it has been heated with...
American Society for Testing and Materials (ASTM). 1999. 4 pages.
These reference radiographs illustrate various types and degrees of discontinuities occurring in high-strength copperbase, nickel-copper, and related types of alloys
American Society for Testing and Materials (ASTM). 1993, 3 pages.
This practice describes general ultrasonic test procedures for the detection of discontinuities in the weld and adjacent heat affected zones of pipe and tubing. It is intended for tubular products having diameters $2 in. ($50 mm) and wall thicknesses of 1⁄8 to 11⁄16 in. (3 to 27 mm).
American Society for Testing and Materials (ASTM). 1998, 3 pages.
These reference radiographs2 .for heavy-walled steel castings are applicable to nominal section thicknesses of 41⁄2 to 12 in. (114 to 305 mm)
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2011. Published June 2011. 5 p. This test method applies to measuring plate deflections using a Portable Impulse Plate Load Test device. The method covers the measurement of deflection of the load plate rather than the deflection of the surface of the pavement or foundation layers (see Note 1).
American Society for Testing and Materials (ASTM). Current edition approved June 15, 2005. Published June 2005. Originally approved in 1966. Last previous edition approved in 2005 as E 284 – 05. 22 p. This terminology standard defines terms used in the description of appearance, including but not limited to color, gloss, opacity, scattering, texture, and visibility of both...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2008. Published October 2008. Originally approved in 1940. Last previous edition approved in 2006 as E 29 – 06b. 5 p. This practice is intended to assist the various technical committees in the use of uniform methods of indicating the number of digits which are to be considered significant in...
Publisher: ASTM Publish Date: 2014 Pages: 10 Language: English Format: PDF Size: 311 kB Scope 1.1 These test methods cover bend testing for ductility of materials. Included in the procedures are four conditions of constraint on the bent portion of the specimen; a guided-bend test using a mandrel or plunger of defined dimensions to force the mid-length of the specimen between...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2011. Published June 2011. 12 p. The primary objective of metallographic examinations is to reveal the constituents and structure of metals and their alloys by means of a light optical or scanning electron microscope. In special cases, the objective of the examination may require the development of...
American Society for Testing and Materials (ASTM). 1995, 5 pages.
This practice covers a procedure for applying the eddy-current method to detect discontinuities in ferromagnetic pipe and tubing (Note 1) where the article being examined is rendered substantially non-magnetic by the application of a concentrated, strong magnetic field in the region adjacent to the examining coil.
American Society for Testing and Materials (ASTM). 1999, 4 pages.
These reference radiographs are reproductions of original radiographs and illustrate various types and degrees of discontinuities occurring in tin bronze and related types of alloys
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published October 2005. Originally approved in 1967. Last previous edition approved in 2000 as E 313 – 00. 6 p. This practice provides numbers that correlate with visual ratings of yellowness or whiteness of white and nearwhite or colorless object-color specimens, viewed in daylight by an...
American Society for Testing and Materials (ASTM). 1994, 12 pages.
This practice describes procedures for evaluating the following performance characteristics of ultrasonic pulse-echo testing systems: Horizontal Limit and Linearity; Vertical Limit and Linearity; Resolution-Entry Surface and Far Surface; Sensitivity and Noise; Accuracy of Calibrated Gain Controls.
Relevant...
American Society for Testing and Materials (ASTM). Current edition approved July 15, 2005. Published August 2005. Originally approved in 1967. Last previous edition approved in 2005 as E 329 – 05. 9 p. This specification defines the minimum requirements for inspection agency personnel or testing agency laboratory personnel, or both, and the minimum technical requirements for...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2005. Published April 2005. Originally approved in 1971. Last previous edition approved in 2005 as E 336 – 05. 11 p. The sound isolation between two spaces in a building is determined by a combination of the direct transmission through the nominally separating building element (as normally...
Publisher: ASTM Publish Date: 2015 Pages: 11 Language: English Format: PDF Size: 118 kB Scope 1.1 These procedures describe the methods of macroetching metals and alloys to reveal their macrostructure. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for...
American Society for Testing and Materials (ASTM). 1996, 4 pages.
This practice covers the use of magnetic- and eddycurrent type thickness instruments (gages) for nondestructive thickness measurement of a coating on a metal substrate
Publisher: ASTM
Publish Date: 2011
Pages: 43
Language: English
Format: PDF
Size: 740 kB
Scope
1.1 This test method covers determination of the Knoop and
Vickers hardness of materials, the verification of Knoop and
Vickers hardness testing machines, and the calibration of
standardized Knoop and Vickers test blocks.
1.2 This test method covers Knoop and Vickers...
American Society for Testing and Materials (ASTM). 1995, 4 pages.
This standard provides reference radiographs for steel fusion welds that contain typical discontinuities with varying severity levels in different thicknesses of material.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2012. Published January 2013. Originally approved in 1970. Last previous edition approved in 2009 as E399 – 09. 33 p. This test method covers the determination of fracture toughness (KIc) of metallic materials under predominantly linear-elastic, plane-strain conditions using fatigue precracked...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. Published May 2007. 22 p. This practice covers chemical solutions and procedures to be used in etching metals and alloys for microscopic examination. Safety precautions and miscellaneous information are also included. This standard does not purport to address all of the safety concerns, if...
Publisher: ASTM Publish Date: 2014 Pages: 10 Language: English Format: PDF Size: 132 kB Scope 1.1 These practices cover procedures for the force verification, by means of standard calibration devices, of tension or compression, or both, static or quasi-static testing machines (which may, or may not, have force-indicating systems). These practices are not intended to be complete...
American Society for Testing and Materials (ASTM). 1998, 4 pages.
This practice2 covers procedures that may be followed for eddy-current examination of seamless and welded tubular products made of stainless steel and similar alloys such as nickel alloys. Austenitic chromium-nickel stainless steels, which are generally considered to be nonmagnetic, are specifically covered as...
American Society for Testing and Materials (ASTM). 1995, 7 pages.
This practice covers procedures for testing and locating the sources of gas leaking at the rate of 2.2 3 10−14 mol/s (5 3 10−10 Std cm3/s).2 The test may be conducted on any device or component across which a pressure differential of halogen tracer gas may be created, and on which the effluent side of the area to...
American Society for Testing and Materials (ASTM). 1992, 6 pages.
This practice covers a procedure for fabrication and control of metal-alloy standard reference blocks used in ultrasonic inspection that contain flat-bottom holes (FBH) which may be used for checking performance of ultrasonic inspection instrumentation and search units and for standardization
and control of...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2005. Published July 2005. Originally approved in 1971. Last previous edition approved in 2003 as E 430 – 97 (2003). 6 p. These test methods cover the measurement of the reflection characteristics responsible for the glossy appearance of high-gloss surfaces. Two test methods, A and B, are provided...
American Society for Testing and Materials (ASTM). 1996, 7 pages.
This guide provides illustrations of radiographs of semiconductors and related devices. Low powered transistors (through the TO-11 case configuration), diodes, low-power rectifiers, power devices, and integrated circuits are illustrated with common assembly features. Particular areas of construction are featured...
American Society for Testing and Materials (ASTM). 1997, 3 pages. This guide2 is intended to assist in the selection of a leak testing method.3 Fig. 1 is supplied as a simplified guide. The type of item to be tested or the test system and the method considered for either leak measurement or location are related in the order of increasing sensitivity
American Society for Testing and Materials, 1991. - 3 pp. Настоящий стандарт относится к области поиска течей в вакуумной технике. В стандарте содержится классификация методов течеискания и руководство по выбору метода. This guide is intended to assist in the selection of a leak testing method. Scope. Referenced Document. Terminology. Selection of System. Leakage Measurement....
American Society for Testing and Materials (ASTM). 1997, 5 pages.
These reference photographs are supplied as a means of establishing types and characteristics of surface discontinuities detectable by the penetrant inspection methods. They may be used as a reference for acceptance standards, specifications and drawings
American Society for Testing and Materials (ASTM). 1998, 3 pages.
These reference radiographs2 illustrate various types and degrees of discontinuities occurring in steel castings that have section thicknesses up to 2 in. (51 mm).
Американское общество материалов и контроля (ASTM). Перевод на русский язык. Настоящее издание было утверждено 1 ноября 2005 г. Опубликовано в декабре 2005 г. 4 стр. Данные методы испытания охватывают целый ряд признанных методик для определения содержания неметаллических включений в деформируемой стали. Макроскопические методы включают испытания макротравлением, разрушением,...
American Society for Testing and Materials (ASTM). 1996, 5 pages.
This standard is intended as a guide. It enumerates factors to be considered in preparing a definitive specification for maximum permissible gas leakage of a component, device, or system. The guide relates and provides examples of data for the preparation of leak testing specifications. It is primarily applicable...
American Society for Testing and Materials (ASTM). 1997, 3 pages.
These test methods cover procedures for testing devices that are sealed prior to testing, such as semiconductors, hermetically enclosed relays, pyrotechnic devices, etc., for leakage through the walls of the enclosure. They may be used with various degrees of sensitivity (depending on the internal volume, the...
American Society for Testing and Materials (ASTM). 1995, 13 pages.
This practice covers a test procedure for measuring ultrasonic velocities in materials with conventional ultrasonic pulse echo flaw detection equipment in which results are displayed in an A-scan display. This practice describes a method whereby unknown ultrasonic velocities in a material
sample are determined by...
American Society for Testing and Materials (ASTM). 1995, 4 pages.
These test methods cover procedures for testing and locating the sources of gas leaking at the rate of 4.5 3 10−14 mol/s (1 3 10−9 Std cm3/s)3 or greater. The test may be conducted on any object to be tested that can be evacuated and to the other side of which helium or other tracer gas may be applied.
American Society for Testing and Materials (ASTM). 1995, 6 pages.
These test methods cover procedures for testing and locating the sources of gas leaking at the rate of 4.5 3 10−13 mol/s (1 3 10−8 Std cm3/s)3 or greater. The test may be conducted on any device or component across which a pressure differential of helium or other suitable tracer gas may be created, and on which the...
American Society for Testing and Materials (ASTM). 1996, 3 pages.
These reference radiographs illustrate the categories and severity levels of discontinuities that may occur in aluminumalloy and magnesium-alloy die castings
American Society for Testing and Materials (ASTM). 2000, 3 pages.
This test method covers procedures for detecting or locating leaks, or both, by bubble emission techniques. A quantitative measure is not practical. The normal limit of sensitivity for this test method is 4.5 3 10−10 mol/s (1 3 10 −5 Std cm3/s).2
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published October 2007. Originally approved in 1974. Last previous edition approved in 2003 as E 527–83 (2003). 7 p. This practice (Note 1) covers a unified numbering system (UNS) for metals and alloys that have a “commercial standing” (see Note 2), and covers the procedure by which such...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2004. Published April 2004. 3 p. This guide covers the flexural testing of beams and girders under simulated service conditions to determine their structural performance characteristics. Methods following this guide are intended primarily for constructions that may not conform with the relatively...
American Society for Testing and Materials (ASTM). 1999, 10 pages.
This practice covers minimum requirements for agencies performing nondestructive testing (NDT).
When using this practice to assess the capability of, or to accredit NDT agencies, Guide E 1359 shall be used as a basis for the survey. It can be supplemented as necessary with more detail in order to meet the...
American Society for Testing and Materials (ASTM). 1999, 4 pages. This test method covers the use of an Image Quality Indicator (IQI) system to determine the relative2 quality of radiographic images produced by direct, thermal neutron radiographic examination. The requirements expressed in this test method are not intended to control the quality level of materials and components.
American Society for Testing and Materials (ASTM). Current edition approved September 10, 2000. Published July 2001. 6 р. This guide describes options of intructions recommended to be considered in preparation for, and application and installation of, operable partitions and, to some extent, in the design of the building in which they are installed. Operable partitions are those...
American Society for Testing and Materials (ASTM). 1999, 5 pages.
This practice covers the procedure for sorting ferrous metals using the electromagnetic (eddy-current) method. The procedure relates to instruments using absolute or comparator type coils for distinguishing variations in mass, shape, conductivity, permeability, and other variables such as hardness and alloy that...
American Society for Testing and Materials (ASTM). 1997, 4 pages.
This practice provides guidelines for acoustic emission (AE) examination or monitoring of structures, such as pressure vessels, piping systems, or other structures that can be stressed by mechanical or thermal means.
American Society for Testing and Materials (ASTM). 1997, 6 pages.
This practice covers the application and calibration of equipment using the flux leakage test method for detection of outer surface, inner surface, and subsurface discontinuities in
ferromagnetic steel tubular products (Note 1) of uniform cross section such as seamless and welded tubing.
American Society for Testing and Materials (ASTM). 1998, 4 pages.
This practice covers the procedures for eddy-current testing of nickel and nickel alloy tubes. These procedures are applicable for tubes with outside diameters up to 2 in. (50.8mm), incl, and wall thicknesses from 0.035 to 0.120 in. (0.889 to 3.04 mm), incl. These procedures may be used for tubes beyond the size...
American Society for Testing and Materials (ASTM). 2000, 8 pages.
This practice covers ultrasonic examination of materials by the pulse-echo technique, using continuous coupling of angular incident ultrasonic vibrations
American Society for Testing and Materials (ASTM). 1999, 5 pages.
This guide to obtainable equivalent penetrameter sensitivity covers the minimum penetrameter thicknesses for which the image of the 1T and 2T holes is visible for a few practical radiographic conditions. The values represent near optimum sensitivity for flat steel plates. Radiographic conditions that give higher...
Publisher: ASTM Publish Date: 2014 Pages: 12 Language: English Format: PDF Size: 162 kB Scope 1.1 This terminology covers the principal terms relating to methods of mechanical testing of solids. The general definitions are restricted and interpreted, when necessary, to make them particularly applicable and practicable for use in standards requiring or relating to mechanical...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. Published May 2007. Originally approved in 1977. Last previous edition approved in 2001 as E 618 – 81 (2001). 11 p. This test method covers a production-type test for evaluating the machining performance of ferrous metals as they are used in single-spindle or multiple-spindle automatic screw...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 15, 2013. Published February 2014. Originally approved in 1978. Last previous approved in 2013 as E647 – 13. 50 p. This test method covers the determination of fatigue crack growth rates from near-threshold to Kmax controlled instability. Results are expressed in terms of the crack-tip...
American Society for Testing and Materials (ASTM). 1997, 3 pages.
This document provides guidelines for mounting piezoelectric acoustic emission (AE) sensors
American Society for Testing and Materials (ASTM). Reapproved 2000, 3 pages.
This practice describes a procedure for measuring the apparent attenuation of ultrasound in materials or components with flat, parallel surfaces using conventional pulse-echo ultrasonic flaw detection equipment in which reflected indications are displayed in an A-scan presentation
American Society for Testing and Materials (ASTM). Reapproved 1999, 2 pages. These reference radiographs extend the application of reference radiographs for steel castings to ductile iron castings
American Society for Testing and Materials (ASTM). 1998, 4 pages.
This practice describes procedures to be followed during eddy-current examination (using an internal, probe-type, coil assembly) of nonmagnetic tubing that has been installed in a heat exchanger. The procedure recognizes both the unique problems of implementing an eddy-current examination of installed tubing, and...
ASTM E 7 M Standard Terminology Relating to Metallography
Significance and Use
Standards of Committee E-4 consist of test methods, practices, and guides developed to ensure proper and uniform testing in the field of metallography. In order for one to properly use and interpret these standards, the terminology used in these standards must be understood.
The terms used in...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2009. Published March 2010. 33 p. This standard covers the definition of terms, acronyms, and symbols used in ASTM documents related to the field of metallography and metallographic testing. Terms that are only relevant to a particular standard or that are adequately defined in a general dictionary...
American Society for Testing and Materials (ASTM). 1998, 5 pages.
This practice describes a procedure for sorting nonferrous metals using the electromagnetic (eddy-current) method. The procedure is intended for use with instruments using absolute or comparator-type coils for distinguishing variations in mass, shape, conductivity, and other variables such as alloy, heat treatment,...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 15, 2008. Published April 2008. 41 p. This guide describes techniques for both dry and wet magnetic particle testing, a nondestructive method for detecting cracks and other discontinuities at or near the surface in ferromagnetic materials. Magnetic particle testing may be applied to raw material,...
Approved: March 1, 2014
Published: April 2014
Number of Pages: 47
This guide covers techniques for both dry and wet magnetic particle testing, a nondestructive method for detecting cracks and other discontinuities at or near the surface in ferromagnetic materials. Magnetic particle testing may be applied to raw material, semifinished material (billets, blooms, castings, and...
American Society for Testing and Materials (ASTM). 1995, 34 pages.
This guide describes techniques for both dry and wet magnetic particle examination, a nondestructive method for detecting cracks and other discontinuities at or near the surface
in ferromagnetic materials. Magnetic particle examination may be applied to raw material, semifinished material (billets, blooms,...
Publisher: ASTM Publish Date: 2015 Pages: 33 Language: English Format: PDF Size: 265 kB Scope 1.1 This standard covers the definition of terms, acronyms, and symbols used in ASTM documents related to the field of metallography and metallographic testing. Terms that are only relevant to a particular standard or that are adequately defined in a general dictionary are not defined...
American Society for Testing and Materials (ASTM). Reapproved 1998, 5 pages.
This test method covers the determination of the relative image quality response of industrial radiographic film when exposed to 200-kV X rays. The evaluation of the film is based
upon the threshold visibility of penetrameter holes in a special image quality indicator (IQI). Results for a given film...
American Society for Testing and Materials (ASTM). 1997, 14 pages.
This practice2 covers the design, material grouping classification, and manufacture of wire image quality indicators (IQI) used to indicate the quality of radiologic images
American Society for Testing and Materials (ASTM). 1995, 11 pages.
Purpose—Practices to be employed for the radiographic examination of materials and components with thermal neutrons are outlined herein. They are intended as a guide for the production of neutron radiographs that possess consistent quality characteristics, as well as aiding the user to consider the applicability...
American Society for Testing and Materials (ASTM). 1996, 5 pages.
This practice provides recommended guidelines for acoustic emission (AE) monitoring of weldments during and immediately following their fabrication by continuous welding processes. The technique is in a developmental stage and is not used routinely on production welding. Depending on the
results of ongoing...
American Society for Testing and Materials (ASTM). 1998, 9 pages.
This practice is recommended for use in testing and measuring operating characteristics of acoustic emission electronic components or units. (See Appendix X1 for a description of components and units.) It is not intended that this practice be used for routine checks of acoustic emission instrumentation, but rather...
American Society for Testing and Materials (ASTM). 1996, 6 pages.
This practice describes procedures for the measurement, processing, and interpretation of the acoustic emission (AE) response associated with selected stages of the resistance spot-welding process.
American Society for Testing and Materials (ASTM). 1995, 7 pages.
This practice2 provides guidelines for measuring the thickness of materials using the contact pulse-echo method at temperatures not to exceed 200°F (93°C).
This practice is applicable to any material in which ultrasonic waves will propagate at a constant velocity throughout the part, and from which back...
American Society for Testing and Materials (ASTM). Current edition approved Dec. 1, 2009. Published December 2009. 27 p. These test methods cover the tension testing of metallic materials in any form at room temperature, specifically, the methods of determination of yield strength, yield point elongation, tensile strength, elongation, and reduction of area. The gage lengths for...
ASTM, 2011. — 27 p, E8/E8M Standard Test Methods for Tension Testing of Metallic Materials These test methods cover the tension testing of metallic materials in any form at room temperature, specifically, the methods of determination of yield strength, yield point elongation, tensile strength, elongation, and reduction of area. The gage lengths for most round specimens are...
[/URL][/img]
Publisher: ASTM
Publish Date: 2015
Pages: 29
Language: English
ISBN: N/A
These test methods cover the tension testing of metallic materials in any form at room temperature, specifically, the methods of determination of yield strength, yield point elongation, tensile strength, elongation, and reduction of area.
American Society for Testing and Materials (ASTM). Reapproved 1995, 4 pages.
This practice relates to the radiological examination of electronic devices for internal discontinuities, extraneous material, missing components, crimped or broken wires, and defective solder joints in cavities, in the encapsulating materials, or the boards. Requirements expressed in this practice are...
American Society for Testing and Materials (ASTM). Reapproved 1999, 2 pages.
These reference radiographs for gray iron castings consist of one set of illustrations of centerline shrinkage with severity levels 1 to 5 using three radiation source types
США ASTM International Актуальный стандарт 2016 год Стандартные термины, касающиеся систем автомобильных покрытий. Необходимый стандарт для испытаний шин и автотранспорта Standard Terminology Relating to Vehicle-Pavement Systems
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2009. Published August 2009. 15 р. This test method covers the laboratory measurement of airborne sound transmission loss of building partitions such as walls of all kinds, operable partitions, floor-ceiling assemblies, doors, windows, roofs, panels, and other space-dividing elements....
American Society for Testing and Materials (ASTM). 1998, 6 pages.
This practice covers procedures for calibrating leak artifacts of a specified gas, that may be used for determining the response of leak detectors, or in other situations where a known small flow of gas is required. The purpose of this practice is to establish calibration without reference to other
calibrated...
Publisher: ASTM Publish Date: 2009 Pages: 9 Language: English Format: PDF Size: 500 kB Scope 1.1 These test methods cover the apparatus, specimens, and procedure for axial-load compression testing of metallic materials at room temperature (Note 1). For additional requirements pertaining to cemented carbides, see Annex A1. NOTE 1—For compression tests at elevated temperatures,...
American Society for Testing and Materials (ASTM). 2000, 12 pages.
This guide2 covers satisfactory X-ray and gamma-ray
radiographic examination as applied to industrial radiographic
film recording. It includes statements about preferred practice
without discussing the technical background which justifies the
preference. A bibliography of several textbooks and standard...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2010. Published February 2011. Originally approved in 1953. Last previous edition approved in 2000 as E96 – 00. 12 p. These test methods cover the determination of water vapor transmission (WVT) of materials through which the passage of water vapor may be of importance, such as paper, plastic...
США ASTM International Актуальный стандарт 2016 год ASTM E965 – 15 - Стандартный метод испытаний для измерения глубины макротекстуры дорожного покрытия с использованием волюметрического метода" (песчаного пятна) – действующий стандарт. Включает в себя: ASTM E965 - 96(2006) - Стандартный метод испытаний для измерения глубины макротекстуры дорожного покрытия с использованием...
American Society for Testing and Materials (ASTM). 1999, 9 pages.
This guide defines simple economical procedures for testing or comparing the performance of acoustic emission sensors. These procedures allow the user to check for degradation
of a sensor or to select sets of sensors with nearly identical performances. The procedures are not capable of providing an absolute...
American Society for Testing and Materials (ASTM). Reapproved 1999, 3 pages.
This practice covers the procedure for sorting materials using the thermoelectric method, which is based on the Seebeck effect. The procedure relates to the use of direct- and comparator-type thermoelectric instruments for distinguishing variations in materials which affect the thermoelectric properties...
American Society for Testing and Materials (ASTM). 1999, 5 pages.
This guide2 establishes guidelines that may be used for the control and maintenance of industrial radiographic film processing equipment and materials. Effective use of these guidelines aid in controlling the consistency and quality of industrial radiographic film processing.
American Society for Testing and Materials - 2016.- 4 p. The purpose of the sample may be to estimate properties of a larger population, such as a lot, pile or shipment, the percentage of some constituent, the fraction of the items that fail to meet (or meet) a specified requirement, the average characteristic or quality of an item, the total weight of the shipment, or the...
Current edition approved Aug. 15, 2020. Published September 2020. Originally approved in 1993. Last previous edition approved in 2014 as E1237 – 93 (2014). This standard is issued under the fixed designation E l237; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in...
American Society for Testing and Materials. 2010.- 6 p. This guide applies to decommissioning plans for any nuclear facility whose operation was (is) governed by U.S. Nuclear Regulatory Commission (NRC) or Agreement State license, or under U.S. Department of Energy (DOE) orders. The guide applies to the preparation and content of the decommissioning plan document itself. The...
American Society for Testing and Materials - 2017.- 12 p. This terminology generally covers terms that apply to radiation measurements and dosimetry associated with energy deposition and radiation effects, or damage, in materials caused by interactions by high-energy radiation fields. The common radiation fields considered are X-rays, gamma rays, electrons, alpha particles,...
American Society for Testing and Materials - 2014.- 9 p. The purpose of this practice is to present concepts necessary to the understanding of the terms “precision” and “bias” as used in quantitative test methods. This practice also describes methods of expressing precision and bias and, in a final section, gives examples of how statements on precision and bias may be written...
American Society for Testing and Materials - 2016.- 11 p. This practice covers outlying observations in samples and how to test the statistical significance of them. An outlying observation, or outlier, is one that appears to deviate markedly from other members of the sample in which it occurs. In this connection, the following two alternatives are of interest: (i) an outlying...
American Society for Testing and Materials - 2017.- 21 p. These methods cover general procedures for the calibration of radiation detectors and the analysis of radionuclides. For each individual radionuclide, one or more of these methods may apply. These methods are concerned only with specific radionuclide measurements. The chemical and physical properties of the radionuclides...
American Society for Testing and Materials - 2008.- 28 p. This standard provides recommendations on the selection and use of portable instrumentation that is responsive to levels of radiation that are close to natural background. These instruments are employed to detect the presence of residual radioactivity that is at, or below, the criteria for release from further regulatory...
American Society for Testing and Materials - 2014.- 24 p. This guide is an organized collection of information and series of options for industry, regulators, auditors, consultants and the public, intended to measure compliance with environmental performance standards against established benchmarks. It focuses on compliance with air, water, waste prevention, waste management,...
ASTM, 2010. — 6 p. The purpose of this guide is to establish a framework and context for process understanding for pharmaceutical manufacturing using quality by design (QbD) (Juran, 1992;2 FDA/ICH Q8). The framework is applicable to both active pharmaceutical ingredient (API) and to drug product (DP) manufacturing. High (detailed) level process understanding can be used to...
ASTM, 2009. — 11 p. This document provides guidance on the implementation of risk assessment and risk control for Process Analytical Technology (PAT) processes within the pharmaceutical industry. Wherever possible, other appropriate standards on risk assessment/management have been referenced and acknowledged. Where practical, further details of methods and additional...
Current edition approved June 1, 2020. Published August 2020. Originally approved in 1964. Last previous edition approved in 2014 as E25I - 9 2 (2014). This standard is issuod under the fixed designation B25I; the number immediately following the designation indicates tho year of original adoption or, in the case of revision, the year of last revision. A number in parentheses...
ASTM International. — 20 p. Adopted January 15 1992. Reapproved April 15 2014. Superseded by ASTM E251-20a. This standard is issued under the fixed designation B25I; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A...
В документе описана методика определения размера зерна в полностью рекристаллизованном поликристаллическом материале методом дифракции отраженных электронов.
This practice is used to determine grain size from
measurements of grain areas from automated electron backscatter
diffraction (EBSD) scans of polycrystalline materials.
ASTM International, 2010. — 25 p. This guide presents terminology, concepts, and selected methods and formulas useful for measurement systems analysis (MSA). Measurement systems analysis may be broadly described as a body of theory and methodology that applies to the non-destructive measurement of the physical properties of manufactured objects.
ASTM International, 2011. — 26 p. This guide presents terminology, concepts, and selected methods and formulas useful for measurement systems analysis (MSA). Measurement systems analysis may be broadly described as a body of theory and methodology that applies to the non-destructive measurement of the physical properties of manufactured objects.
These test methods cover a number of recognized procedures for determining the nonmetallic inclusion content of wrought steel. Macroscopic methods include macroetch, fracture, step-down, and magnetic particle tests. Microscopic methods include five generally accepted systems of examination. In these microscopic methods, inclusions are assigned to a category based on similarities...
American Society for Testing and Materials. Reapproved edition, 2017.- 10 p. A term in this standard which lists an attribution to an E11 technical standard indicates that the standard is normative for that term. Any changes in the term definition in the normative standard will be editorially changed in this standard. Any terms added to an E11 standard will be editorially added...
Current edition approved June 1, 2013. Published September 2013. Originally approved in 1986. Last previous edition approved in 2007 as F1016 – 07. — 3 p. This practice describes the elementary linear regression analysis of basic treadwear data as obtained according to Test Method F421 and Test Method F762. The basic treadwear data are obtained as groove depth loss measurements by...
Current edition approved June 1, 2015. Published September 2015. Originally approved in 1986. Last previous edition approved in 2008 as F1035 – 03 (2008). — 4 p. This practice describes the construction and use of a rubber-cord pie-shaped standard disk for demonstrating the discernment capability of an X-ray imaging system. This practice is applicable to direct viewing...
Current edition approved April 1, 2011. Published May 2011. Originally approved in 1968. Last previous edition approved in 2009 as F104 – 03 (2009). — 12 p. This classification system2 provides a means for specifying or describing pertinent properties of commercial nonmetallic gasket materials. Materials composed of asbestos, cork, cellulose, and other organic or inorganic...
Current edition approved May 1, 2015. Published June 2015. Originally approved in 1987. Last previous edition approved in 2008 as F1046 – 01 (2008). — 4 p. This guide outlines the preparation of artificially worn tires by tread rubber removal (cutting or grinding, or both) for subsequent performance testing. The purpose is to permit the preparation of test tires with a uniformly...
Current edition approved Oct. 1, 2016. Published October 2016. Originally approved in 1988. Last previous edition approved in 2009 as F1087 – 02 (2009). — 2 p. This test method covers a procedure to determine the stability of a gasket material to linear dimensional change due to hygroscopic expansion and contraction. It subjects a sampleto extremes, that is, oven drying and...
Current edition approved Dec. 1, 2010. Published March 2011. Originally approved in 1987. Last previous edition approved in 2006 as F1112 – 06a. — 7 p. This test method covers the determination of the rate of inflation pressure loss resulting from air diffusion through thestructures of tubeless tires under constant temperature conditions. The testing is done under static...
Current edition approved May 1, 2013. Published May 2013. Originally approved in 1970. Last previous edition approved in 2006 as F112 – 00 (2006). — 4 p. This test method covers the evaluation of the sealing properties of enveloped gaskets for use with corrosion-resistant process equipment.2 Enveloped gaskets are described as gaskets having some corrosion-resistant covering over...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally
approved in 1988. Last previous edition approved in 2000 as F 1137-00. 2 p. This specification covers the basic requirements for seven grades of corrosion protection for fasteners. Grade 0A consists of a zinc phosphate coating with no additional sealer (dry),...
American Society for Testing and Materials (ASTM). Originally approved in 1988. Current edition approved Nov. 1, 2004. Published November 2004. 5p. This specification provides the minimum requirements for the design, fabrication, pressure rating, marking, and testing of steam traps and drains. The following safety hazards caveat pertains only to the test method portion of this...
Current edition approved July 1, 2013. Published August 2013. Originally approved in 1970. Last previous edition approved in 2012 as F118 – 04 (2012). — 3 p. This standard is a compilation of terminology, related definitions, and descriptions of terms used in the gasket industry. Included terms are those used to define materials, testing technology, and testing results related to...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2009. Published March 2009. 13 p. This practice describes the procedures for the reconstruction of pipelines and conduits (4 to 108-in. diameter) by the installation of a resin-impregnated, flexible tube which is inverted into the existing conduit by use of a hydrostatic head or air pressure. The...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2013. Published November 2013. Originally approved in 1989. Last previous edition approved in 2011 as F1249 – 06 (2011). 6 p. This test method covers a procedure for determining the rate of water vapor transmission through flexible barrier materials. The method is applicable to sheets and films up...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2006. Published October 2006. Originally approved in 1989. Last previous edition approved in 2001 as F 1267 – 01. 7 p. This specification covers expanded metal. Expanded metal covered by this specification is intended for a variety of applications. The values stated in inch-pound units are to be...
Current edition approved Oct. 1, 2016. Published October 2016. Originally approved in 1990. Last previous edition approved in 2009 as F1276 – 99 (2009). — 5 p. This test method provides a means of measuring the amount of creep relaxation of a laminated composite gasket material at a predetermined time after a compressive stress has been applied. Creep relaxation is measured by...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. 11p. This specification covers a coextruded crosslinked polyethylene composite pressure pipe with a welded aluminum tube reinforcement between the inner and outer layers. The inner and outer crosslinked polyethylene layers are bonded to the aluminum tube by a melt adhesive. Included is a...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2007. Published June 2007. Originally approved in 1990. Last previous edition approved in 2002 as F1307 – 02. 7 p. This test method covers a procedure for the determination of the steady-state rate of transmission of oxygen gas into packages. More specifically, the method is applicable to packages...
Current edition approved Feb. 1, 2017. Published February 2017. Originally approved in 1990. Last previous edition approved in 2014 as F1315 – 00 (2014). — 2 p. This test method covers a procedure for determining the density of a gasket material.
American Society for Testing and Materials (ASTM). 2008. 14p. This specification covers the chemical, mechanical, and metallurgical requirements for wrought annealed titanium-6aluminum-4vanadium ELI (extra low interstitial) alloy (R56401) to be used in the manufacture of surgical implants
Current edition approved June 1, 2015. Published September 2015. Originally approved in 1992. Last previous edition approved in 2010 as F1364 – 03 (2010). — 3 p. This practice describes the construction and use of a calibration device for demonstrating the anomaly detection capability of interferometric laser imaging nondestructive tire inspection system. A common practice within...
Current edition approved Nov. 1, 2011. Published November 2011. Originally approved in 1993. Last previous edition approved in 2003 as F1426 – 94 (2003). — 4 p. This practice provides the instructions and nomenclature to evaluate the wear features of the tread pattern on a tire for some intermediate state short of total wear out. A tire may be characterized by certain worn...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 1992. Last previous edition approved in 1999 as F 1428 – 92 (1999). 3 p. This specification covers the basic requirements for a corrosion-resistant coating consisting of an inorganic aluminum particle-filled basecoat and an organic or inorganic...
Current edition approved Oct. 1, 2016. Published October 2016. Originally approved in 1972. Last previous edition approved in 2009 as F145 – 72 (2009). — 3 p. This practice permits measurement of gasket compression resulting from bolt loading on a flat-face joint assembly at ambient conditions.
Current edition approved Aug. 1, 2012. Published September 2012. Originally approved in 1972. Last previous edition approved in 2004 as F146 – 04. — 5 p. These test methods cover the determination of the effect on physical properties of nonmetallic gasketing materials after immersion in test fluids. The types of materials covered are Type 1, Type 2, Type 3, and Type 7 as described...
Current edition approved May 1, 2017. Published July 2017. Originally approved in 1972. Last previous edition approved in 2009 as F147 – 87 (2009). — 2 p. This test method covers the determination of the flexibility of non-metallic gasket materials. It is designed for testing specimens cut from sheet goods or from the gasket in the finished form, as supplied for commercial use....
Current edition approved July 1, 2013. Published August 2013. Originally approved in 1972. Last previous edition approved in 2013 as F148 – 02 (2013). — 2 p. This test method covers three procedures for determination of the binder durability of cork-containing materials.
Current edition approved Jan. 1, 2016. Published February 2016. Originally approved in 1994. Last previous edition approved in 2010 as F1502 – 05 (2010). — 5 p. This test method covers methods for performing certain mechanical static measurements on tires. The term “static” implies that the tire is not rotating while measurements are being made.
American Society for Testing and Materials (ASTM). Current edition approved July 1, 2007. Published July 2007. Originally approved in 1994. Last previous edition approved in 2002 as F 1503 – 02. 4 p. This practice covers provision of a proper method for determining process capability for new or existing machine processes. It is recommended that available statistical software be...
Current edition approved May 1, 2017. Published July 2017. Originally approved in 1972. Last previous edition approved in 2009 as F152 – 95 (2009). — 3 p. These test methods cover the determination of tensile strength of certain nonmetallic gasketing materials at room temperature. The types of materials covered are those containing asbestos and other inorganic fibers (Type 1),...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published August 2007. Originally approved in 1994. Last previous edition approved in 2004 as F 1554 – 04. 9 p. This specification covers straight and bent, headed and headless, carbon, carbon boron, alloy, or high-strength lowalloy steel anchor bolts (also known as anchor rods). The anchor...
Current edition approved May 1, 2015. Published June 2015. Originally approved in 1994. Last previous edition approved in 2008 as F1572 – 08. — 10 p. These test methods cover the evaluation of tire performance on snow and ice surfaces utilizing passenger car or light truck vehicles. Since the tires are evaluated as part of a tire/vehicle system, the conclusions reached may not be...
Current edition approved May 1, 2017. Published July 2017. Originally approved in 1995. Last previous edition approved in 2009 as F1574 – 03a (2009). — 4 p. This test method covers the determination of compressive strength characteristics (crush-extrusion resistance) of gasket materials at elevated temperature.
Current edition approved May 1, 2013. Published June 2013. Originally approved in 1995. Last previous edition approved in 2003 as F1649 – 96 (2003) which was withdrawn January 2012 and reinstated in May 2013. — 13 p. These test methods cover the measurement of two types of ABS vehicle behavior that reflect differences in tire wet traction performance when the vehicle is fitted...
Current edition approved Jan. 1, 2014. Published February 2014. Originally approved in 1995. Last previous edition approved in 2005 as F1650 – 98 (2005). — 13 p. This practice covers the required procedures for examining sequential control tire data for any variation due to changing test conditions. Such variations may influence absolute and also comparative performance of...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2005. Published January 2006. Originally approved in 1995. Last previous edition approved in 2003 as F 1667 – 03. 41 p. This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1. Fasteners described in this specification are driven by hand tool, power...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published September 2007. Originally approved in 1997. Last previous edition approved in 2007 as F 1789 – 07a. 12 p. This terminology standard provides a compilation of definitions for terminology used for mechanical fasteners. Terms in this terminology are organized alphabetically. In...
Current edition approved Jan. 1, 2016. Published February 2016. Originally approved in 1997. Last previous edition approved in 2012 as F1805 – 12. — 14 p. This test method covers a procedure for measuring the driving traction of passenger car and light truck tires while traveling in a straight line on snow- or ice-covered surfaces. This test method utilizes a dedicated,...
Current edition approved June 1, 2014. Published September 2014. Originally approved in 1997. Last previous edition approved in 2008 as F1806 – 97 (2008). — 6 p. This practice presents some basic concepts for tire testing and a standard set of terms relating to the use ofreference tires frequently used for comprehensive tire testing programs. The tests may be conducted in a...
American Society for Testing and Materials (ASTM). Current edition approved Jan. 1, 2005. Published January 2005. Originally approved in 1998. Last previous approved in 2004 as F 1852–04a. 8 p. This specification covers two types of heat treated, steel, tension control bolt-nut-washer assemblies, also referred to as “sets.” These assemblies are capable of developing a minimum...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2006. Published April 2006. Originally approved in 1998. Last previous edition approved in 1998 as F 1908 - 98. 6 p. This guide provides recommended minimum requirements for various types of fences for residential swimming pools, hot tubs, and spas. The values stated in inch-pound units are to...
Current edition approved Aug. 1, 2012. Published November 2012. Originally approved in 1998. Last previous edition approved in 2004 as F1909– 98 (2004). — 5 p. This specification covers preformed open–cell sponge rubber gaskets of the following classes for use in new or reconditioned pails or drums. Class A - Non–Oil Resistant. Class B - Oil Resistant.
Current edition approved Jan. 1, 2014. Published February 2014. Originally approved in 1998. Last previous edition approved in 2005 as F1922 – 98 (2005). — 7 p. This test method covers comparative tire durability and treadwear. This test method covers commercially available, over the highway pneumatic tires, new and retreaded, both tube type and tubeless, for use on conventional...
Current edition approved Jan. 1, 2014. Published February 2014. Originally approved in 1998. Last previous edition approved in 2005 as F1923 – 98 (2005). — 3 p. This test method covers measurements for comparative tire strength and dimensional characteristics. This test method covers new and retreaded pneumatic tires, both tube and tubeless types, and flaps when applicable, for...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published August 2007. Originally approved in 1998. Last previous edition approved in 2004 as F1927 – 98 (2004). 6 p. This test method covers a procedure for determination of the rate of transmission of oxygen gas, at steady-state, at a given temperature and %RH level, through film, sheeting,...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2006. Published June 2006. Originally approved in 1998. Last previous edition approved in 2000 as F 1941 – 00. 10 p. This specification covers application, performance and dimensional requirements for electrodeposited coatings on threaded fasteners with unified inch screw threads. It specifies...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 2000. Last previous edition approved in 2000 as F 1941M – 00. 11 p. This specification covers application, performance and dimensional requirements for electrodeposited coatings on threaded fasteners with metric screw threads. It specifies coating...
Current edition approved May 1, 2012. Published July 2012. Originally approved in 1999. Last previous edition approved in 2005 as F1971 – 05. — 4 p. This test method covers the measurement of the electrical resistance between the wheel of a mounted and inflated tire-wheel assembly and a flat conducting surface in loaded contact with the tire. This test method specifies procedures...
American Society for Testing and Materials (ASTM). Current edition approved May 10, 2000. 16p. This specification covers the pipe materials and dimensions for producing non-reinforced extruded tee connections manufactured by mechanical forming processes. The term extruded tee connection applies to butt-weld or socket-weld connections. This specification refers to the forming...
American Society for Testing and Materials (ASTM). Current edition approved Nov 10, 2000. 5p. This specification applies to interconnections of surgical instruments used for drilling, tapping, driving, or placing of medical devices during surgery. The specifications given in this standard have been written to lessen the chance of accidental disengagement of surgical...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2005. Published November 2005. Originally approved in 2000. Last previous edition approved in 2000 as F 2063 – 00. 4 p. This specification covers the chemical, physical, mechanical, and metallurgical requirements for wrought nickeltitanium bar, flat rolled products, and tubing containing nominally...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2007. Published July 2007. Originally approved in 2001. Last previous edition approved in 2001 as F 2089 – 01. 14 p. This guide identifies the components of quality language interpretation services and establishes criteria for each component. These criteria define the minimum standard of quality...
ASTM 2001, 7p. F 2094 Standard Specification for Silicon Nitride Bearing Balls
Brief Summary
This specification covers the establishment of the basic quality, physical/mechanical property, and test requirements for silicon nitride balls Classes I, II, and III to be used for ball bearings and specialty ball applications. Silicon nitride balls should be produced from either...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2006. Published December 2006. Originally approved in 2001. Last previous edition approved in 2003 as F 2094 – 03a. 8 p. This specification covers the establishment of the basic quality, physical/mechanical property, and test requirements for silicon nitride balls Classes I, II, and III to be used...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2011. Published September 2011. Originally approved in 2002. Last previous edition approved in 2009 as F2170 - 09. 6 p. This test method covers the quantitative determination of percent relative humidity in concrete slabs for field or laboratory tests.
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2008. Published March 2008. Originally approved in 2002. Last previous edition approved in 2007 as F 2212 – 02 (2007). 14 p. This guide for characterizing collagen-containing biomaterials is intended to provide characteristics, properties, and test methods for use by producers, manufacturers, and...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2005. Published May 2005. Originally approved in 2002. Last previous edition approved in 2003 as F 2215 – 03. 35 p. This specification covers requirements for ferrous and nonferrous inch balls. The balls covered in this specification are intended for use in bearings, bearing applications, check...
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2006. Published July 2006. 46 p. This practice establishes criteria for the design of amusement rides, devices and major modifications to amusement rides and devices manufactured after the effective date of publication.
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2009. Published March 2009. Originally approved in 2003. Last previous edition approved in 2003 as F2298 - 03. 10 p. This test method covers the measurement of the moisture vapor transport and gas flow properties of fabrics, membranes, and membrane laminates used for protective materials. The...
Current edition approved July 1, 2014. Published December 2014. Originally approved in 2003. Last previous edition approved in 2009 as F2325 – 03 (2009). — 3 p. This classification covers a means for specifying Multi- Layer Steel (MLS) and other Metal Layer Gaskets for Transportation Applications by application and construction. These structures are composed of one or more steel...
Current edition approved Oct. 1, 2016. Published October 2016. Originally approved in 2005. Last previous edition approved in 2011 as F2378 – 05 (2011). — 6 p. This test method covers a means of evaluating the sealing properties of sheet, composite, and solid form-in-place gasket materials (see Classification F104 or F868) at room temperature, and may be used for fluid (gas or...
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. 17 p. These test methods measure the resistance of footwear to a variety of hazards that can potentially result in injury. These test methods may be used to test for compliance to minimum performance requirements in established safety standards
American Society for Testing and Materials (ASTM). Current edition approved March 1, 2005. Published March 2005. 9 р. This specification covers minimum requirements for the design, performance, testing, and classification of footwear designed to provide protection against a variety of workplace hazards that can potentially result in injury. The objective of this specification...
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2005. Published February 2005. 3 p. This practice covers the installation and preparation of the thick poured gypsum concrete underlayments over wood structural panel subfloors in commercial structures or over concrete floors in commercial structures and the preparation of the thick poured gypsum...
American Society for Testing and Materials (ASTM). Current edition approved June 1, 2005. Published July 2005. 6 р. This specification covers welded wire mesh fence fabric produced from steel wire or metallic-coated steel wire. The metallic-coated fabric may be polymer coated after fabrication.
American Society for Testing and Materials (ASTM). Current edition approved March 15, 2009. Published May 2009. 13 p. This practice covers information for manufacture, construction, operations and maintenance of aquatic play equipment and provides safety performance standards for various types of public aquatic play components and aquatic play composite structures.
Current edition approved May 1, 2010. Published June 2010. Originally approved in 2005. Last previous edition approved in 2005 as F2466 – 05. — 5 p. This practice covers a means to determine the percent silicone-producing volatiles present in heat-cured silicone rubber and room temperature-cured silicones (RTV). Silicone-producing volatiles contribute to fouling of oxygen sensor...
Current edition approved May 1, 2013. Published May 2013. Originally approved in 2005. Last previous edition approved in 2006 as F2467 – 06. — 2 p. This practice covers a standard means for measuring initial static sealing pressure in transportation applications. It uses a pressure-indicating film (PIF) that will record the maximum load imprint of the seal-to-flange interfaces....
США ASTM International Актуальный стандарт 2016 год ASTM F2493 - 14 - Стандартная спецификация для шин P225 / 60R16 97 Standard Specification for P225/60R16 97S Radial Standard Reference Test Tire
Current edition approved July 1, 2013. Published August 2013. Originally approved in 2005. Last previous edition approved in 2013 as F2523 – 07 (2013). — 7 p. This practice provides a means to determine the blowout resistance of a room-temperature vulcanized elastomer system (RTV) using a standard fixture.
Current edition approved May 1, 2013. Published May 2013. Originally approved in 2006. Last previous edition approved in 2006 as F2524 – 06. — 2 p. This practice covers the quantitative determination of the volatile matter evolved during the curing process of transportation applications.
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2006. Published June 2006. 11 p. This guide identifies factors relevant to the quality of language translation services for each phase of a translation project. The guide is intended for use by all stakeholders, with varying levels of knowledge in the field of translation. This guide is designed...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published August 2007. 16 p. This test method provides a range of vehicle impact conditions, designations, and penetration performance levels. This will allow an agency to select passive perimeter barriers and active entry point barriers appropriate for use at facilities with a defined...
Current edition approved June 1, 2015. Published July 2015. Originally approved in 2007. Last previous edition approved in 2007 as F2663 – 07a. — 11 p. This test method covers the static non-rolling laboratory method of determination of a tubeless tire’s resistance to bead unseating. The test requires the use of a standardized fixture and load machine. The test is conducted using...
In: Annual Book of ASTM Standards vol. 10.04 (Electronics I), West Honshohoken, PA: ASTM Intl., 2001. - 5 p. - Approved 1987, reapproved 1999.
These test methods cover techniques for determining the crystallographic orientation of a surface which is roughly parallel to a low-index atomic plane in single crystals used primarily for semiconductor devices. Two test methods are...
Current edition approved July 1, 2014. Published November 2014. Originally approved in 2008. Last previous edition approved in 2008 as F2716 – 08. — 6 p. This practice provides a means of comparing various nonmetallic flat gasket materials, Classification F104, in saturated steam service under controlled conditions. While the practice is designed primarily for flat gaskets, it...
Current edition approved Oct. 1, 2016. Published October 2016. Originally approved in 2010. Last previous edition approved in 2010 as F2779 – 10. — 8 p. This practice describes the procedure to identify equivalent test severity conditions between a 1.707-m diameter laboratory roadwheel surface and a flat or highway surface forcommercial radial truck-bus tires. Tire operational...
Current edition approved May 1, 2015. Published June 2015. Originally approved in 2009. Last previous edition approved in 2009 as F2803 – 09. — 6 p. This test method is performed to determine the amount of rotational slip occurring at the tire/wheel interface while under heavy longitudinal load conditions. This test method is suitable for research and development purposes where...
Current edition approved April 1, 2011. Published May 2011. Originally approved in 2010. Last previous edition approved in 2010 as F2837 – 10. — 5 p. This test method covers a means of measuring the hot compression properties of a gasket material by measuring its creep under a constant load at both room temperature and while increasing the temperature. Short term creep properties...
Current edition approved May 1, 2010. Published June 2010. — 6 p. This practice describes a method to laboratory age a new tire in an oven to produce changes in certain chemical and physical properties at the belt edges similar to those of tires in-service (see Appendix X1). This practice is a precursor to conducting an ASTM standard roadwheel test method for laboratory generation...
Current edition approved Oct. 1, 2016. Published October 2016. Originally approved in 2010. Last previous edition approved in 2010 as F2869 – 10. — 8 p. This practice describes the procedure to identify equivalent test severity conditions between a 1.707-m diameter laboratory roadwheel surface and a flat or highway surface for radial pneumatic light truck (LT) tires. Tire...
США ASTM International Актуальный стандарт 2016 год ASTM F2870 – 16 Стандартные спецификации для 315 / 70R22,5 154 / 150L - 1 стандарт на комплект шин Standard Specification for 315/70R22.5 154/150L Radial Truck Standard Reference Test Tire
США ASTM International Актуальный стандарт 2016 год Стандартные спецификации для 245 / 70R19.5 136 / 134M - 1 стандарт на комплект шин Standard Specification for 245/70R19.5 136/134M Radial Truck Standard Reference Test Tire
США ASTM International Актуальный стандарт 2016 год ASTM F2872 – 16 - Стандартная спецификация для 225 / 75R16C 116 / 114S M + S радиальная легкий грузовик Standard Specification for 225/75R16C 116/114S M+S Radial Light Truck Standard Reference Test Tire
In: Annual Book of ASTM Standards vol. 10.04 (Electronics I), West Honshohoken, PA: ASTM Intl., 2001.- 8 p. Approved 1991, reapproved 1997.
These test methods cover the measurement of minority carrier lifetime appropriate to carrier recombination processes in bulk specimens of extrinsic single-crystal germanium and silicon by measurement of photoconductivity decay after...
Current edition approved Nov. 15, 2013. Published January 2014. — 7 p. This standard describes a laboratory method to evaluate tires for their tendency to develop belt edge separation, via the use of a standard roadwheel (Practice F551/F551M). This evaluation is conducted on tires that have undergone accelerated laboratory aging as described in Practice F2838. The End-of-Test...
Current edition approved June 1, 2015. Published August 2015. — 7 p. This practice will establish criteria for determining loading constants that are referenced in the American Society of Mechanical Engineers (ASME) pressure vessel design(Boiler and Pressure Vessel Code, Section VIII, Divs. 1 and 2). These constants are specific to this design criterion for metallic,...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2011. Published June 2011. Originally approved in 1970 as F316 – 70. Last previous edition approved in 2003 as F316 – 03. 7 p. These test methods cover the determination of two of the pore size properties of membrane filters with maximum pore sizes from 0.1 to 15.0 μm. Test Method A presents a...
Current edition approved April 1, 2016. Published April 2016. Originally approved in 1971. Last previous edition approved in 2009 as F336 – 02 (2009). — 4 p. This practice covers the designs, sizes, classifications, and construction of enveloped gaskets for severe corrosive applications. The envelope serves as the corrosion resistant member of the composite gasket and is a...
Current edition approved Jan. 1, 2015. Published February 2015. Originally approved in 1951. Redesignated F36 in 1963. Last previous edition approved in 2009 as F36 – 99 (2009). — 4 p. This test method covers determination of the short-time compressibility and recovery at room temperature of sheetgasket materials, form-in-place gaskets, and in certain cases, gaskets cut from...
Current edition approved May 1, 2011. Published July 2011. Originally approved in 1973. Last previous edition approved in 2004 as F363 – 99 (2004). — 3 p. This test method covers the evaluation of gaskets under corrosive conditions at varying temperature and pressure levels. The test unit may be glass lined if the flanges are sufficiently plane (industry accepted), thus providing...
Current edition approved May 1, 2013. Published May 2013. Originally approved in 1962. Last previous edition approved in 2006 as F37 – 06. — 8 p. These test methods provide a means of evaluating the sealing properties of sheet and solid form-in-place gasket materials at room temperature. Test Method A is restricted to liquid leakage measurements, whereas Test Method B may be used...
Current edition approved June 1, 2015. Published September 2015. Originally approved in 1974. Last previous edition approved in 2009 as F377 – 03 (2009). — 5 p. This practice gives procedures for the calibration of: - reference load cells - calibration platform systems by using a reference load cell - static calibration of braking/tractive force on locked wheels of tire test...
Current edition approved March 1, 2014. Published April 2014. Originally approved in 1962. Last previous edition approved in 2006 as F38 – 00 (2006). — 9 p. These test methods provide a means of measuring the amount of creep relaxation of a gasket material at a predetermined time after a compressive stress has been applied. Test Method A - Creep relaxation measured by means of a...
Current edition approved May 1, 2015. Published June 2015. Originally approved in 1975. Last previous edition approved in 2008 as F408 – 99 (2008). — 6 p. This test method covers the measurement of braking traction of tires designed for passenger cars or light trucks. Such braking traction measurements are applicable to conditions wherein the vehicle is traveling straight ahead on...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2009. Published June 2009. Originally approved in 1975. Last previous edition approved in 2007 as F412 - 07. 16 p. This terminology is a compilation of definitions of technical terms used in the plastic piping industry. Terms that are generally understood or adequately defined in other readily...
Current edition approved June 1, 2015. Published August 2015. Originally approved in 1975. Last previous edition approved in 2009 as F414 – 09. — 4 p. This test method covers the determination of tire plunger energy required to completely penetrate the tread area of an inflated tire as indicated by a rupture, loss of inflation pressure, sudden drop in plunger force or bottom-out....
Current edition approved June 1, 2015. Published August 2015. Originally approved in 1975. Last previous edition approved in 2013 as F421 – 07 (2013)ɛ1. — 4 p. This test method describes standard procedures for measuring the groove and void depth in passenger car tires. Any mechanical, optical, or electronic device capable of measuring groove (void) depth can be used, but only the...
In: Annual Book of ASTM Standards vol. 10.04 (Electronics I). - West Honshohoken, PA: ASTM Intl., 2001. - 6 p. - Reapproved in 1997. These test methods cover the determination of the conductivity type of extrinsic semiconductors, especially germanium and silicon.
Current edition approved July 1, 2014. Published November 2014. Originally approved in 1964. Last previous edition approved in 2009 as F433 – 02 (2009). — 6 p. This practice covers a means of measuring the amount of heat transfer quantitatively through a material or system. This practice is similar to the Heat Flow Meter System of Test Method C518, but modified to accommodate...
Current edition approved May 1, 2017. Published July 2017. Originally approved in 1975. Last previous edition approved in 2009 as F434 – 93 (2009). — 3 p. This test method covers the determination of the resistance against blow-out of preformed gaskets. The test is conducted under ambient conditions and should be used for comparison purposes only to select suitable designs and...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published August 2007. Originally approved in 1976. Last previous edition approved in 2004 as F 436 – 04. 6 p. This specification covers the chemical, mechanical, and dimensional requirements for hardened steel washers for use with fasteners having nominal thread diameters of 1⁄4 through 4...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2006. Published August 2006. Originally approved in 1976. Last previous edition approved in 2006 as F 467 – 06. 10 p. This specification covers the requirements for commercial wrought nonferrous nuts 0.250 to 1.500 in. inclusive in diameter in a number of alloys in common use and intended for...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2006. Published August 2006. Originally approved in 1979. Last previous edition approved in 2006 as F 467M – 06. 10 p. This specification covers the requirements for commercial wrought nonferrous nuts in nominal thread diameters M6 to M36 inclusive in a number of alloys in common use and...
In: Annual Book of ASTM Standards vol. 10.04 (Electronics I), West Honshohoken, PA: ASTM Intl., 2001. - 6 p. These test methods cover two procedures: - Method A, Two-Probe, - Method B, Four-Probe. These procedures apply directly to both silicon and germanium. Application to other semiconductors may require the use of different probe material and probe attachments.
Current edition approved May 1, 2017. Published July 2017. Originally approved in 1976. Last previous edition approved in 2010 as F457 – 04 (2010). — 4 p. This test method covers the determination of vehicle speed and cumulative distance traveled using a device termed a fifth wheel and using appropriate associated instrumentation. This test method also describes the calibration...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2006. Published May 2006. Originally approved in 1976. Last previous edition approved in 2005 as F 468 – 05a. 11 p. This specification covers the requirements for commercial wrought nonferrous bolts, hex cap screws, and studs 0.250 to 1.500 in. inclusive in diameter manufactured from a number of...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2006. Published May11 p. This specification covers the requirements for commercial wrought nonferrous bolts, hex cap screws, and studs in nominal thread diameters M6 to M36 inclusive manufactured from a number of alloys in common use and intended for general service applications. Unless otherwise...
Current edition approved May 1, 2011. Published July 2011. Originally approved in 1977. Last previous edition approved in 2004 as F495 – 99a (2004). — 2 p. This test method covers the determination of gasket material weight loss upon exposure to elevated temperatures. This test method may include hazardous materials, operations, and equipment.
США ASTM International Актуальный стандарт 2016 год Стандартные термины, относящиеся к характеристикам и особенностям шин. Standard Terminology Relating to the Characteristics and Performance of Tires
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2006. Published August 2006. Originally approved in 1977. Last previous edition approved in 2001 as F 547 – 01. 15 p. The terms included in these definitions are listed in alphabetical order under six headings to facilitate quick reference. They are intended to apply to metal nails. Some of these...
Current edition approved Jan. 1, 2016. Published February 2016. Originally approved in 1977. Last previous edition approved in 2009 as F551/F551M – 09a. — 3 p. This practice covers the requirements for a 1.707-m [67.23-in.] diameter laboratory roadwheel for durability and endurance testing of tires under controlled operating and environmental conditions.
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2008. Published February 2008. Originally approved in 1978. Last previous edition approved in 2002 as F552 - 02. 4 p. This Standard Covers Terminology Relating to Chain Link Fencing
Current edition approved May 1, 2017. Published July 2017. Originally approved in 1978. Last previous edition approved in 2010 as F559 – 05 (2010). — 3 p. This test method covers the determination of the accurate length measurement of road courses used for testing all types of pneumatic tires on various associated vehicles. This test method is intended for use on public highways...
American Society for Tesing and Materials (ASTM). Current edition approved May 1, 2006. Published May 2006. Originally approved in 1978. Last previous edition approved in 2001 as F 592 – 84 (2001). 5 p. The terms included in these definitions are listed in alphabetical order to facilitate quick reference. They are intended to apply to collated and cohered nails, staples, and pins...
American Society for Testing and Materials (ASTM). Current edition approved April 10, 2002. Published May 2002. 8 р. This specification covers the requirements for stainless steel bolts, hex cap screws, and studs 0.25 to 1.50 in., inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance.
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published September 2007. Originally approved in 1979. Last previous edition approved in 2006 as F 606 – 06. 15 p. These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers, direct...
ASTM 1998, 12p. F 606 Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets Brief Summary These test methods establishes the standard procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers and direct tension indicators, and...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 1, 2007. Published September 2007. Originally approved in 1987. Last previous edition approved in 2005 as F 606M – 05. 15 p. These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of metric externally and internally threaded fasteners,...
Current edition approved July 1, 2014. Published November 2014. Originally approved in 1979. Last previous edition approved in 2008 as F607 – 03 (2008). — 4 p. This test method provides a means of determining the degree to which gasket materials under compressive load adhere to metal surfaces. The test conditions described are indicative of those frequently encountered in gasket...
American Society for Testing and Materials (ASTM). 2006. 5p. This specification covers the chemical, mechanical, and metallurgical requirements for four grades of unalloyed titanium strip, sheet, plate, bar, billet, forging, and wire used for the manufacture of surgical implants. The values stated in inch-pound units are to be regarded as the standard. The SI equivalents in...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published October 2005. Originally approved in 1966. Last previous edition approved in 2004 as F 68 – 99 (2004). 6 p. This specification establishes the requirements for wrought and fabricated shapes made from Copper UNS2 No. C10100, conforming to the chemical requirements of Specification B...
Current edition approved Jan. 1, 2016. Published February 2016. Originally approved in 1981. Last previous edition approved in 2010 as F724 – 94a (2010)ɛ1. — 7 p. This test method covers procedures for evaluating passenger car tires for sidewall component integrity and cracking resistance, using an outdoor roadwheel. This test method evaluates the resistance of tire sidewalls to...
American Society for Testing and Materials (ASTM). 2002. 9p. This specification covers the chemical and mechanical requirements for stainless steel metric bolts, screws, and studs with nominal thread diameters M1.6 through M36 and is intended for use in engineering applications requiring general corrosion resistance.
American Society for Testing and Materials (ASTM). Current edition approved Feb. 1, 2006. Published February 2006. Originally approved in 1982. Last previous edition approved in 2005 as F 747 - 05. 4 p. This Standard Covers Terminology Relating to Amusement Rides and Devices
Current edition approved June 1, 2014. Published November 2014. Originally approved in 1982. Last previous edition approved in 2008 as F762/F762M – 08. — 4 p. This test method covers a procedure to be used to obtain data for determining the changes in tire tread depth over any specified course and test period. The tire tread depth loss data obtained according to the procedures for...
In: Annual Book of ASTM Standards vol. 10.04 (Electronics I), West Honshohoken, PA: ASTM Intl., 2001. - 13 p. - Reapproved 1996. These test methods cover two procedures differing most substancially in test specimen requirements, especially their shape: - Method A, van der Pau, - Method B, Parallelepiped, or Bridge-Type.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2007. Published December 2007. Originally approved in 1982. Last previous edition approved in 2006 as F 788/F 788M – 06. 6 p. This specification establishes allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and...
Current edition approved May 1, 2017. Published July 2017. Originally approved in 1983. Last previous edition approved in 2009 as F806 – 99a (2009). — 3 p. This test method covers determination of the short-time compressibility and recovery at room temperature of laminated composite gasket materials. This test method is not intended as a test for compressibility under prolonged...
In: Annual Book of ASTM Standards vol. 10.04 (Electronics I), West Honshohoken, PA: ASTM Intl., 2001. - 9 p.
This test method provides procedures for the determination of relative radial resistivity variation of semiconductor wafers cut from silicon single crystals grown either by the Czochralski or floating-zone technique.
Описан метод определения относительной радиальной...
Current edition approved Jan. 1, 2016. Published February 2016. Originally approved in 1983. Last previous edition approved in 2010 as F811 – 02 (2010). — 4 p. This practice covers guidelines for using accelerometers in test vehicles to evaluate dynamic accelerations resulting from various maneuvers such as braking, accelerating, or cornering. This practice is applicable to...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2007. Published December 2007. Originally approved in 1983. Last previous edition approved in 2003 as F 812/F 812M – 03. 5 p. This specification establishes allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of metric-series nuts...
American Society for Testing and Materials, 1983. - 6 pp.
This test method applies to hermetic package leak testing to detect leaks of a broad spectrum in size with a mimimum detection limit equal to the sensitivity of the helium mass spectrometer equipment used in the test.
Настоящий стандарт относится к области определения вакуумных течей в герметичных корпусах, и...
American Society for Testing and Materials (ASTM). Current edition approved Aug. 1, 2007. Published August 2007. Originally approved in 1983. Last previous edition approved in 2004 as F 844 – 04. 4 p. This specification covers round and miscellaneous shape steel plain (flat) washers furnished in an unhardened condition. The washers are intended for general use bolt, nut, and...
In: Annual Book of ASTM Standards vol. 10.04 (Electronics I), West Honshohoken, PA: ASTM Intl., 2001. - 13 p.
This test method covers the measurement of the resistivity of silicon wafers with a in-line four probe measurements.
Current edition approved May 1, 2017. Published May 2017. Originally approved in 1984. Last previous edition approved in 2009 as F868 – 02 (2009). — 4 p. This classification covers a means for specifying or describing pertinent properties of commercial laminate composite gasket materials (LCGM). These structures are composed of two or more chemically different layers of material....
Current edition approved Jan. 1, 2016. Published February 2016. Originally approved in 1984. Last previous edition approved in 2010 as F870 – 94 (2010). — 5 p. This practice covers a technique for measuring the groove or void area of a tire tread pattern. The void area is measured on the inked impression of a tire tread statically loaded against heavyweight paper on a load platen....
American Society for Testing and Materials (ASTM). Current edition approved July 15, 2007. Published July 2007. Originally approved in 1984. Last previous edition approved in 2001 as F 901 – 01. 4 p. This specification covers aluminum structural bolts and nuts for use in the construction of aluminum transmission towers, substations, and similar aluminum structures. Diameters of...
In: Annual Book of ASTM Standards vol. 10.04 (Electronics I), West Honshohoken, PA: ASTM Intl., 2001. - 7 p. - Reapproved 2000.
This test method provides a technique for measurement of thickness of lightly doped silicon epitaxial layers on heavily doped silicon substrates using an infrared dispersive spectrophotometer.
American Society for Testing and Materials (ASTM). Current edition approved April 1, 2007. Published April 2007. Originally approved in 1985. Last previous edition approved in 2006 as F 959 – 06. 4 p. This specification covers the requirements for compressible-washer-type direct tension indicators capable of indicating the achievement of a specified minimum bolt tension in a...
American Society for Testing and Materials (ASTM). Current edition approved Nov. 1, 2006. Published November 2006. Originally approved in 1994. Last previous edition approved in 2004 as F 959M – 04. 5 p. This specification covers the requirements for compressible-washer-type direct tension indicators capable of indicating the achievement of a specified minimum bolt tension in a...
American Society for Testing and Materials, 1999. – 5 p. This guide describes the steps required to conduct a complete repeatability and reproducibility (RR) study on nondestructive test equipment. This guide is a manual (use of calculator) method. Other methods may utilize the application of computer driven software.
ASTM International, 2006. — 74 p. This practice consists of three annexes: hull structure, outfitting, and coating. The subject of these annexes was selected for several reasons. Other commercial shipbuilding nations already have in place widely recognized standards of expectations in these areas. These constitute the most significant areas where workmanship is a critical...
ASTM International, 2006. — 11 p. This guide identifies factors relevant to the quality of language translation services for each phase of a translation project. The guide is intended for use by all stakeholders, with varying levels of knowledge in the field of translation.
ASTM 2003-9p, G 1 (Standard Practice for Preparing, Cleaning, and Evaluating Corrosion Test Specimens) Significance and Use The procedures given are designed to remove corrosion products without significant removal of base metal. This allows an accurate determination of the mass loss of the metal or alloy that occurred during exposure to the corrosive environment. These...
ASTM 2004, 5p. G 15 Standard Terminology Relating to Corrosion and Corrosion Testing Scope This terminology covers commonly used terms in the field of corrosion. Related terms may be found in Terminologies D 16, D 4538, G 40, or other ASTM terminology standards. All terms defined by ASTM committees may be found in the ASTM Dictionary of Engineering & Technology.
American Society for Testing and Materials (ASTM). Current edition approved Nov. 15, 2006. Published April 2007. Originally approved in 1997. Last previous edition approved in 2000 as G 151 – 00. 15 p. This practice provides general procedures to be used when exposing nonmetallic materials in accelerated test devices that use laboratory light sources. Detailed information...
American Society for Testing and Materials (ASTM). Current edition approved Oct. 1, 2005. Published November 2005. Originally approved in 1997. Last previous edition approved in 2005 as G 155 – 05. 11 p. This practice covers the basic principles and operating procedures for using xenon arc light and water apparatus intended to reproduce the weathering effects that occur when...
American Society for Testing and Materials (ASTM). 2006. 16p. This guide covers some generally accepted laboratory methodologies that are used for evaluating corrosion inhibitors for oilfield and refinery applications in well defined flow conditions.
ASTM 1988(Reapproved 1998), 5p. G 18 Standard Test Method for Joints, Fittings, and Patches in Coated Pipelines Significance and Use The exposed metal surfaces at joints, fittings, and damaged areas in an otherwise coated pipeline will be subjected to corrosion if allowed to come in contact with the soil environment. The performance of joint and patching materials designed to...
ASTM 1988(Reapproved 1996), 4p. G 19 Standard Test Method for Disbonding Characteristics of Pipeline Coatings by Direct Soil Burial Scope This test method describes the determination of the relative disbonding characteristics of damaged coatings on steel pipe by cathodic protection potentials in direct soil burial. This test method is intended to apply to the testing of all...
ASTM 2002, 7p. G 28 Standard Test Methods of Detecting Susceptibility to Intergranular Corrosion in Wrought, Nickel-Rich, Chromium-Bearing Alloys Significance and Use The boiling ferric sulfate-sulfuric acid test may be applied to the following alloys in the wrought condition: Alloy Testing Time, h N06007- 120 N06022- 24 N06030- 120 N06059- 24 N06200- 24 N06455- 24 N06600- 24...
ASTM 2003, 11p G 48. Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution Significance and Use These test methods describe laboratory tests for comparing the resistance of stainless steels and related alloys to the initiation of pitting and crevice corrosion. The results may be used for...
Стандартные методы испытаний на стойкость к питтинговой и щелевой коррозии нержавеющих сталей и соответствующих сплавов при использовании раствора хлорида окисного железа
ASTM 1985 (Reapproved 2000), 6p. G 49 Standard Practice for Preparation and Use of Direct Tension Stress-Corrosion Test Specimens Significance and Use Axially loaded tension specimens provide one of the most versatile methods of performing a stress-corrosion test because of the flexibility permitted in the choice of type and size of test specimen, stressing procedures, and...
ASTM 1988 (Reapproved 1998), 4p, G 6 Standard Test Method for Abrasion Resistance of Pipeline Coatings Significance and Use This procedure defines a test method for comparing the relative resistance of pipeline coatings to abrasion. Abrasion resistance may be used to specify optimum coating thickness of candidate materials both in development and research work to study new...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 25, 1987. Published November 1987. Originally published as G 62 – 79. Last previous edition G 62 – 85. 4 p. These test methods cover the apparatus and procedure for detecting holidays in pipeline type coatings. Method A is designed to detect holidays such as pinholes and voids in thin-film...
American Society for Testing and Materials (ASTM). Current edition approved May 1, 2011. Published August 2011. Originally approved in 1985. Last previous edition approved in 2009 as G85–09. 14 p. This practice covers and sets forth conditions for five modifications in salt spray (fog) testing for specification purposes. These are in chronological order of their development:...
American Society for Testing and Materials (ASTM). Current edition approved Sept. 25, 1987. Published November 1987. 4 p. This test method covers accelerated procedures for simultaneously determining comparative characteristics of coating systems applied to steep pipe exterior for the purpose of preventing or mitigating corrosion that may occur in underground service where the...
8 стр. Язык: русский Настоящие технические условия распространяются на контактный, эхо-импульсный метод ультразвукового контроля массивных стальных поковок с помощью прямого и наклонного пучков. Технология контроля прямым пучком включает применение метода DGS (Зависимость дистанционного усиления от размера). См. Приложение X3.
9 p.
This practice covers the examination procedures for the contact, pulse-echo ultrasonic examination of heavy steel forgings by the straight and angle-beam techniques. The straight beam techniques include utilization of theDGS (Distance Gain-Size) method. See Appendix X3.
2007, ASTM — 81 p. This Specification covers a group of common requirements that, unless otherwise specified in the material specification, apply to rolled steel plates, shapes, sheet piling and bars.
ASTM Standards Volume 02.02 Aluminum and Magnesium Alloys
Сборник стандартов Американского общества по испытаниям и материалам – ASTM. Сборник содержит 220 стандартов по алюминиевым и магниевым сплавам. Стандарты содержат изменения, дополнения, замены по состоянию на 2004 год. Текущие изменения, естественно, отсутсутствуют. Только для информации и ознакомления
Сборник стандартов Американского общества по испытаниям и материалам – ASTM. Сборник содержит 196 стандартов по коррозии металлов, изнашиванию и истиранию. Стандарты содержат изменения, дополнения, замены по состоянию на 2004 год. Текущие изменения, естественно, отсутсутствуют. Только для информации и ознакомления
Стандартные методы испытаний и определения, применяемые для механических испытаний стальных изделий 1
Настоящий стандарт выпущен под постоянным обозначением А
370. Номер, следующий непосредственно за обозначением стандарта, указывает на год первоначального принятия стандарта или, в случае внесения каких-либо исправлений, на год выпуска последней редакции стандарта. Номер в...
Обозначение: А 788 – 94 Американский национальный стандарт Стандартные технические условия на стальные поковки, Общие требования Настоящий стандарт выпущен под постоянным обозначением А 788. Номер, следующий непосредственно за обозначением стандарта, указывает на год первоначального принятия стандарта или, в случае исправлений, на год выпуска последней редакции. Номер в скобках...
Платформа: PC (Windows). — Совместимость с Windows 7 полная. — Язык интерфейса: английский + русский.
Расчётные ASTM таблицы по нефти и нефтепродуктам 5A, 6A, 5B, 6B, 6C, 23A, 24A, 23B, 24B, 24C, 53A, 54A, 53B, 54B, 54C.
ASTM / API TABLES
TABLE 54A (Crude Oil).
TABLE 54B (Products).
TABLE 6A (Crude Oil).
TABLE 6B (Products).
Temperature Deg. F to Deg. C.
Temperature...
COPYRIGHT ASTM International. Licensed by Information Handling Services. Настоящий стандарт разработан в связи с необходимостью наличия единого стандарта, который включал бы все аспекты проведения и составления отчетности химического анализа стали, нержавеющей стали, сплавов. Такие вопросы как определения терминов и отклонения (допустимые значения) результатов испытаний анализа...
Настоящий стандарт устанавливает методы механических испытаний для определения характеристик трещиностойкости металлов при статическом кратковременном нагружении на образцах толщиной не менее 1 мм при температуре от минус 269 °С до плюс 600°С.
ASTM D 1267-02(2007) - Standard Test Method for Gage Vapor Pressure of Liquefied Petroleum (LP) Gases (LP-Gas Method) / Стандартный метод анализа давления избыточных паров сжиженных нефтяных газов (Метод для Сжиженных газов); ASTM D 1835-05 - Standard Specification for Liquefied Petroleum (LP) Gases / Стандартные технические условия для сжиженных нефтяных газов; ASTM D 1838-07...
ASTM D 2421-02(2007) - Standard Practice forInterconversion of Analysis of C5 and Lighter Hydrocarbons to Gas-Volume, Liquid-Volume, or Mass Basis / Стандартная методика взаимопересчета анализа С5 и более легких углеводородов на газ-объем, жидкость-объем, или на весовую основу; ASTM D 2598-02(2007) - Standard Practice for Calculation of Certain Physical Properties of Liquefied...
Сборник стандартов ASTM на английском и русском языках. Форматы: DOC, PDF ASTM D 5853-06 - Стандартный метод анализа по определению температуры застывания сырой нефти / Standard Test Method for Pour Point of Crude Oils; ASTM 2887 - 08 - Стандартный метод испытания для определения распределения точек кипения нефтяных фракций методом газовой хроматографии / Standard Test Method...
ASTM A 216 -93 Стандартные технические условия на стальные отливки из углеродистой стали, пригодные для сварки плавлением и работающие в условиях высоких температур
ASTM A 217-02 Стандартные технические условия на стальные отливки из мартенситных нержавеющих сталей и сплавов для, работающих под давлением и в условиях повышенных температур
ASTM A 351-90 Стандартные...
В данном сборнике собраны спецификации на трубные стали, применяемые при изготовлении труб, трубных деталей и арматуры. Всего в архиве 435 спецификаций по сталям классов от А53 до А1024
Комментарии